Makita Lawn Mower PTM0902 Instructions Manual

15ENCONTROLS AND INSTRUMENTS
4.8 CUTTING HEIGHT ADJUSTMENT LEVER
There are seven positions for this lever (shown as «1» to «7» on the label), which corre-
spond to various heights between 3 and 8 cm.
– To go from one height to another, press the release button at the end of the lever.
4.21 CLUTCH / BRAKE PEDAL
This pedal has two functions: during the first part of its travel it acts as a clutch,
engaging and disengaging drive to the wheels, and in the second part it acts as a
brake on the rear wheels
Do...

16ENCONTROLS AND INSTRUMENTS
4.31 BRAKE PEDAL
This pedal works the brake on the rear wheels.
4.32 DRIVE PEDAL
This pedal engages drive in the wheels and controls the machines forward and
reverse speeds.
– To engage forward drive, press it towards «F» with your toe-cap. As you increase
the pressure on the pedal, the speed of the machine increases.
– Reverse is engaged by pressing the pedal with the heel towards «R».
– The pedal automatically goes into neutral «N» when released.
Only shift into reverse...

HOW TO USE THE MACHINE17EN
5.1 SAFETY RECOMMENDATIONS
The machine must only be used for the purpose for which it
was designed (cutting grass). 
Do not tamper with or remove the safety devices fitted on the machine.
REMEMBER THAT THE USER IS ALWAYS RESPONSIBLE FOR DAMAGE AND
INJURY TO OTHERS. Before using the machine:
– read the general safety regulations ( ☛ 1.2), paying particular attention to
driving and cutting on slopes;
– carefully read the instructions for use, make sure you are familiar with the...

18ENHOW TO USE THE MACHINE
– the blades are not engaged;
– the operator is seated or the parking brake is engaged.
b)The engine stops when:
– the operator leaves his seat when the blades are engaged;
– the operator leaves his seat when the transmission is not in “neutral”;
– the operator leaves his seat with the transmission in “neutral” but without applying
the parking brake;
– the parking brake is engaged without disengaging the blades.
5.3 DIRECTIONS BEFORE STARTING WORK
Before starting to mow, it is...

19ENHOW TO USE THE MACHINE
5.3.3 Filling with oil and fuel
The engine manual indi-
cates what type of oil and fuel you can use.
With the engine off, check the oil level.
According to the instructions in the engine
manual, this must be between the MIN and
MAX marks on the dipstick.
Refuel using a funnel, but do not
completely fill the tank.
The tanks capacity is about 6 liters
(Type I) or 4.5 liters (Type II). 
Refuelling
should be carried out in an open or
well-ventilated area with the
engine off. Always...

20ENHOW TO USE THE MACHINE
5.3.4 Checking the protection at the exit (stone-guard)
Never use the
machine without the exit protection in
place!
Always check that the inner spring of the
stone-guard (1) works properly, whilst keep-
ing it securely lowered.
5.3.5 Checking machine safety and efficiency
1. Check that the safety devices function as described  (☛5.2).
2. Check that the brake is in perfect working order.
3. Do not start mowing if the blades vibrate or if you are unsure whether they are
sharp...

21ENHOW TO USE THE MACHINE
area! ALWAYS REMEMBER THAT EXHAUST GASES ARE TOXIC!
To start the engine:
– open the fuel stopcock (1)  ( if fitted);
– shift in the gear into neutral («N») (☛4.22 or 4.32);
– disengage the blades (☛4.7);
– apply the parking brake on sloping ground;
– when starting from cold, move the throttle to the
«CHOKE» position shown on the label;
– if the engine is already warm, position the lever
between «SLOW» and «FAST»;
– put in the ignition key and turn to «ON» to make electri-
cal...

22ENHOW TO USE THE MACHINE
Position the throttle between «SLOW» and
«FAST», and the gear lever in 1st gear (☛4.22).
Keep the pedal pressed down and release the parking brake. Slowly release the
pedal to shift from «brake» to «clutch», thus operating the rear wheels (☛4.21).
The pedal has to be released gradually, as a sudden
engagement may cause the vehicle to tip over and the driver to lose control.
Gradually reach the desired speed using the throttle and gear lever. To change gear,
press the clutch...

23ENHOW TO USE THE MACHINE
5.4.4 Reverse
Reverse must be engaged only when the machine has stopped
moving.
Press the pedal until the machine stops and
then go into reverse by shifting the lever sideways and into position «R»  (☛4.22).
Gradually release the pedal to engage the clutch and then begin moving in reverse.
When the machine has stopped moving, start
reversing by pressing the drive pedal in direction «R»  (☛4.32).
5.4.5 Grass cutting
When you have reached the area to be
mowed, make sure that the...

24ENHOW TO USE THE MACHINE
When cutting on sloping ground, reduce your speed to
ensure safe conditions ( ☛ 1.2 - 5.5).
Whatever the conditions, always reduce the speed if you notice a drop in engine speed
– if you travel too fast compared to the amount of grass being cut, you will not be able
to mow the grass well.
Disengage the blades and raise the cutting deck as high as possible whenever you
need to get past an obstacle.
5.4.6 End of mowing
When you have finished mowing, disengage the blades, lower...