Makita 10 Sliding Compound Mitre Saw With Laser and Mitre Saw Stand User Manual

1 
 
  
INSTRUCTION MANUAL
 
MANUEL DINSTRUCTION  
MANUAL DE INSTRUCCIONES  
DOUBLE INSULATION 
DOUBLE ISOLATION 
DOBLE AISLAMIENTO 
IMPORTANT: Read Before Using. 
IMPORTANT:  Lire avant usage. 
IMPORTANTE:  Leer antes de usar. 
Slide Compound Miter Saw
Scie à Onglet Radiale 
Sierra de Inglete Telescópica 
LS1017 
LS1017L 
  
011345  

2 
ENGLISH (Original instructions) 
SPECIFICATIONS Model 
LS1017 /LS1017L 
Blade diameter  255 mm (10) 
Hole diameter  15.88 mm (5/8) 
Max. Cutting capacities (H x W)   
Bevel angle 
Miter angle  45° (left)  0° 
50 mm x 305 mm  91 mm x 305 mm 0° (2 x 12)  (3-5/8 x 12) 
50 mm x 215 mm  91 mm x 215 mm 45° (2 x 8-1/2)  (3-5/8 x 8-1/2) 
-  91 mm x 150 mm 60° (right)    (3-5/8 x 5-7/8) 
No load speed (RPM)  4,200/min. Laser Type (LS1017L only)  Wavelength 650 nm, Maximum output  1mW  (Laser Class II)...

3 
15. 
DISCONNECT TOOLS before servicing; when 
changing accessories such as blades, bits, 
cutters, and the like. 
16.  REDUCE THE RISK OF UNINTENTIONAL 
STARTING. Make sure switch is in off position 
before plugging in. 
17.  USE RECOMMENDED ACCESSORIES. 
Consult the owners manual for recommended 
accessories. The use of  improper accessories 
may cause risk of injury to persons. 
18.  NEVER STAND ON TOOL. Serious injury could 
occur if the tool is tipped or if the cutting tool 
is unintentionally...

4 
8. 
To reduce the risk of injury, return carriage to 
the full rear position after each crosscut 
operation. 
9.  Always secure all moving portions before 
carrying the tool. 
10.  Stopper pin which locks the cutter head down 
is for carrying and storage purposes only and 
not for any cutting operations. 
11 .  
Do not use the tool in the presence of 
flammable liquids or gases. The electrical 
operation of the tool could create an explosion and 
fire when exposed to flammable liquids or gases. 
12....

5 
USB088-3 
ADDITIONAL SAFETY RULES 
FOR THE LASER 
 
CAUTION: • LASER RADIATION  DO NOT STARE INTO 
BEAM. 
• AVOID EXPOSURE - LASER RADIATION IS 
EMITTED FROM APERTURE.  
• USE OF CONTROLS OR ADJUSTMENTS OR 
PERFORMANCE OF PROCEDURES OTHER 
THAN THOSE SPECIFIED HEREIN MAY 
RESULT IN HAZARDOUS RADIATION 
EXPOSURE. 
CAUTION / PRECAUCIÓNLASER RADIATION DO NOT STARE INTO BEAM
Maximum Output 
< 1mW, Wavelength : 650 nm
CLASS     LASER PRODUCTRADIACIÓN LÁSER NO DIRIJA LA 
VISTA HACIA EL RAYO LÁSER
COMPLIES...

6 
If the see-through blade guard becomes dirty, or sawdust 
adheres to it in such a way that the blade and/or workpiece 
is no longer easily visible, unplug the saw and clean the 
guard carefully with a damp cloth. Do not use solvents or 
any petroleum-based cleaners on the plastic guard 
because this may cause damage to the guard. 
If the blade guard becomes dirty and needs to be 
cleaned for proper operation follow the steps below: 
With the tool switched off and unplugged, use the 
supplied socket...

7 
With the tool unplugged, rotate the blade by hand while 
holding the handle all the way down to be sure that the 
blade does not contact any part of the lower base. 
Re-adjust slightly
, if necessary. 
 
WARNING: • After installing a new blade and with the tool 
unplugged, always be sure that the blade does 
not contact any part of the lower base when the 
handle is lowered completely.  If a blade makes 
contact with the base it may cause kickback and 
result in serious personal injury. 
Stopper arm...

8 
12
3
  011353 Tilt the saw blade until the pointer points to the desired 
angle on the bevel scale. Then tighten the lever 
clockwise firmly to secure the arm. 
• When changing bevel angles, be sure to position 
the kerf boards appropriately as explained in the 
Positioning kerf boards section. 
 
CAUTION: • After changing the bevel angle, always secure the 
arm by tightening the lever clockwise. 
NOTICE: 
• When tilting the saw blade be sure the handle is 
fully raised. 
• When changing bevel...

9 
Laser beam action For model LS1017L only  
NOTE: • Before the first use, install the dry cells provided 
separately from the tool in the cell box. Refer to the 
section titled “Replacing the dry cells for laser unit” 
for the installment. 
CAUTION: • When not in use, be sure to turn off the laser 
1  010257 
CAUTION: • LASER RADIATION 
Do not stare into beam. 
• Before shifting the laser line or performing 
maintenance adjustment, be sure to unplug the 
tool. 
To turn on the laser beam, press the...

10 
Storage of socket wrench with hex wrench on 
its other end 
12  011338 The socket wrench is stored as shown in the figure. 
When the socket wrench is needed it can be pulled out of 
the wrench holder. After using the socket wrench it can 
be stored by returning it to the wrench holder. 
Installing or removing saw blade  
WARNING: • Always be sure that the tool is switched off and 
unplugged before installing or removing the 
blade.
 Accidental start up of the tool may result in 
serious personal...