Midway Cruis N Exotica 39 Dedicated Game Operations Manual

Service - 7    
 Viewing Glass Service
To service Monitor Bezel…
Ø Switch off the power to the game machine and unplug the AC line cord.
Ø Lift open the Marquee Housing. Refer to service instructions for Marquee.
Ø Grasp the monitor bezel at the bottom and lift it out of cabinet.
Ø Perform the desired repair or equipment replacement.
Ø Wipe the bezel clean before reinstallation.
To service the Monitor (CRT)…
We recommend that you read the WARNINGS thoroughly before beginning this procedure.CAUTION
The...

Service - 8 To service the Control Cabinet…
Refer to the Control Cabinet Service illustration.
Ø Switch off the power to the game machine and unplug the AC line cord.
Ø Remove the tamper resistant screws from either side of the control cabinet used to fasten it to
the cabinet brackets in the main cabinet.
Ø Slide the control cabinet halfway back along the rails to expose wiring. Label and disconnect
all wiring.
Ø Continue to slide the cabinet away from the main cabinet until it clears the mounting...

Service - 9Dashboard Service
To service the Center Control Pod…
Refer to the Center Control Pod Service illustration.
Ø Switch off the power to the game machine and unplug the AC line cord.
Ø Remove the Dashboard. Refer to service instructions for Dashboard.
Ø Remove the steering mechanism. Refer to service instructions for steering mechanism.
Ø Disconnect the light bulbs from the sockets for both the Radio and Start buttons, and set aside.
Ø Remove 5 hex head screws that form the outline of the pod and...

Service - 10 Dashboard PCB Service, continued
Ø Perform the desired repair or equipment replacement.
Ø Connect the ribbon and power cable to a Dashboard PCB. NOTE: The red stripe on the ribbon
cable must be lined up with pin 1 on the PCB, and the black wire on the power cable must line
up with pin 1 on the power connection for the Dashboard.
Ø Reattach the PCB to the pod, and then fasten the pod to the dashboard.
Ø Check for pinched wires.
Ø Reinstall the Dashboard and fasten in place with the screws...

Service - 11Control Pod, Buttons and Shifter Service
To service View Buttons…
Refer to the Control Pod, Buttons and Shifter Service illustration.
Ø Switch off the power to the game machine and unplug the AC line cord.
Ø Remove the 4 tamper-resistant buttons used to fasten the faceplate.
Ø Pull the plate forward enough to expose the switches.
Ø Label and disconnect the wiring for the pod(s) being serviced.
Ø Lift assembly completely out of the pod and set aside.
Ø Perform the desired repair or equipment...

Service - 12 To service Steering Assembly…
Refer to the Steering Assembly Service illustration.
Ø Switch off the power to the game machine and unplug the AC line cord.
Ø Remove the Dashboard. Refer to service instructions for Dashboard.
Ø Remove 6 screws used to fasten the cover plate to the center of the steering wheel. Remove
the cover plate and set aside.
Ø Remove the 3 screws used to fasten the wheel hoop to the shaft. Pull the wheel hoop off of the
dashboard.
Ø Remove 4 flange nuts holding the motor...

Service - 13 Keypad Service, continued
Ø Lift the keypad out.
Ø Perform the desired repair or equipment replacement.
Ø Reinstall keypad, seat the spacers and fasten in place with the nuts provided.
Ø Reinstall Dashboard and fasten with hardware provided.Keypad Service
To service Control Cabinet Speaker…
    This speaker is located just above the pedal assembly.
Ø Switch off the power to the game machine and unplug the AC line cord.
Ø Remove the Control Cabinet. Refer to service instructions for Control...

Service - 14 To service Coin Meter…
Ø Switch off the power to the game machine and unplug the AC line cord.
Ø Unlock the cash door and swing it open.  Remove the cash tubs.
Ø The meter is located on a plate at the vault bottom.  Remove the screws and lift the plate just
enough to disconnect the meter wires from the harness.
Ø Record the meter count before testing or replacement.
Ø Perform the desired repair or equipment replacement.
To service Coin Mechanism…
Ø Switch off the power to the game machine...

Service - 15 To service CPU Board Assembly…
Ø Switch off the power to the game machine and unplug the AC line cord.
Ø Unlock and remove the rear door.
Ø Remove the perforated metal cover to expose the CPU Board Assembly.
Ø Carefully note the orientation of the JAMMA connector and the other cables.  Extract the
harness and other cables from the board connectors.
Ø Remove CPU board assembly mounting screws.  Lift the board out of the cabinet and set in a
safe place.  Use anti-static bags and protective...

Service - 16 To service the Power Supply…
Ø Switch off the power to the game machine and unplug the AC line cord.
Ø Unlock and remove the rear cabinet door.
Ø Unplug the IEC AC connector from the rear of the supply and the DC connector from the front.
Ø Remove the two front and two rear screws from the supply, then lift it off of the power chassis.
Note voltage setting.
Ø Perform the desired repair or equipment replacement.
Ø Be sure to set the voltage switch to the correct value prior to...