Metz Puros 37 Ml Operating Instructions

							81
• Use the - +key to select the desired scope of
operation and press the OK key to save the
new setting.
2 & & & 
This menu permits you to configure the
use of the TV set to a certain degree.
All of the functions listed for the 1&
menu are available and are supple-
mented by the following functions:
- Childlock
- Timer control (sleep timer)
- Automatic station search
- Transfer of the TV station
table from the TV set to a
Data Logic video recorder.
- Editing functions in the sta-
tion table
3 & & & 
This is the opera-
ting scope for per-
sons who are inter-
ested in technology
who want to be
able to use the full
range of functions
of the TV set.
Setting the scope of operation
• Press the MENU key to open the TV menu.
• Press the red key  to open the menu Confi-
guration.
• Use the cursor control key to move to the
menu line Initial programme position.
• Press the numeric key 
to select Scope of
operation.
• In the setting window, use the 
-+
key to select
the desired scope of operation.
Press the OK key to save the new setting.
Press the EXIT key to close the TV menu.
29. Scope of Operation
MENU

OK
EXIT
Opening the menu
The number of subjects and sections depends
on the selected scope of operation. Depending
on the configuration of the TV set, the various
menu items may be displayed in a different
order and numbered differently.
Data Logic adjustm.
EPG settings
Operating
Sound settings
HiFi output
2)
Init. prog.position
AV function
Function for F3
Function for F2
Function for F1
EURO sockets
DVB-T
Analog-TV
Country
Language
Operating
Configuration
Change with
Accept value with    .–   +OK
F1➔
Operating full
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 81
 
						

							82
30. Operation without the 
Remote Control
Operation without the remote control is provided
as an emergency measure in case the batteries of
your remote control are exhausted or the remote
control is not readily available.
The local controls and the power switch are loca-
ted on the left side at the back of the TV set.
Switching on
Press the main power switch on the TV set. After
about five seconds, the TV set is switched on with
programme position 1 or the programmed initial
programme position selected.
You can also use the following functions directly
on the TV set, without a remote control. For func-
tions which require further adjustments, the func-
tion remains preselected for ten seconds.
Programme selection
Press the -/+buttons.
Volume
Press and hold the preselection key Funtil the bar
display for the volume appears on the screen. Then
press the - or + button to adjust the volume.
Contrast
Press and hold the preselection key Funtil the bar
display for the contrast appears on the screen. Then
press the - or + button to adjust the contrast.
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 82
 
						

							83
When receiving a dual-language pro-
gramme, you can switch between the
two sound channels.
In TV mode, press and hold the yellow
key  until the sound function Sound
mode is selected.
Then use the 
-+
key to select Sound 1
or Sound 2.
32. Sound 1, Sound 2
Headph. Vol.
Sound mode Cannel 2
Spatial
Spatial 
Sound mode Cannel 2
Balance 
31. Connecting Headphones
The headphone socket is located on the right side
at the back of the TV set.
Tilt the flap on the Milos up with your fingernail.
On the Puros or Talio open the flap by 
pressing •••.
See also ch. 34.
We recommend the use of headphones with an
impedance of at least 32 Ω. The use of headpho-
nes with a lower impedance will reduce the dyna-
mic range of the sound.
You can save the headphone volume as a stan-
dard value.
Setting the volume too high when using
headphones or earphones can result in
damage to the ears - including the com-
plete loss of hearing.
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 83
 
						

							84
33. Cleaning the TV Set
Before cleaning the set, always switch it off
with the mains switch!
Incorrect treatment and cleaning of the screen sur-
face can cause irreparable damage to it. You
should therefore always observe the following
instructions for treatment and cleaning of the set.
T
reatment:
Always treat the screen surface very carefully.
Take care not to damage it mechanically by
shocks, impact, scratching or scraping.
Keep sharp, pointed and hard objects away from
the surface of the screen.
Keep the surface of the screen clean.
For cleaning the case and the screen, use only a
soft, dry cloth. For removing stubborn marks, you
may moisten the cloth slightly.
Cleaning and care:
The surface of the screen may be cleaned only
with a soft, dry cloth (such as a microfleece
duster). If any marks cannot be removed with this
dry cloth, you may moisten the cloth slightly.
Take care that no water or other liquid can enter
the TV set, since this can cause serious damage to
the set.
If any liquid or other foreign object (pieces of
metal, etc.) enters the set, immediately disconnect
the mains plug from the wall outlet.
Never insert your hands or tools into the set, since
this may result in electric shocks.

607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 84
 
						

							85
34. Connections
 S-VHS or. Y/C in (e.g. camcorder)
 FBAS/Video in (e.g. digital camera or camcorder)
 Audio in   R/L (e.g. camcorder)
( Headphone socket, diameter 3.5 mm
(  
right side

Service socket for
use by your dealer
Antenna socket
35. Connectionson the rear side
Viewed from below
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 85
 
						

							86
35. Connections on the Rear of the Set
(covered by a flap)
Viewed from below
With the aid of an optical audio cable (Toslink cable, available from your
dealer), the digital audio signal (AC3) provided by the TV set can be extracted
for external processing.
HDMI connector 
Signal type
HDMI 
(Video/Audio
digital IN)
OUT
Digital
Audio
Power connection
Video IN
YCbCr in
YUV in
OUT
Audio
EURO sockets for connection of
external AV devices
Video and audio IN/OUT
Video IN 
DVI-I connector 
Signal type DVI-D
(Video analog)
+Video IN 
DVI-I connector 
Signal type
DVI-YUV 
(Video digital)
Audio IN
DVI-I connector 
+
IN
Audio
IN
Centre loudspeaker 
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 86
 
						

							87
35.1 Connecting a Hifi Amplifier/AV Receiver
Metz LCD-TV
HiFi-amplifier
AV-Receiver

Digital audio signal formats (depending on the source)
analogue audio signal R+L (stereo)
!Centre IN is always possible if the AV receiver offers this.
Can be used in combination with or if this option is available.
It is always possible to use the TV speakers as the centre speaker if the AV receiver
has this output available. The advantage of this is that the TV speakers can be used
as the centre speaker, thus making it unnecessary to set up an external centre spea-
ker.!
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 87
 
						

							88
35.1 Connecting a Hifi
Amplifier/AV Receiver
Registering the AV Device with the TV
• Enter the TV menu by pressing MENU.
• Press the yellow key  to open the AV Devices
menu.
• Use the cursor control key to select Hifi
Amplifier in the device selection.
• Press OK twice, use the cursor control key to
select Signal Types, and press OK..
• For connection type , select the signal type
Signal IN - SPDIF“.
For connection type , select the signal type
Signal IN – Stereo.
Confirm the setting by pressing OK
• Press the EXIT key to close
the TV menu.
Sound:
• To configure the sound set-
tings of the LCD TV, press
the yellow key and use
the cursor control key  to
select the menu item Sound
via .... 
• For connection type , use
the  
-+
key to select Sound
via Hifi
.
The speakers of the LCD TV are muted. The sound
(AC3 or stereo sound) is rendered over the spea-
kers of the Hifi set.
• For connection type , use the
-+key to select
Sound via surround.
The speakers of the LCD TV are used as the centre
box. The sound (AC3 or stereo sound) is rendered
over the speakers of the Hifi unit.
MENU
Opening the menu
OKOK
OK
EXIT
Connect as follows:
HiFi amplifier     Stereo         no signal     Cinch
Name
Signal types
connect
HiFi amplifier
AV-Receiver
Other device 2
Other device 1
PC
Satellit / set top
DVD Player 2
DVD Player 1
DVD/Videorec.2
DVD/Videorec.1
F1➔
select
connect
and clearOK
✗
AV devices
HiFi➔➔
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 88
 
						

							89
36. Copying between AV Devices
Direct recording
Opening the menu
If you wish to copy a recording from one of the
AV devices connected to your TV set (such as a
DVD player) to another connected AV device (such
as a video recorder), you must do this by means
of a direct recording operation. In this case, the
signal arriving at one of the EURO sockets is redi-
rected to the other EURO socket, from where it
can be recorded.
Example: you have a DVD player and a
video recorder connected to
the EURO sockets of the TV set
(see Section 25).
Programming a direct recording for
copying:
• Press the AV key and use the corres-
ponding numeric key to select the
DVD player (playback device).
• Press the F2key.
Briefly pressing F2executes the func-
tion which is programmed for this function key
(see Section 18., Programming function keys).
Pressing and holding F2for about three seconds
displays all functions available for this function
key.
• Press numeric key
to open the
timer menu. The timer window dis-
plays the AV programme position
(DVD player), the current date and a
time window of two hours.
• If two hours is insufficient for the
copying operation, use the numeric
keys to enter a later end time.
F2

2DVD-Player
1Videorecor-
der
AV

Recording Yes
Reminder No
Pr   6
SAT 1
Date 01.05.
Start 22:45
End 23:40
VPS no
Recording device
Videorecorder
Change with
:select
:save the timer
OK
Select with...
or       .
Confirm with      .
OK
–   +
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 89
 
						

							90
• Use the cursor control key to select the line
Recording device.
If only one such device exists, it is then display-
ed. If further recording devices exist, you can
select the desired device with the aid of 
the 
-+
key.
• Press the OK key to save the settings.
• On the playback device (in this example, the
DVD player) start the film which is to be copied.
• On the recording device (in this example, the
video recorder), select the AV programme posi-
tion (in most cases AV1).
• On the recording device, start a direct recor-
ding by pressing the appropriate button (RECor
OTR, etc.).
The TV set is now set up so that the signal coming
from the playback device is connected directly to
the recording device.
36. Copying between AV Devices
Direct recording
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 90