Marantz Vp10s1 DLP Projector User Manual

27
ENGLISH
Picture quality can be fine-adjusted from the Fine Menu.
Note: Some menu items cannot be adjusted depending on the input signal.
❖Luminance
H Detail Gain(Horizontal Detail Processing Gain)
: Sets the degree of detail enhancement in the horizontal direction.
H Detail Threshold(Horizontal Detail processing Threshold)
: Sets the minimum luminance signal level accepted for horizontal detail gain processing.
H Edge Gain(Horizontal Large Edge Enhancement Gain)
: Sets the contour enhancement level in...

28
ENGLISH
❖Sub Control
Contrast Red
: Sets how much red contrast comes out in images.
Contrast Green
: Sets how much green contrast comes out in images.
Contrast Blue
: Sets how much blue contrast comes out in images.
Brightness Red
: Sets how bright red comes out in images.
Brightness Green
: Sets how bright green comes out in images.
Brightness Blue
: Sets how bright blue comes out in images.
Clamp Position
: Sets the clamp position.
Clamp Width
: Sets the clamp width.
❖Miscellaneous
DCDi
: Turns the...

You can make the following settings.
Lamp Mode High / Low
High Bright On, Off
High Bright On : Display brightest image.
Aspect Full, Normal, Zoom, Through
OSD Position 16:9, 4:3, Through
VCR Mode On, Off
Cinema Auto, Off
Cinema mode: 2-3 pulldown for NTSC, 2-2
for PAL
Black Setup 0IRE, 7.5IRE 
/NORMAL, EXPAND (For DVI input)
Adjusts black level to the source.
–OSD Position
You can select from three positions: 16:9, 4:3 and Through.
–VCR Mode
On : Stabilizes the picture. Use to play back video or input TV...

You can make the following settings.
Component 1Auto, NTSC, PAL, 480p, 540p, 576p,
720p, 1035i, 1080i
Component 2Auto, NTSC, PAL, 480p, 540p, 576p,
720p, 1035i, 1080i
S-Video Auto, NTSC, PAL, SECAM
Video Auto, NTSC, PAL, SECAM
RGB Auto, NTSC, PAL, 480p, 540p, 576p,
720p, 1035i, 1080i
DVI RGB, YPBPR, YCBCR
Sets the color space conversion for DVI
input.
RGB: Does not convert color space.
YP
BPR: Suitable for high definition TV
signals such as 720p and 1080i.
YC
BCR: Suitable for signals such as 480p
and...

31
ENGLISH
You can make the following settings.
–Keystone V / H
Corrects the trapezoidal shape of the projected image. (For details, “Keystone Correction” 
pg. 19.)
–Auto Adjust
Use this mode for RGB input when RGB System on the System menu is set to “Auto”.
Yes : The Picture Shift V/H, vertical/horizontal resolution and Phase of the RGB signal are set automatically.
No : Disables automatic image adjustment. Set Picture Shift V/H, Size V/H and Phase yourself.
Select “Yes” with the 
1and 2buttons and...

You can configure the projector from the following settings.
–Auto Power Off
When the auto power off feature is turned on, the below message appears on the screen if no signals are received and no
operations are performed for 9 consecutive minutes. Power to the projector then shuts off automatically if the situation
continues for another minute.
About 1 minute after the message appears on the screen, power to the projector shuts off.
Note:
After the above message appears on the screen, pressing any...

33
ENGLISH
–Reset All
Resets all settings to their factory defaults except the user-selected gamma curve and the lamp life counter. When you select
“Yes”, the following message appears on the screen.
Select “Yes” and press the ENTERbutton.
❖How to Operate the Config Menu
1.Select the desired menu item and press the 2button.
The setting item will appear on the screen.
2.Use the 3and 4buttons to set the item.
3.Press the 1button to enter the setting and return to menu item selection.
You can turn the...

34
ENGLISHYou can select a picture mode from the MENU screen. This projector offers 4 pictures modes: Theater, Standard, Dynamic and
User. Moreover, each of these picture modes has 3 indexes for saving picture quality adjustments.
•Theater  : Reproduces the kind of black suited for movie software.
•Standard  : Suited for normal movie software.
•Dynamic  : Suited for visually dynamic movie software.
•User : Enables you to adjust the gamma curve as preferred.
Note: Each picture mode has 3 indexes (1, 2 and...

35
ENGLISH❖Lamp Life
Pressing the INFO.button on the remote controller displays the below message on the screen. 
The remaining lamp life appears on the second from last line.
Note:
•The lamp lasts a maximum of 1,500 hours. Although every possible effort has gone into quality, the lamp can – though rarely -
burn out after 1,000 hours of lighting. Therefore, it is recommended to replace the lamp promptly when lamp life falls under 500
hours. The lamp must not be used in excess of the maximum lamp life....

36
ENGLISH
❖Resetting the Lamp Life Counter
The lamp lasts a maximum of 1,500 hours. The projector is
designed to shut off power if the lamp is used beyond this
1,500 hours. In such case, replace the lamp and reset the lamp
life counter as follows.
1.After the “Lamp Life 0 Hours” message appears on the
screen, power to the projector shuts off. Promptly replace
the lamp with a new one. (See “Lamp Unit Replacement”
pg. 36.)
2.After replacing the lamp, press either the POWERbutton
on the projector or the...