Marantz Pd4201 User Guide
Here you can view all the pages of manual Marantz Pd4201 User Guide. The Marantz manuals for Television are available online for free. You can easily download all the documents as PDF.
Page 31
32 Reducing image retention The brightness of the screen, the position of the picture, positive/negative mode and screen wiper are adjusted to reduce image retention. Set “ADVANCED OSM” to “ON” in the FUNCTION menu. On “PDP SAVER” of “FUNCTION” menu, select “MANUAL”, then press the MENU/ENTER button. The “PDP SAVER” screen appears. Set “ADVANCED OSM” to “ON” in the FUNCTION menu. On “PICTURE FREEZE” of “FUNCTION” menu, select “BTM LEFT”. SEL. ADJ. RETURNEXIT FUNCTION ADVANCED OSM POWER MGT. INPUT SKIP...
Page 32
33 INVERSE/WHITE Use this to set the inverse mode or to display a white screen. Example: Setting “INVERSE/WHITE” to “WHITE” On “INVERSE/WHITE” of “PDP SAVER” menu, select “WHITE”. SEL. ADJ. RETURNEXIT PDP SAVER PEAK BRIGHT ORBITER INVERSE/WHITE SCREEN WIPER SOFT FOCUS OSM ORBITER OSM CONTRAST: 100% : AUTO1 : WHITE : OFF : OFF : ON : LOW Information INVERSE/WHITE Settings OFF: Inverse/white mode does not function. INVERSE: The picture is displayed alternately between positive image and...
Page 33
34 Reducing the brightness of Closed Caption Use this to reduce the brightness of Closed Caption. Example: Setting “NORMAL” Set “ADVANCED OSM” to “ON” in the FUNCTION menu. On “CAPTION CONT” of “FUNCTION” menu, select “NORMAL”. SEL. ADJ. RETURNEXIT FUNCTION ADVANCED OSM POWER MGT. INPUT SKIP SUB. PICTURE ZOOM NAV PICTURE FREEZE PDP SAVER CLOSED CAPTION CAPTION CONT PWR. ON MODE: OFF : OFF : OFF : BTM LEFT : S BY S1 : MANUAL : OFF : NORMAL Information CAPTION CONT settings NORMAL:...
Page 34
35 Application These specifications cover the communications control of the plasma monitor by external equipment. Connections Connections are made as described below. Connector on the plasma monitor side: EXTERNAL CONTROL connector. Use a crossed (reverse) cable. Type of connector: D-Sub 9-pin male 15 9 62 34 78 Communication Parameters (1) Communication system Asynchronous (2) Interface RS-232C (3) Baud rate 9600 bps (4) Data length 8 bits (5) Parity Odd (6) Stop bit 1 bit (7) Communication code Hex...
Page 35
36 Following is the connection example of STB (Set-top Box) using the REMOTE IN/OUT connectors of the plasma monitor. Consult your dealer about the actual connection and operation. * Connection Example • STB has the REMOTE IN connector. • The pin assignment of the REMOTE IN connector of STB is same as that of 1/8 stereo mini cable connected to the REMOTE OUT connector (Page 35). • The transmit frequency of the remote control of STB is 37.9 kHz (Typical). * The 1/8 Stereo Mini cable must be purchased...
Page 36
37 Remedy • If there are no abnormalities in the image and sound, the noise is caused by the cabinet reacting to changes in temperature. This will not affect performance. • Leave some space between the display and the connected components. • Replace both batteries with new ones. • Plug the monitor’s power cord into a power outlet. • Press the power button on the monitor to turn on the power. • Replace both batteries with new ones. • Point the remote control at the monitor’s remote control sensor when...
Page 37
38 Specifications: PD4201 Screen Size36.3 inches(H)20.3 inches(V) 921.6 mm(H)515.3 mm(V) diagonal 42 inches Aspect Ratio16 : 9 Resolution1024 pixels(H)768 pixels(V) Pixel Pitch0.036 inches(H)0.027 inches(V) 0.9 mm(H)0.671 mm(V) Signals Synchronization RangeHorizontal : 15.5 kHz to 110.0 kHz (automatic : step scan) Vertical : 50.0 Hz to 120.0 Hz (automatic : step scan) Input SignalsRGB, NTSC (3.58/4.43), PAL (B,G,M,N), PAL60, SECAM, HD*1 , DVD*1 Input Terminals PC/RGB Visual 1 (Analog)mini D-sub...
Page 38
39 Table of Signals Supported Supported resolution: PD4201 •When the screen mode is NORMAL, each signal is converted to a 768 dots768 lines signal. (Except for *3) •When the screen mode is ANAMORPHIC, each signal is converted to a 1024 dots768 lines signal. Computer input signals supported by this system Screen modeDots lines 640400 720400 640480 720400 848480 852480* 1 800600 1024768 1152864 1280768 1280800* 7 1280854 1280960 1360765 1360768 1376768 12801024 14001050* 7...
Page 39
40 *1 Only when using a graphic accelerator board that is capable of displayin\ g 852480. *2 The picture is displayed in the original resolution. The picture will be compressed for other signals. *3 Aspect ratio is 5:4. This signal is converted to a 720 dots 768 lines signal. *4 Normally the RGB select mode suite for the input signals is set automati\ cally. If the picture is not displayed properly, set the RGB mode prepared for the input signals listed in the table above. *5 To connect the monitor to...
Page 40
09/2006 00M25AV851250 mzh-g Printed in Japan www.marantz.com You can find your nearest authorized distributor or dealer on our website. is a registered trademark. 1%@$PWFS@/&806.9.7, 4:41 PM Page 2EPCF1BHF.BLFS+11$