Miele G 7883 User Manual

							INSTALLATION INSTRUCTIONS 
						

							Disposal of the packing
material
The protective packing materials are
environmentally safe and can be
recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Disposal of the appliance
Appliances contain materials which can
be recycled. Please contact your local
authorities about recycling in your area.
Ensure that the machine presents no
danger to children while being stored
for disposal. See Important Safety
Instructions.
Caring for the environment
52 
						

							Please refer to the installation
diagram supplied with the machine.
,Furniture and fittings installed
near the machine must be of a
commercial standard (able to
withstand the effects of steam).
Installation options
–Free-standing
–Undercounter
The machine can be installed under a
continuous counter or sink drain. The
recess must be at least 60 cm wide,
60 cm deep and 82 cm high.
Positioning and securing the
machine
To ensure stability, the machine must be
aligned and screwed to the counter.
^Open the door.
^Secure the machine to the front edge
of the worktop using the screws to
the left and right of the front trim.
^When not mounted undercounter,
floor mounting brackets must be
used.
Do not use silicone sealant to seal
the gaps between the machine and
any neighboring units. This will
hinder ventilation to the circulation
pump.
Steam Deflector (protects the
countertop)
Depending on the requirements for an
undercounter installation, a steam
deflector can be ordered from the Miele
Technical Service Department.
The underside of the countertop is
protected from steam damage by a
stainless steel plate.
Installation
53 
						

							Removing the lid (if necessary)
If necessary, remove the lid from the
machine to make installation possible.
^Open the door.
^Remove the fixing screws on the left
and right sides using a phillipshead
screwdriver.
^Pull the machine lid approx. 5 mm
forwards, lift it upwards and remove.Important for machines with steam
condenser (depending on model)
^To prevent countertop damage by
steam, the supplied self adhesive
protective foil (25 x 58 cm) must be
placed underneath the countertop
near the steam condenser.
Installation
54 
						

							Water inlet
^The machine must be connected to
the water supply in accordance with
local and national regulations.
^The washer is constructed so it may
be connected to a supply without an
extra non-return valve, unless
required by code.
^An acceptable water pressure (flow
rate) is 10 - 147 psi. However, the
recommended pressure is
25 - 60 psi.
If the water pressure is below 30 psi,
the fill time will take longer.
If the Fill/Drain fault code F..E is
displayed, contact the Technical
Service Department.
^The machine is supplied to be
connected to a standard cold (coded
blue)orhot (coded red) water supply
to a maximum temperature of 158 °F
(70 °C.)
Connect the water intake hoses to the
cold and hot water faucets.
If no hot water supply is available, the
hot water intake hose with thered
marking needs to be connected to
cold water by a y-adapter.
For a DI water connection (H
2O
pure), see the next page.^Water valves with
3/4 male hose
thread are to be provided on site.
They should be easily accessible so
the water supply can be turned off if
necessary.
^The inlet hoses are 5
½feet (1.7 m)
long, terminating in a3/4 female hose
thread.The water inlet filters in the
threads must not be removed.
^Large surface area filters are
enclosed in the kit supplied with the
machine.
Install these filters between the water
valve and the water inlet hose (see
illustration in Machine Care/Cleaning
the filters in the water inlet). The
large surface area filter for DI water is
made from stainless steel and can be
recognized by its matte surface.
,Do not cut the inlet hose or
damaged it in any way.
^
See the supplied installation diagram.
Plumbing
55 
						

							DI-Water connection
The machine comes with a standard
connection for a pressure-resistant
system. The recommended water
pressure (flow rate) is 25 - 60 psi
however, water pressure of 10 - 147 psi
is acceptable.
^The DI pressure-tested hose (marked
H
2O pure) with a3/4 hose thread
must be connected to the on-site
water valve for DI purified water.
If the DI water connection is not
used, the electronics needs to be
reprogrammed by a Miele technician.
The water intake hose remains at the
rear side of the machine.
Plumbing
56 
						

							Drainage
^The drainage system is fitted with a
non-return valve which prevents dirty
water from flowing back into the
machine via the drain hose.
^The machine should preferably be
connected to aseparatedrainage
system onsite.
If separate drainage is not available
contact your Miele application
specialist for advice.
The onsite drain connection point
should be located between 1 ft.
(0.3 m) and 3 ft. (1 m)above the
lower edge of the machine.
If it is lower than 1 ft. (0.3 m), lay the
hose in a curve at a height of at least
1 ft. (0.3 m).
The drainage system must be able to
take a minimum drainage flow of
16 l/min.
^The drain hose is approx. 5 ft. (1.5 m)
long, is flexible and has an internal
diameter of
7/8in. (22 mm). It must
not be shortened. Hose clamps are
supplied for securing it in position.
^
A longer drain hose (up to 12 ft. [4 m]
long) is available to order from the
Miele Technical Service Department.
^
The drainage system must not
exceed 12 ft. (4 meters).
^
See the supplied installation diagram.
Plumbing
57 
						

							,All electrical work must be
performed by a qualified person in
accordance with local and national
safety regulations.
The machine comes equipped for
connection to a 208 V, 60 Hz, 3 phase
power supply. It is equipped with a 6 ft.
long, 12/4 AWG power cord, without a
plug. A plug, rated for the required
power which will fit the receptacle, is to
be supplied by the electrician doing the
installation. It should be connected to
the main power supply.
Voltage: 208 V, 3 phase
Frequency: 60 Hz
Rated Load: 6 kW
Circuit breaker: 3 x 20 A
Black : connect to L1 (hot)
Red: connect to L2 (hot)
White: connect to L3 (hot)
Green: connect to GND (ground)It can be converted to use a single
phase power supply in accordance
with the conversion and wiring diagram.
The cord must be changed from a
12/4 AWG to a 10/3 AWG. Contact
Miele Technical Service for more
information
Voltage: 208 V, 1 phase
Frequency: 60 Hz
Rated Load: 6 kW
Circuit breaker: 2 x 30 A
^Connection should be made via a
suitable isolator, with an On/Off
button easily accessible for servicing
work.
^A damaged power cord must only be
replaced with a genuine Miele cord
by a Miele service technician.
WARNING
THIS APPLIANCE MUST BE
GROUNDED
Electrical connection
58 
						

							Grounding connection
^The ground lead must be connected
to the screw connection point
(marked with the ground symbol8) at
the back of the machine.
The machine must only be operated
with the voltage, frequency and
fusing shown on thedata plate
located on the rear of the machine,
and on the plinth (behind the service
panel).
Theconversion diagramand the
wiring diagramis secured to the inner
side of the service panel.
Removing the service panel
Disconnect the machine from the
main electrical supply.
^Remove the fixing screws,a, from
the service panel.
^Hold the service panel at both sides
and pull upwards.
^Unscrew the facing,b. Remove the
plastic protective cap.
^See the supplied installation diagram.
Re-assembling the service
panel
^Refit the plastic protective cap,
facing and service panel in the
reverse order to which they were
removed.
Electrical connection
59 
						

							English Metric
Height: 33
7/16 (325/16) 85 (82) cm
Width: 23
5/8 60 cm
Depth: 23
5/8 60 cm
Voltage: 208 V
Power cord approx. 5’ 11 1.8 m
Water pressure (flow rate):
Recommended 25 - 60 psi 1.72 - 4.13 bar
Acceptable 10 - 147 psi .7 - 10 bar
Cold or Hot water
connection up to max. 158°F 70 °C
DI-Water connection
Recommended 25 - 60 psi 1.72 - 4.13 bar
Acceptable 10 - 147 psi .7 - 10 bar
Delivery head: min. 12 0.3 m
max. 39
3/81 m
Drainage length: max. 13’ 1 4 m
Water intake hose approx. 5’ 7 1.7 m
Drain hose: approx. 4’ 7 1.4 m
Noise level in dB (A):
Sound pressure level LpA At machine 1 m (39
3/8) away
Free stand unit: 64.8 52.9
Built under counter: 62 50.1
Technical data
60