Miele G 7883 User Manual

To open the door with the
emergency release
The emergency release should only be
used when the door cannot be opened
normally, e.g. in the event of a power
failure.
^Turn the program selector to Stop
f.
^Press the On/Off button to turn the
machine off.
^Take precaution against pressure
wave release (rapid opening of the
door).^Pull the emergency release cable
(located at the bottom of the machine
behind the service panel) downwards
to open the door.
The door latch will reset after the
emergency cable has...

Before using the machine for the first
time, the water softener should be
programmed. The water needs to be
softened to avoid calcium deposit
buildup on the items being cleaned and
in the machine itself.
To ensure a steady supply of soft water:
1. Make sure the water softener is
programmed correctly.
The softener contains settings from
1 - 60 gr/gal or 20 - 1080 ppm.
2. The salt reservoir must be filled with
reactivation salt.
(If the water hardness level is below
4 gr/gal [70 ppm]), the reservoir
does...

Settings
Settings
1 - 30gr/gal
1 - 30ppm
CaCO
3
Settings
31 - 60gr/gal
31 - 60ppm
CaCO
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
301
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 *)
20
21
22
23
24
25
26
27
28
29
3020
40
50
70
90
110
130
140
160
180
200
220
230
250
270
290
310
320
340
360
380
400
410
430
450
470
490
500
520
54031
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
6031
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48...

Setting the water softener
^Turn off the machine with the On/Off
button.
^Turn the program selector to the
Stopfposition.
^Press and hold the Start6and
Displayßbuttonsat the same
time. Turn the machine on with the
On/Off button.
The current program status P... will
appear in the display.
The Fill/Drain indicator will
illuminate.
The first time the water softener is set
the Recharge Softener light will
illuminate. This light will also illuminate
after restoring the factory settings, see
Programming...

Filling the salt reservoir
Only special, coarse-grained
reactivation salt* should be used in
this machine.
*Available from Miele’s Professional
Customer Service Department.
Please see back page for more
information.
Do not use other types of salt, e.g. table
salt, agricultural or gritting salt. These
could contain components which are
insoluble in water and could damage
the water softener. If in doubt, consult
Miele’s Professional Department.
The salt reservoir holds approx. 2.5 kg
of salt....

Salt indicator
When the salt reservoir is empty the
Recharge Softener indicator,b,
illuminates to  remind you to fill the
reservoir.
Reactivation takes place automatically
during a program. The Recharging
indicator,a, illuminates while this is
occurring.
Water softener
16 

Rinse aid is not used in laboratory
glassware cleaning applications.
If rinse aid is required, the rinse aid
dosage must be activated with
assistance from Miele Technical
Service.
Rinse aid (e.g. Mielclear) is filled in the
storage container and dispensed
automatically. The storage reservoir
holds about 180 ml.
,Inadvertently filling the storage
reservoir with detergent will damage
the reservoir.Be sure only to use
rinse aid in the reservoir.
^
If the Add Rinse aid indicator
illuminates, the rinse aid...

Setting the rinse aid dosage
The dosage adjuster (see arrow in the
illustration) in the opening has settings
adjustable from 1 to 6 (1 - 6 ml).
It is preset to 3 (3 ml).
^Use a flat headed screwdriver to turn
the dial to the correct setting.
If spots remain on the items, use a
higher setting.
If smearing or cloudy streaks appear,
use a lower setting.
Adding rinse aid
18 

Neutralizer (pH-level: acidic)
neutralizes detergent residue on the
surface of glassware and other items
being cleaned. It is automatically
dispensed in the rinse following the
wash step of a program.
The relevant program (see Program
Guide - DOS 3) cannot be started until
the dispensing system has been
primed. (This function can only be
canceled by a Miele Service Engineer.)
^Place the container of neutralizer
(red) next to the machine.
When the Add neutralizer indicator
illuminates:^Insert the siphon...

Setting the neutralizer dosage
and priming the neutralizer
dispensing system
First you need to access the
programming mode:
To access the programming mode
^Turn the program selector to Stop
f.
^Turn the machine off.
^Press and hold the Displayßand
Start6button.At the same time
turn the lab washer on by the main
switchI-0.
The display shows the current
program status P....
The Fill/Drain indicator lights.
^Press the Drying0button twice.
E02 (programming level 2) appears
in the display.The dosage is...