Midway Cruis N Exotica 39 Dedicated Game Operations Manual

Troubleshooting - 11 BELTTENSION BOLTMOUNTING NUT
LOOSEN 
MOUNTING 
NUTS TO 
ADJUST BELT 
TENSIONHow to Adjust Belt TightnessPlayer Panel Controls 

Troubleshooting - 12 Video Troubleshooting Table
SYMPTOMCAUSEREQUIRED ACTIONPower problemVerify connection of AC Power to video monitor.
Inspect neck of CRT in dim light. Glowing
filament near CRT base confirms monitor circuits
receive power. However, voltages or signals may
not be normal.Faulty wiring1. Turn off game power. Verify that video signal and
Remote Adjustment Board connectors seat
properly on Video Monitor Board.
2. Assure that no wires are caught on chassis or
mounting brackets.Improper...

Troubleshooting - 13CAUTION
Do not remove or install any connector when power is turned on. Installation under
power will damage the circuit boards or ROM’s and void the warranty.WARNING: HIGH VOLTAGE.
Video Game Machine (VGM) monitors generate and store potentially lethal high
voltages. Avoid touching any part of the monitor until power has been off for some time.
A picture tube can maintain a hazardous charge for up to several days. Only qualified
technicians should service monitors. Turn off the...

Troubleshooting - 14 Video Troubleshooting, continued
SYMPTOMCAUSEREQUIRED ACTION· White areas at screen edges
appear tinged with color
· Dots at screen edges appear
ovoid or cylindricalPicture tube dynamic
convergence is out of
alignmentHave service bureau dynamically re-converge
monitor. This procedure requires removing and
repositioning yoke. Service bureau must follow
instructions from monitor manufacturer.Faulty wiring1. Check connectors and cables for wiring
continuity. Video cables connect circuit...

Troubleshooting - 15 Video Troubleshooting, continued
SYMPTOMCAUSEREQUIRED ACTION· Picture is too narrowMaladjusted WIDTH
potFrom Diagnostic Menu select MONITOR TEST.
Watch Crosshatch Screen while adjusting
WIDTH pot for best picture. You’ll find this pot on
Monitor Remote Control Board, behind coin door.· Picture is too shortMaladjusted HEIGHT
pot or damaged
vertical circuit1. From Diagnostic Menu select MONITOR TEST.
Watch Crosshatch Screen while adjusting
HEIGHT pot for best picture. You’ll find this...

Troubleshooting - 16 Audio Troubleshooting Table
SYMPTOMCAUSEREQUIRED ACTIONImproper volume
settingPress and hold TEST MODE switch inside coin
door to enter Menu System. Select VOLUME
MENU from the Main Menu. Make sure the
Attract Music is on (enabled). Verify all volume
levels are set well above zero. If necessary,
change levels to make game audible.Faulty wiringTurn off power. Assure wiring harness
connectors attach and fully seat onto mating
board connectors. Verify harness connects to
CPU Board....

Troubleshooting - 17 Audio Problems, continued
SYMPTOMCAUSEREQUIRED ACTIONFaulty speaker1. From Diagnostics Menu, choose SOUND TEST.
Recheck speakers with audio signals provided
by test.
2. Verify proper speaker operation by connecting
speaker in question to working Video Game
Machine (VGM).· Dead sound channel
Faulty circuit boardRun power-up self-test sequence. Note errors
found during tests. Compare CPU Board LED’s
with LED Indicator Status Charts. Note
discrepancies.Faulty wiring1. Check cabinet...

Troubleshooting - 18 Miscellaneous Problem Troubleshooting Table
SYMPTOMCAUSEREQUIRED ACTIONFaulty fluorescent
tube1. Remove fluorescent tube from sockets. If you
find cracks or darkened ends, install new lamp.
Clean tube.
2. Check continuity of both fluorescent tube
filaments.
3. Check lamp ballast is rated for local AC line
voltage and frequency.
4. Verify fluorescent tube operates by placing it in
working VGM.Faulty lamp fixture1.
2.Verify lamp pins make good connection with
socket contacts.
Check the...

WARNINGS & NOTICES
WARNING
· Use of non-MIDWAY parts or circuit modifications may cause serious injury or equipment damage!
· Substitute parts or modifications may void EMC directive or FCC type acceptance.
· This game is protected by federal copyright, trademark and patent laws.  Unauthorized modifications may be
illegal under federal law.  This also applies to MIDWAY logos, designs, publications and assemblies.  Moreover,
facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under...