Miele G 7825 Manual

Operating levels
There are four operating levels
available on this machine:
A = Fixed and free access
programmes
B = Free programme selection
C = AWK – Automatic mobile unit
recognition (programme selection
via mobile unit coding) - optional -
D = Programming / free programme
selection / change code
(see Programming Manual)
To change operating level:
Pressandat the same time.
Operating levelsABCDareshown
in the display.
Select the operating level you want
using theorbuttons.
Pressto confirm...

Starting a programme
See the Programme charts in the
Programming Manual supplied with
the machine for detailed information
and important notes on the standard
Miele programmes.
When processing medical
devices, any changes made to
programmes or dispensing systems
must be documented in a log book
kept with the machine in
accordance with the Medical
Devices directive . The machine's
cleaning and disinfecting standards
must also be re-validated.
A. Fixed programme
Set up fixed programme(s) once in...

C. AWK – Automatic mobile unit
recognition
Select operating level C.
Push the coded mobile unit into
place.
Make sure that there are no
small metallic objects or instrument
parts attracted to the magnetic strip,
in particular to the underside of it.
Any metallic objects on the strip can
result in the coding being incorrectly
read.
Close the door.
Before starting a programme it is
absolutely essentialto check that
the programme shown in the display
is the correct on for the mobile unit
being used....

Switching off
Press and release theI-0button.
Turn off the stopcocks.
Cancelling a programme
A programme can only be cancelled
in operating level B or D.
When testing to EN ISO 15883-1 or
HTM 2030 standards, the
programme must not be interrupted
or cancelled.
In operating levels B or D
Press the Stop button	.
The programme is interrupted.
CANCEL or
CONTINUE< will appear
in the display.
With established
decontamination programmes any
contaminated water must be
decontaminated using a disinfecting
agent...

Interrupting a programme
A programme can only be
interrupted in operating level B or D.
If you absolutely have to open the door,
e.g. because the load is obviously
unstable (conscious intervention):
After interrupting a DESIN
disinfection programme, if you wish
to continue it please check the
message in the display at the end of
the programme. If the message
PROCESS PARAMETERS NOT MET
is displayed, it means the door was
openedafterthe disinfection part of
the programme and the DESIN
parameters were not...

Each machine is supplied witha5m
long interface cable for data transfer
between the Profitronic system and an
external report printer or PC.
The interface cable is rolled up
inside the machine and must only be
connected by an authorised Service
Dealer or the Miele Service Dept.
The serial interface is RS 232
compatible.
For the interface configurations see
"PC/Printer Function" in the
Programming manual.
Various printers can be used as
external printers:
– Epson-compatible
(contact Miele for a...

Periodic checks
This washer-disinfector should be
inspected in accordance with local and
national safety regulations after every
1000 operating hours, or every 6
months by a Miele approved service
technician.
This maintenance will cover the
following:
–Electrical safety tests
–Door mechanism and door seal
–Any screw connections and
connectors in the wash cabinet
– Water inlet and drainage
– Internal and external dispensing
systems
– Spray arms
– Filter combination
– Sump including drain pump and...

Process validation
The standard of cleaning and
disinfection in the disinfection
programmes must be confirmed by the
user as a routine matter.
Safety checks must be carried out to
the machine every 3 months by a Miele
approved service technician in
accordance with EN ISO 15883 and
HTM 2030.
Routine checks
Before the start of each working day the
user must carry out a number of routine
checks. A check list is supplied with the
machine for this purpose.
The following need to be inspected:
–All filters in...

Cleaning the filters in the wash
cabinet
The filters in the base of the wash
cabinet are designed to prevent coarse
soiling getting into the circulation
system.
A build-up of coarse soiling can cause
the filters to clog up. They should,
therefore, be checked daily and
cleaned if necessary.
The machine must not be used
without all the filters in place.
Watch out for glass splinters
which could cause injury.Cleaning the fine filter
Remove the filter and clean it.
Cleaning the flat filter

Remove the...

Cleaning the filters for the circulation
pump
There are two filters located underneath
the flat filter to the right of the heating
element block to protect the circulation
pump.
Pull them up and out of their holders,
and clean them.
Replace the filters by carrying out the
above steps in the reverse order.
Maintenance
50