Marantz Pd4201 User Guide

10
MENU INPUT/ EXITVOLUMEON/STANDBY
MENUINPUT / EXITVOLUMEON/STANDBY
4567132
qPower
Turns the monitor’s power on and off.
wRemote sensor window
Receives the signals from the remote control.
eON/STANDBY indicator
When the power is on ............................. Lights green.
When the power is in the standby mode ... Lights red.
rINPUT / EXIT
Switches the input.
Functions as the EXIT buttons in the On-Screen Menu
(OSM) mode.
Front View
t
 and 
Enlarges or reduces the image. Functions as the
CURSOR (

 /...

11
AAC IN
Connect the included power cord here.
BEXT SPEAKER L and R
Connect speakers (optional) here. Maintain the correct
polarity. Connect the 
 (positive) speaker wire to the
 EXT SPEAKER terminal and the  (negative)
speaker wire to the 
 EXT SPEAKER terminal on
both LEFT and RIGHT channels.
Please refer to your speaker’s owner’s manual.
CVIDEO1, 2 (RCA, S-Video)
Connect VCR’s, DVD’s or Video Cameras, etc. here.
DAUDIO1, AUDIO2, AUDIO3
These are audio input terminals.
The input is selectable. Set...

14
qPOWER ON/STANDBY
Switches the power on/standby.
(This does not operate when the ON/STANDBY
indicator of the plasma is off.)
wOFF TIMER
Activates the off timer for the unit.
eDISPLAY
Displays the source settings on the screen.
rWIDE
Automatically detects the signal and sets the aspect
ratio.
WIDE button is not active for all signals.
tMENU/ENTER
Press this button to access the OSM controls.
Press this button during the display of the main menu
to go to the sub menu.
yCURSOR ( / 
 / 

 / )
Use these...

15
Basic Operations
POWER
To turn the unit ON and OFF:
1. Plug the power cord into an active AC power outlet.
2. Press the Power button (on the unit).
The monitor’s ON/STANDBY indicator turns red and the
standby mode is set.
3. Press the POWER ON button (on the remote control) to
turn on the unit.
The monitor’s ON/STANDBY indicator will light up
(green) when the unit is on.
4. Press the POWER STANDBY button (on the remote
control) or the Power button (on the unit) to turn off the
unit.
The monitor’s...

16
Wide Screen Operation (manual)
With this function, you can select one of seven screen sizes.
When viewing videos or digital video discs
1. Press the WIDE button on the remote control.
2.Within 3 seconds ...
Press the WIDE button again.
The screen size switches as follows:
→ NORMAL → ANAMORPHIC → STADIUM → ZOOM → 2.35:1 → 14:9 → UNDERSCAN
When a 720P or 1080I signal is input:
ANAMORPHIC ↔  2.35:1
When displaying enhanced split screen:
NORMAL ↔  ANAMORPHIC
NORMAL size screen (4:3)
The normal size screen...

17
Information
 Supported resolution
See page 39, 42 and 45 for details on the display output
of the various VESA signal standards supported by the
monitor.
 When 852 (848) dot  480 line wide VGA*
signals with a vertical frequency of 60 Hz and
horizontal frequency of 31.7 (31.0) kHz are in-
put
Select an appropriate setting for RGB SELECT mode
referring to the“Table of Signals Supported” on page
39, 42 and 45.
*“VGA”, “SVGA” and “SXGA” are registered
trademarks of IBM, Inc. of the United States....

18
Information
Split screen operations may not function depending on
the combination of input signals. In the table below,
“” means Yes, “” means No.
 Split screen operations may not function
depending on the frequency of the RGB
signals.
SPLIT SCREEN Operations
Showing a couple of pictures on the
screen at the same time
* There may be some RGB-input signals that may not be
displayed as not all signals are supported.
1. Press the button to select a screen mode from among single
mode, side-by-side, and...

19
Operations in the Picture-in-picture mode
To move the position of the sub screen, press the cursor 

or  button.
To change the size of the sub screen, press the 
 button.
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
 button
 button
 button
 button
To make the desired picture active, press the ACTIVE
SELECT button.
ACTIVE
SELECT
button
VIDEO1PC/RGB
AB
VIDEO1PC/RGB
AB
A
B
VIDEO1PC/RGBVIDEO1A
B
PC/RGB
Bottom Left Bottom Right

button
button
 button
 button
Top Right

button...

20
Menu Operations
The following describes how to use the menus and the
selected items.
1. Press the MENU/ENTER button on the remote control to
display the MAIN MENU.
MAIN MENU
PICTURE
AUDIO
IMAGE ADJ.SET UP
FUNCTION
SIGNAL INFO.
SEL.EXITMENU/ENTEROKEXIT
2. Press the cursor buttons 
  on the remote control to
highlight the menu you wish to enter.
3. Press the MENU/ENTER button on the remote control to
select a sub menu or item.
SEL. ADJ. RETURN
PICTURE
PICTURE MEMORY
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR...

21
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
PICTURE PICTURE MEMORY OFF/MEMORY1-6 YES 23
CONTRAST←→  0←52→72 YES 23
BRIGHTNESS←→  0←32→64 YES 23
SHARPNESS←→  0←16→32 YES 23
COLOR←→  0←32→64 YES 23
TINT R←→G     0←32→64 YES 23
NR OFF/NR-1/NR-2/NR-3 YES 23
COLOR TEMP. LOW/MIDDLE LOW/MIDDLE/HIGH YES 24
WHITE BALANCE GAIN RED←→  0←40→70 YES 24
GAIN GREEN←→  0←40→70 YES 24
GAIN BLUE←→  0←40→70 YES 24
BIAS RED←→  0←40→70 YES 24
BIAS GREEN←→  0←40→70 YES 24
BIAS...