Miele G 7825 Manual

Cleaning the spray arms
The spray arm jets can get blocked by
particles inside them.
The spray arms should, therefore, be
checked daily.
Use a sharp pointed object to push
particles into the spray arm jets, and
rinse well under running water.
Remove the spray arms as follows:
Take any mobile units out of the wash
cabinet.
Spray arms in the wash cabinet:

Use an SW 60 spanner to loosen the
connection and then pull the spray
arm upwards or downwards.Spray arms in mobile units/modules:
Turn the nut...

Miele offer a range of branded cleaning
products. These are available from your
Miele retailer, the Spare Parts
Department, or via the internet on
www.miele-shop.com.
Cleaning the control panel
The control panel should only be
cleaned using a damp cloth or with a
proprietary cleaning agent for glass
or plastic surfaces.
An approved and listed disinfecting
agent can be used to wipe surfaces.
Do not use abrasive cleaners or
all-purpose cleaners.
Because of their chemical
composition they could cause...

Mobile units, modules and
inserts
Mobile units, modules and inserts
should be checked daily to make sure
they are functioning correctly. The
washer-disinfector is supplied with a
check list.
The following need to be inspected:
–Check that rollers on mobile units/
inserts are free of hindrance and that
they are secure.
–Check that the mobile unit connector
is at the correct height and screwed
on correctly.
– Check that the locking caps in the
module connectors of modular
system mobile units are working...

Printer (optional)
Renewing the paper roll
Renew the paper roll when the red
indicator lights up in the printer.
To do this:
Open up the front flap on the printer
and then open it downwards.
Take the empty roll together with its
spindle from the roller holder, fit the
new roll on the spindle and put back
in place.
Guide the paper upwards onto the
paper feed roller (slit behind the
colour cassette), ensuring that the
green paper feed button is kept
pressed in until the paper emerges
above the...

Repairs should only be carried
out by a suitably qualified and
trained Miele technician in
accordance with local and national
safety regulations. Unauthorised or
incorrect repairs could cause
personal injury or damage the
machine.
To avoid unnecessary service call-outs,
check that the fault has not been
caused by incorrect operation.
An overview of allerror messages
that can appear in the display are
given in the Programming manual
under "Messages".If, having followed the advice in the
operating...

Converting from steam to electric
heating or from electric to steam
If your machine is convertible, you can
use the STEAM

ELECTRO or
ELECTRO

STEAM service
programme to switch from one type of
heating method to the other.
Select STEAM

ELECTRO or
ELECTRO

STEAM (see Operation /
B. Free programme selection).
Press the Start button.
When the Service programme has
ended, a message will appear in the
display.
To
CONTINUE< press.
Converting the type of heating
56 

All electrical work must be carried
out by a suitably qualified and
competent person in accordance
with local and national safety
regulations (BS 7671 in the UK).
–Connection should be made via a
suitable isolator with an on-off switch
which is easily accessible for
servicing after the machine has been
installed.
–An electrical safety test must be
carried out after installation and after
any servicing work. It is therefore
essential that the on-off switch is
easily accessible.
– When switched off there...

This machine should be
connected to the mains water
supply and to the drainage system
in accordance with local and
national water regulations. Please
refer to the installation diagram
supplied with the machine.
–If the water supply has a high iron
content there is a danger of
corrosion occurring on items being
processed in the machine, as well as
in the machine itself.
If the chloride content of the water
exceeds 100 mg/l the risk of
corrosion to items being processed
in the machine will be further...

Height (minimum room height) 200 cm without steam condenser
240 cm with steam condenser
Width 90 cm
Depth
Depth with door open75 cm
148.5 cm
Weight (net) Approx. 505 kg
Operating weight Approx. 665 kg
Voltage, Connected load,
Fuse ratingSee data plate
Compressed air connection 600 kPa (6.0 bar) required for steam operation
Steam connection:
with electric TA
with steam TA250 - 1000 kPa / 140 - 180 °C
250 - 600 kPa * / 140 - 164 °C
Water pressure (flow rate) 200 - 1000 kPa overpressure
Water connection:...

Optional extras
–Drying unit (TA)
–Steam condenser (DK)
–Report printer (PRT)
–Dispensing systems DOS 2 and
DOS 4
–OXIVARIO kit
Water softener
If the mains water hardness level is
more than 70 mg/l (4°d), a water
softening system should be provided
on-site, such as the Miele G 7897
"Aqua-Soft system" which is effective up
to approx 720 mg/l (40°d).
Optional extras
60