Miele G 7883 User Manual

							3. Setting the buzzer
A buzzer can be set to signal the
following:
–End of program = continuous buzzer
–Error = rhythmic buzz
–Timer to allow sampling of the last
final rinse water
= intervals of 3 short buzzes and
2 seconds break
^Turn the program selector to STOP
f.
^Turn the machine off.
^Press and hold Displayßand
Start6.At the same time,turn the
lab washer on with the On/Off
button.
The displays shows the current
program status P....
The Fill/Drain indicator lights.
^Press Drying04 times. E04
appears in the display.^Turn the program selector to
Inorganica. A number between 20
and 27 appears in the display.
20 = Buzzer is turned off
21 = End of program
(factory setting)
22 = Error
23 = Error and End of program
24 = Test sample extraction
25 = End of program and
Test sample extraction
26 = Error and Test sample
extraction
27 = All functions
(End of program, Error,
Test sample extraction).
^Press and hold Displayßuntil the
desired value appears in the display.
^Press the Start6button. SP
appears in the display.
^Press the Start6button again. The
change has been saved.
^Please note the changed setting:
To turn the buzzer off:
^
Turn the program selector to STOP
for press the Displayßbutton.
Programming special functions
41 
						

							4. Restoring the factory
settings
^Turn the program selector to STOP
f.
^Turn the machine off.
^Press and hold Displayßand
Start6.At the same time,turn the
lab washer on with the On/Off
button.
The displays shows the current
program status P....
The Fill/Drain indicator lights.
^Press and hold Drying0until E33
appears in the display.
^Turn the program selector to any
position (except STOP).
The display shows either 00 or PP.
00 = factory setting; electronic was
not reprogrammed.
PP = electronic was reprogrammed.
^If PP is displayed press Displayß
to change from PP to 00.
^
Press the Start6button. SP
appears in the display.
^
Press the Start6button again.
All factory settings are now restored.
If the hardness level setting in the
water softener had been changed,
this will reset to the factory setting of
340 ppm (19 gr/gal). This will need
to be reset to suit the hardness level
in your area.
Changes in programs Custom,
Inorganica and Organica cannot
be reset.
Programming special functions
42 
						

							Filter combination
,The machine must not be used
without all the filters in place. The
filters protect the circulation pump
from damage caused by foreign
objects.
The filter combination in the base of
the wash cabinet should be
inspected regularly and cleaned if
necessary.
Caution:
Watch out for sharp objects which
could cause injury.
Cleaning the coarse filter
^
Press the two tabs together. Remove
and clean the coarse filter.
^
Put the clean filter back in position
and press until it clicks in place.Cleaning the fine, flat and micro-fine
filters
^Remove the coarse filter.
^Remove the fine filter (if fitted) from be
-
tween the flat and the micro-fine filters.
^To unscrew the micro-fine filter, grasp
the two tabs and turn counter-
clockwise twice.
^
Remove both filters together.
^
Clean the filters.
^
Replace the filter combination in
reverse order. The flat filter must lie
flat in the base of the wash cabinet.
Machine care
43 
						

							Cleaning the non-return valve
and drain pump
If water has not been pumped away at
the end of a program, the drain pump
or the non-return valve may be blocked.
^Turn off the washer.
^Remove the filter combination from
the wash cabinet.
^Tilt the locking clamp to the side.
^
Pull out the non-return valve and
rinse under running water.The drain pump is located beneath the
non-return valve (see arrow).
^Before returning the non-return valve,
check that the drain pump is not
blocked. Spin the propeller several
times in both directions to check for
obstructions.
^Carefully refit the non-return valve
and secure it with the locking clamp.
Refit and lock the filter in place.
For safety reasons the load should
be washed again.
Machine care
44 
						

							Cleaning the filters in the water
inlet
Filters are incorporated in the screw
connection of the water inlet hose to
protect the water inlet valve. If these
filters become dirty, they need to be
cleaned, otherwise insufficient water
flows into the wash cabinet.
,The plastic housing of the water
connection contains an electrical
component. It must not be
submerged in water.
To clean the filters
^Disconnect the machine from the
main electrical supply.
^Turn off the water supply.
^Unscrew the water inlet hose.
^
Clean the large area filter,1, and fine
filter,2, replace with new filters, if
necessary.^Replace filters and the seal. Make
sure they are sitting correctly.
^Reconnect the hose to the water inlet,
making sure that it goes back on
straight.
^Open the water tap carefully.
If there is a leak, tighten the
connections.Cleaning the control panel
^The control panel should only be
cleaned with a damp cloth or a
suitable cleaner for use on plastic
materials.
,Do not use abrasive cleaners,
glass cleaners or all-purpose
cleaners! Theywilldamage the
control panel.
Cleaning the front of the
machine
^Use a cleaner suitable for the type of
material the machine front is fitted
with.
,Do not use detergents
containing ammonia or thinners.
Machine care
45 
						

							With the aid of the following guide, minor problems can be fixed without a service
call.
The Miele control unit includes a wide range of fault codes to indicate specific
errors. These fault codes are indicated on the display by a flashing F. . .  (Ranging
from F1 up to F30.) If one of these codes appears, please contact the Miele
Technical Service Department at 1-800-991-9380 for assistance.
What if … Possible fault Fix
the machine does not
start?The door is not
properly closed.Close the door firmly.
The fuse is defective
or the breaker has
tripped.Make sure the circuit breaker
has not tripped.
Fdo appears in the
display.Follow the instructions to prime
the dispensing system
(see Programming special
functions DOS 1 - 1.1.2
Priming the detergent system
and DOS 3 - 1.2.2 Priming the
neutralizer system)
a few minutes after
starting a program, the
"Fill/Drain" indicator
flashes and the fault
code "F..E" appears in
the display?–The water valves
are closed.
–
The filters in the
water inlet hose
are dirty.–Turn the program selector to
Stopf(the fault code
goes out).
–
Press the On/Off button to
turn the machine off.
–
Open the water valve or
clean the filters (see Lab
washer care).
–
Turn the machine on again
and reselect the program.
Trouble shooting
46 
						

							What if … Possible fault Fix
the wash cycle finishes
too early, the "Fill/Drain"
indicator flashes and
the fault code "F A"
appears in the display?–The drain hose is
kinked.
–The drain pump is
blocked.–Turn the program selector to
Stopf(the fault code
goes out).
–Press the On/Off button to
turn the machine off.
–Remove any kinks in the
hose. Clean the drain pump
(see Machine care).
–Turn the machine on, run the
drain program then restart
the original program (see
Operation).
water in the wash
cabinet is not heated,
the program sequence
lasts too long and the
following fault code
appears in the display:
"F01 - F03, F18, F19"?This machine has a
resettable heater
limiter, which will
switch off the heater
in case of
over-heating. This
could be caused if
large articles cover
the heating elements,
or if the filters in the
wash cabinet are
blocked.–Remove the cause of the
fault.
–Remove the service panel
(see Electrical connection).
–Press the reset button on the
temperature sensor on the
right side.
If this switch trips repeatedly,
contact the Miele Technical
Service Department before
further use. See back cover
for phone numbers.
Trouble shooting
47 
						

							What if … Possible fault Fix
I need to open the door
during a power failure?–see Opening and
closing the door.
the fault was caused by
a possible misfunction.–Turn the program
selector to Stopf
(the fault code goes
out).
–Press the On/Off
button to turn the
machine off.
–Turn the machine on
again and reselect the
program.
If there are further
difficulties, or if the fault
code "F..." appears in
the display, please
contact the Miele
Service Department. See
back cover for phone
numbers.
Trouble shooting
48 
						

							In the event of a fault which you cannot
correct yourself please contact the
Miele Technical Service Department
U1-800-991-9380
[email protected]
l1-800-565-6435
[email protected]
Please quote the model of your
machine. This information can be found
on the machine’s front panel.
After Sales Service
49 
						

							50