Metz Clarus 32 Ml Operating Instructions
Have a look at the manual Metz Clarus 32 Ml Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 5 Metz manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
71 25. Registering AV Devices Data Logic Opening the menu • Press numeric key , use the - +key to select the correct signal types (OUT/IN) and press the OK key. (See also the operating instructions of the AV device.) • If desired, press numeric key , enter a new name for the AV device and press the OK key. • Use the cursor control key to select Data Logic and press the OK key. • Use the cursor control key to select Connect and press the OK key. Then connect the AV device to the corresponding EURO socket. Note: In the menu Configuration in the menu point Data logic settings Mode1 is set. This factory setting is valid for most AV devices. Should the AV device break off the recording after about 5-10 secs, select the setting Mode 2. Data Logic: transferring the station table • Press the MENU key to open the TV menu. • Press the red key to open the menu Configura- tion. • Press numeric key to select Analogue TV. • Press the OK key and then press numeric key ! to select Data Logic. • Press the OK key to transfer the programme positions from the TV set to the video recorder. OK EXIT MENU ! OK The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. Start data transfer Programme position DataLogic Terrestrial station search Search settings2) AV function Function for F3 Function for F2 Function for F1 EURO sockets DVB-T Analog-TV Country Language Operating Configuration Change with Start data transfer with . OK F1➔ – + 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 71
72 The signal type always refers to the input and output of the AV device. Some AV devices may use a composite video sig- nal (FBAS) for recording and playback operations and an RGB signal for displaying their menus. It is not possible to make a general statement in this respect. The operating instructions of the AV device concerned may provide some indication. If you connect such an AV device with the signal type composite video (FBAS) and recordings are played back correctly, but you cannot see the menu of the AV device, you must change the sig- nal type in the menu AV devices to RGB. Setting the signal type • Press the MENU key to open the TV menu. • Press the yellow key to open the menu AV devi- ces. • Use the cursor control key to select the AV device whose signal type you wish to change and press the OK key. • Press numeric key , use the cursor control key to select Signal OUT, and use the - +key to change the setting to RGB. • Press the OK key to confirm your selection. • Press the EXIT key to close the TV menu. 25. Registering AV Devices Setting signal types RGB MENU OK OK EXIT Opening the menu Caution ! This may cause an existing connection diagram to be modified. If so, you must reconnect the AV devices accordingly. Signal OUT RGB Signal IN CVBS DataLogic Name Signal types connect HiFi amplifier AV-Receiver Other device 2 Other device 1 PC Satellit / set top DVD Player 2 DVD Player 1 DVD/Videorec.2 DVD/Videorec.1 F1➔ ✗ AV devices Change with Accept value with .OK– + 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 72
73 25. Registering AV Devices Setting signal types DVI/HDMI The signal type always refers to the input and output of the AV device. AV devices equipped with a DVI or HDMI socket can be connected to the LCD TV with the aid of a DVI or HDMI cable, respectively. The connected device must be registered in the menu AV devi- ces with Signal OUT set to DVI or HDMI, as applicable. Connection via a DVI or HDMI interface permits digital transfer of the picture sig- nal from the device to the TV set. Bei When using DVI, the sound must be connected by means of a cinch cable. When using HDMI, the sound is also output over the HDMI socket. Setting the signal type DVI or HDMI • Press the MENU key to open the TV menu. • Press the yellow key to open the menu AV devi- ces. • Use the cursor control key to select the AV device whose signal type you wish to change and press the OK key. • Press numeric key , use the cursor control key to select Signal OUT, and use the - +key to change the setting to RGB. • Press the OK key to confirm your selection. • Press the EXIT key to close the TV menu. Caution ! This may cause an existing con- nection diagram to be modified. If so, you must reconnect the AV devices accordingly. MENU OK OK EXIT Opening the menu Caution ! This may cause an existing connection diagram to be modified. If so, you must reconnect the AV devices accordingly. Signal OUT HDMI Signal IN no Signal DataLogic Name Signal types connect HiFi amplifier AV-Receiver Other device 2 Other device 1 PC Satellit / set top DVD Player 2 DVD Player 1 DVD/Videorec.2 DVD/Videorec.1 F1➔ ✗ AV devices Change with Accept value with .OK– + 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 73
74 Connection of external devices with YUV compo- nent output to the COMPONENT IN RCA jacks. The signal type always refers to the input and output of the AV device. AV devices equipped with a YUV jack can be con- nected to the LCD TV by means of a YUV cable (see page 86). In the AV Devices menu, the con- nected AV device must be registered with signal OUT YUV. Setting the YUV Signal Type - Enter the TV menu by pressing MENU. - Press the yellow key to open the AV Devices menu. - Use the cursor control to select the AV device whose signal type you want to change and press OK. - Press numeric key , use the cursor control to select Signal OUT, and use the - +key to set YUV. - Confirm the setting by pres- sing OK. - Exit the TV Menu by pres- sing EXIT. MENU OK OK EXIT Opening the menu 25. Registering AV Devices Setting signal types YUV Caution ! This may cause an existing connection diagram to be modified. If so, you must reconnect the AV devices accordingly. Signal OUT YUV Signal IN no Signal DataLogic Name Signal types connect HiFi amplifier AV-Receiver Other device 2 Other device 1 PC Satellit / set top DVD Player 2 DVD Player 1 DVD/Videorec.2 DVD/Videorec.1 F1➔ ✗ AV devices Change with Accept value with .OK– + 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 74
75 25.1 Removing AV DevicesOpening the menu The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. This menu item is not available in a 2 ** menu. If desired, you can change the factory settings for AV devices (a video recorder on the EURO1 socket and a DVD player on the EURO2 socket). Removing an A V device from the TV set • Press the MENU key to open the TV menu. • Press the yellow key to open the menu AV devices. • Use the cursor control key to select the device you wish to remove and press the OK key. The cursor is on the line Connect. • Press the OK key again. A message is displayed, asking if you really want to change the connected devi- ce. • Press the OKkey again to remove the connected devi- ce. • Press the EXIT key to clo- se the TV menu. Connect as follows: DVD/Videorec.1 DataLogic Name Signal types connect HiFi amplifier AV-Receiver Other device 2 Other device 1 PC Satellit / set top DVD Player 2 DVD Player 1 DVD/Videorec.2 DVD/Videorec.1 F1➔ select connect and clearOKVCR AV devices MENU EXIT OK OK 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 75
76 You can define an initial programme position in this TV set. This initial programme position is used primarily to select the AV programme position if you use an external receiver. Setting the initial programme position This menu item is not available in a 2 ** menu. Select a receiver (satellite or set-top box) in the menu AV devices and connect the receiver to the TV set (see also Section 25, Registering AV Devices). • Press the AV key. • Use the numeric keys to select the position Sat/Set- top in the AV menu. • Press the MENU key to open the TV menu. • Press the red key to open the menu Configuration. • Use the cursor control key to select Operation and then Initial programme posi- tion. • Press the OK key and, in the setting window, use the -+ key to select Yes. • Press the OK key to save the new setting. • Press the EXIT key to close the TV menu. The AV programme position will now be selected automatically when you switch on the TV set with the main power switch. 26. Initial Programme PositionOpening the menu MENU OK OK OK EXIT The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. 2) Possible only on sets equipped with this function. Betriebsart AV Programm Satellit/set top Data Logic adjustm. EPG settings Operating Sound settings HiFi output 2) Init. prog.position AV function Function for F3 Function for F2 Function for F1 EURO sockets DVB-T Analog-TV Country Language Operating Configuration Change with Accept value with .– +OK F1➔ 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 76
77 MENU The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. 27. Sound via HiFi Amplifier HiFi output On the rear of the TV set, you will find audio sockets and a digital audio-out socket (see page 86) which can be used to connect the TV set to a HiFi system (HiFi amplifier). Settings need to be made in the menu items HiFi output and Sound settings only if the TV set is connected to a HiFi system. If you want adjust the sound settings exclusively on the HiFi system, you must set the HiFi output to constant. You can then no longer adjust the volume and tone with the Metz remote control. The mute function remains active. If you want to be able to chan- ge the sound settings with the Metz remote control, you must set the HiFi output to variable. Setting the HiFi output • Press the MENU key to open the TV menu. • Press the red key to open the menu Configuration. • Use the cursor control key to select Initial programme position. • Use the corresponding numeric key (in the example: ) to select HiFi output. • In the setting window, use the -+ key to set the desired parameters. • Press the OK key to save the new settings. • Press the EXIT key to close the TV menu. In normal TV Mode, the function Sound via... can be activated temporarily by pressing the yel- low key and using the -+ key. Opening the menu OK EXIT Data Logic adjustm. EPG settings Operating Sound settings HiFi output 2) Init. prog.position AV function Function for F3 Function for F2 Function for F1 EURO sockets DVB-T Analog-TV Country Language Operating Configuration Change with Accept value with .– +OK F1➔ HiFi output constant Output level 50% 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 77
78 On the rear of the TV set, you will find audio sockets and a digital audio-out socket (see page 81) which can be used to connect the TV set to a HiFi system (HiFi amplifier). If you wish to play back the sound only via a HiFi system (HiFi amplifier) which is connected with the aid of a Cinch cable, you must select the function Sound via HiFi. If you wish to play back the sound only via a HiFi system (HiFi amplifier) which is connected with the aid of an optical audio cable (Toslink, available as an accessory), the follo- wing settings should not be made. Setting sound via HiFi • Press the MENU key to open the TV menu. • Press the red key to open the menu Configuration. • Press the OK key to move to the right-hand column. • Use the cursor control key or the corresponding nume- ric key (in the example: ) to select Sound settings. • In the setting window, use the cursor control key to select the menu item Sound via…. • Use the -+ key to select Sound via HiFi. • Press the OK key to save the new setting. • Press the EXIT key to close the TV menu. In normal TV Mode, the function Sound via... can be activated temporarily by pressing the yel- low key and using the -+ key. 27. Sound via HiFi Amplifier HiFi output Opening the menu MENU OK ! OK EXIT The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. 2) Possible only on sets equipped with this function. Data Logic adjustm. EPG settings Operating Sound settings HiFi output 2) Init. prog.position AV function Function for F3 Function for F2 Function for F1 EURO sockets DVB-T Analog-TV Country Language Operating Configuration Change with Accept value with .– +OK F1➔ Mute (two-stage) on Sound via HiFi 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 78
79 Opening the menu28. DVB Radio Mode For DVB radio operation, the TV set must be converted with a DVB-S or DVB-C modu- le (see also chapter 39.1 Upgrade Options). To switch from TV mode to DVB radio mode, press the R key. The screen is automatically blanked after about 30 seconds. To switch from DVB radio mode to TV mode, press the TV key. Setting DVB radio stations The available DVB radio stations are automatical- ly detected during a station search (see Section 22) and stored in a separate station table at the operating level for radio mode. The radio station table can be sorted (see Section 24) and the station logos can be changed (see Section 23). DVB radio stations are administered in the same basic way as DVB TV stations. The functions described in Sections 12, 12.1, 15 to 17.2 and 18 (Special functions, Normal/speech, Timer over view and Direct recording) are also available for radio sta- tions. Note: With the blue key , the screen can be switched on and off manually. R TV 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 79
80 29. Scope of Operation The adjustable scope of operation for the TV set can be a great help in finding your way around the complex operating functions of the TV set. The scope of operation can be set to various levels, which are identified by asterisks. 1 & & & Just watching TV- in other words, it is not possible to open the TV menu and only the functions available on the remote control can be used: - Zapping - Selection of programme positions with the nume- ric keys, the oval P+/P- rocker key or the white key . - Opening Teletext. - Displaying help information (INFO). - Playing back films from a video recorder or DVD player by pressing the AV key. - Selecting Special functions 1 by pressing the F1key. - Selecting Special functions 2 by pressing the F2key. - Selecting Special functions 3 by pressing the F3key. - Selecting connected AV devices by pressing the AV key. - Calling the standard picture functions by pres- sing the blue key . - Calling the standard sound functions by pressing the yellow key . - Calling the EPG function with the EPG key. If the scope of operation is set to a 1& menu and you subsequently want to open a menu, then: • Press and hold the MENU key for at least five seconds to open the TV menu. • The menu item Operation is automatically selected. 607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 80