Marantz Pd4201 User Guide

32
Reducing image retention
The brightness of the screen, the position of the picture,
positive/negative mode and screen wiper are adjusted to
reduce image retention.
Set “ADVANCED OSM” to “ON” in the FUNCTION menu.
On “PDP SAVER” of “FUNCTION” menu, select
“MANUAL”, then press the MENU/ENTER button.
The “PDP SAVER” screen appears.
Set “ADVANCED OSM” to “ON” in the FUNCTION menu.
On “PICTURE FREEZE” of “FUNCTION” menu, select
“BTM LEFT”.
SEL. ADJ. RETURNEXIT
FUNCTION
ADVANCED OSM
POWER MGT.
INPUT SKIP...

33
INVERSE/WHITE
Use this to set the inverse mode or to display a white
screen.
Example: Setting “INVERSE/WHITE” to “WHITE”
On “INVERSE/WHITE” of “PDP SAVER” menu, select
“WHITE”.
SEL. ADJ. RETURNEXIT
PDP SAVER
PEAK BRIGHT
ORBITER
INVERSE/WHITE
SCREEN WIPER
SOFT FOCUS
OSM ORBITER
OSM CONTRAST:   100%
:   AUTO1
:   WHITE
:   OFF
:   OFF
:   ON
:   LOW
Information

 INVERSE/WHITE Settings
OFF: Inverse/white mode does not function.
INVERSE: The picture is displayed alternately between
positive image and...

34
Reducing the brightness of Closed Caption
Use this to reduce the brightness of Closed Caption.
Example: Setting “NORMAL”
Set “ADVANCED OSM” to “ON” in the FUNCTION menu.
On “CAPTION CONT” of “FUNCTION” menu, select
“NORMAL”.
SEL. ADJ. RETURNEXIT
FUNCTION
ADVANCED OSM
POWER MGT.
INPUT SKIP
SUB. PICTURE
ZOOM NAV
PICTURE FREEZE
PDP SAVER 
CLOSED CAPTION 
CAPTION CONT 
PWR. ON MODE:   OFF
:   OFF
:   OFF
:   BTM LEFT
:   S BY S1
:   MANUAL 
:   OFF
:   NORMAL
Information

 CAPTION CONT settings
NORMAL:...

35
Application
These specifications cover the communications control of
the plasma monitor by external equipment.
Connections
Connections are made as described below.
Connector on the plasma monitor side: EXTERNAL
CONTROL connector.
Use a crossed (reverse) cable.
Type of connector: D-Sub 9-pin male
15
9
62
34
78
Communication Parameters
(1) Communication system Asynchronous
(2) Interface RS-232C
(3) Baud rate 9600 bps
(4) Data length 8 bits
(5) Parity Odd
(6) Stop bit 1 bit
(7) Communication code Hex...

36
Following is the connection example of STB (Set-top Box)
using the REMOTE IN/OUT connectors of the plasma
monitor. Consult your dealer about the actual connection
and operation.
* Connection Example
• STB has the REMOTE IN connector.
• The pin assignment of the REMOTE IN connector of
STB is same as that of 1/8 stereo mini cable connected
to the REMOTE OUT connector (Page 35).
• The transmit frequency of the remote control of STB is
37.9 kHz (Typical).
* The 1/8 Stereo Mini cable must be purchased...

37
Remedy
• If there are no abnormalities in the image and sound,
the noise is caused by the cabinet reacting to
changes in temperature. This will not affect
performance.
• Leave some space between the display and the
connected components.
• Replace both batteries with new ones.
• Plug the monitor’s power cord into a power outlet.
• Press the power button on the monitor to turn on the
power.
• Replace both batteries with new ones.
• Point the remote control at the monitor’s remote
control sensor when...

38
Specifications: PD4201
Screen Size36.3 inches(H)
20.3 inches(V)
921.6 mm(H)
515.3 mm(V)
diagonal 42 inches
Aspect Ratio16 : 9
Resolution1024 pixels(H)
768 pixels(V)
Pixel Pitch0.036 inches(H)
0.027 inches(V)
0.9 mm(H)
0.671 mm(V)
Signals
Synchronization RangeHorizontal : 15.5 kHz to 110.0 kHz
(automatic : step scan)
Vertical : 50.0 Hz to 120.0 Hz
(automatic : step scan)
Input SignalsRGB, NTSC (3.58/4.43), PAL (B,G,M,N),
PAL60, SECAM, HD*1 , DVD*1
Input Terminals
PC/RGB
Visual 1 (Analog)mini D-sub...

39
Table of Signals Supported
Supported resolution: PD4201
•When the screen mode is NORMAL, each signal is converted to a 768 dots
768 lines signal. (Except for *3)
•When the screen mode is ANAMORPHIC, each signal is converted to a 1024 dots
768 lines signal.
Computer input signals supported by this system
Screen modeDots 
 lines
640
400
720
400
640
480
720
400
848
480
852
480*
1
800
600
1024
768
1152
864
1280
768
1280
800*
7
1280
854
1280
960
1360
765
1360
768
1376
768
1280
1024
1400
1050*
7...

40
*1 Only when using a graphic accelerator board that is capable of displayin\
g 852
480.
*2 The picture is displayed in the original resolution. The picture will be compressed for other signals.
*3 Aspect ratio is 5:4. This signal is converted to a 720 dots 
768 lines signal.
*4 Normally the RGB select mode suite for the input signals is set automati\
cally. If the picture is not displayed properly, set
the RGB mode prepared for the input signals listed in the table above.
*5 To connect the monitor to...

09/2006      00M25AV851250    mzh-g
Printed in Japan
www.marantz.com
You can find your nearest authorized distributor or dealer on our website.
is a registered trademark.
1%@$PWFS@/&806.9.7, 4:41 PM Page 2EPCF
1BHF.BLFS
+11$