Miele G 7883 User Manual

							To open the door with the
emergency release
The emergency release should only be
used when the door cannot be opened
normally, e.g. in the event of a power
failure.
^Turn the program selector to Stop
f.
^Press the On/Off button to turn the
machine off.
^Take precaution against pressure
wave release (rapid opening of the
door).^Pull the emergency release cable
(located at the bottom of the machine
behind the service panel) downwards
to open the door.
The door latch will reset after the
emergency cable has been activated.
Opening and closing the door
11 
						

							Before using the machine for the first
time, the water softener should be
programmed. The water needs to be
softened to avoid calcium deposit
buildup on the items being cleaned and
in the machine itself.
To ensure a steady supply of soft water:
1. Make sure the water softener is
programmed correctly.
The softener contains settings from
1 - 60 gr/gal or 20 - 1080 ppm.
2. The salt reservoir must be filled with
reactivation salt.
(If the water hardness level is below
4 gr/gal [70 ppm]), the reservoir
does not need to be filled.)
The machine is set at the factory for a
water hardness level of 19 gr/gal
(340 ppm).
Your local water authority will advise
you on the water hardness in your
area. If the water supply is harder or
softer than the factory setting
(including below 4 gr/gal or
70 ppm), the setting will need to be
changed. See Setting the water
softener.
Water softener
12 
						

							Settings
Settings
1 - 30gr/gal
1 - 30ppm
CaCO
3
Settings
31 - 60gr/gal
31 - 60ppm
CaCO
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
301
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 *)
20
21
22
23
24
25
26
27
28
29
3020
40
50
70
90
110
130
140
160
180
200
220
230
250
270
290
310
320
340
360
380
400
410
430
450
470
490
500
520
54031
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
6031
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60560
580
590
610
630
650
670
680
700
720
740
760
770
790
810
830
850
860
880
900
920
940
950
970
990
1010
1030
1040
1060
1080
*)factory setting
Water softener
13 
						

							Setting the water softener
^Turn off the machine with the On/Off
button.
^Turn the program selector to the
Stopfposition.
^Press and hold the Start6and
Displayßbuttonsat the same
time. Turn the machine on with the
On/Off button.
The current program status P... will
appear in the display.
The Fill/Drain indicator will
illuminate.
The first time the water softener is set
the Recharge Softener light will
illuminate. This light will also illuminate
after restoring the factory settings, see
Programming special functions.
^Press the Drying0button once.
E01 (programming level 1) will
appear in the display.
^Turn the program selector one switch
position clockwise (1 o’clock
position).
The number 19 will appear in the
display (this indicates the factory
water hardness setting in gr/gal,
equivalent to 340 ppm).
^
Press the Displayßbutton as
many times as necessary, or hold it in
until the required value (hardness
level in gr/gal) appears in the display.
Once the number 60 has been
reached, the counter will begin again
at 0.
^
Press the Start6button. SP will
appear in the display.
^
Press the Start6button again.The setting will now be stored in
memory. The display will go out.
For future servicing, it is useful to make
a note of your water hardness level.
^Enter your water hardness level here:
gr/gal
or
ppm
^If your water is already soft and you
would like to deactivate the water
softener, set the hardness setting to
0.
Water softener
14 
						

							Filling the salt reservoir
Only special, coarse-grained
reactivation salt* should be used in
this machine.
*Available from Miele’s Professional
Customer Service Department.
Please see back page for more
information.
Do not use other types of salt, e.g. table
salt, agricultural or gritting salt. These
could contain components which are
insoluble in water and could damage
the water softener. If in doubt, consult
Miele’s Professional Department.
The salt reservoir holds approx. 2.5 kg
of salt.
,Inadvertently filling the salt
reservoir with detergent will damage
the water softener.
Before filling, make sure that you are
usingreactivation salt.
^
Remove the bottom basket from the
machine.
^
Unscrew the salt reservoir cap.
Before filling the salt reservoir with
reactivation salt for the first time fill it
with approx. 2.5 liters of water.^Place the funnel provided in place.
^Carefully fill the reservoir with salt.
Displaced water will run out as it is
being filled.
^Wipe any residual salt off the screw
threads on the socket.
^Screw the cap on firmly.
^Immediately after this step:Run the
Rinse program to remove any traces
of salt from the cabinet.
Note:There may be a delay before the
Rinse program starts due to the
reactivation of the water softener.
Water softener
15 
						

							Salt indicator
When the salt reservoir is empty the
Recharge Softener indicator,b,
illuminates to  remind you to fill the
reservoir.
Reactivation takes place automatically
during a program. The Recharging
indicator,a, illuminates while this is
occurring.
Water softener
16 
						

							Rinse aid is not used in laboratory
glassware cleaning applications.
If rinse aid is required, the rinse aid
dosage must be activated with
assistance from Miele Technical
Service.
Rinse aid (e.g. Mielclear) is filled in the
storage container and dispensed
automatically. The storage reservoir
holds about 180 ml.
,Inadvertently filling the storage
reservoir with detergent will damage
the reservoir.Be sure only to use
rinse aid in the reservoir.
^
If the Add Rinse aid indicator
illuminates, the rinse aid storage
container needs to be refilled.
The storage container has a level
indicator on the interior of the door.
^
Open the door.^Unscrew the cap.
^
Pour rinse aid into the storage
container until the level indicator is
dark (see arrow in the illustration).
Use a funnel if necessary.
^
Replace and tighten the cap. Clean
up any spilled rinse aid to prevent
oversudsing in the next wash.
^
Wait until the Rinse indicator on the
control panel illuminates before
adding any more rinse aid.
Adding rinse aid
17 
						

							Setting the rinse aid dosage
The dosage adjuster (see arrow in the
illustration) in the opening has settings
adjustable from 1 to 6 (1 - 6 ml).
It is preset to 3 (3 ml).
^Use a flat headed screwdriver to turn
the dial to the correct setting.
If spots remain on the items, use a
higher setting.
If smearing or cloudy streaks appear,
use a lower setting.
Adding rinse aid
18 
						

							Neutralizer (pH-level: acidic)
neutralizes detergent residue on the
surface of glassware and other items
being cleaned. It is automatically
dispensed in the rinse following the
wash step of a program.
The relevant program (see Program
Guide - DOS 3) cannot be started until
the dispensing system has been
primed. (This function can only be
canceled by a Miele Service Engineer.)
^Place the container of neutralizer
(red) next to the machine.
When the Add neutralizer indicator
illuminates:^Insert the siphon tube into the
container (observe the color code).
Setting the dosage and priming the
dispensing system
^See Programming special functions.
Important
The container should not be allowed
to empty completely.
Adding neutralizing agent
19 
						

							Setting the neutralizer dosage
and priming the neutralizer
dispensing system
First you need to access the
programming mode:
To access the programming mode
^Turn the program selector to Stop
f.
^Turn the machine off.
^Press and hold the Displayßand
Start6button.At the same time
turn the lab washer on by the main
switchI-0.
The display shows the current
program status P....
The Fill/Drain indicator lights.
^Press the Drying0button twice.
E02 (programming level 2) appears
in the display.The dosage is factory set to 0.10, you
may or may not be required to adjust it.
Set the dosage concentration
according to the detergent
manufacturer’s recommendations.
Example:
The manufacturer recommends a
neutralizer concentration of 0.3 %. The
value to be set is 0.30.
^First access the programming level to
E02.
^Turn the program selector clockwise to
Intensive.
The display shows the set dosage
concentration in % from 0.05 % -
0.5 %.
^Press and hold the Displayß
button until the desired value
appears.
The dosage time / dosage
concentration is saved.
^
Please note the dosage setting:
To store the settings
^
Press the Start6button. SP
appears in the display.
^
Press the Start6button again. The
change has been saved.
NOTE:This change will set the
neutralizer dispensing amount for all
wash programs that use neutralizer.
Adding neutralizing agent
20