Lucent Technologies Remote Port Security Device Users Guide

Installation 
Page 2-1  
2
Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
2
2Installation
This chapter describes the recommended room layout and environment, 
hardware components, installation procedures, and testing for the RPSD. See 
Appendix A: “Cables, Connectors, and Ports” for quick reference materials on 
the installation of the hardware components. 

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
Installation 
Page 2-2 Room Layout/Environment 
2
Room Layout/Environment
While the location of the RPSD Lock is not critical to its function, the Lock should 
be kept in an equipment cabinet near the communications system modem. This 
helps to protect the Lock against dust and other precipitate, as well as protecting 
it against physical damage from being knocked to the floor or having things 
dropped on it. You also can place...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
Installation 
Page 2-3 Room Layout/Environment 
2
Location of Administration Terminal or Printer
For installation purposes, it is simplest if the RPSD Lock or Key administration 
terminal or printer is in the same area as the Lock or Key. If the terminal or printer 
must be located at some distance from the Lock or Key (in another room, on 
another floor, etc.), the limitations of the EIA-RS232 interface must be 
considered.
To...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
Installation 
Page 2-4 Installation 
2
Installation
Prior to installing the RPSD system, make sure you have all the hardware 
components. Also, consider these two items before you start the installation:
nYou must inform the INADS System Administrator at the local or central 
Technical Support Center (TSC) when the installation will take place and 
that the RMATS port will be down at that time. This ensures that no one 
tries to...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
Installation 
Page 2-5 Installation 
2
Cables, Connectors, and Ports
Ta b l e  2 - 1 shows the cables, connectors, and ports required to install the RPSD 
system. This table includes optional connections as well as the basic 
configuration.
Installing the RPSD Lock
Install the RPSD Lock between the central office line that is reserved as the 
remote maintenance and administration channel and the communications 
system modem (see...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
Installation 
Page 2-6 Installation 
2
The modem location depends on the type of communications system. The 
modem is located:
non the circuit pack for System 75 and DEFINITY Generic 1.
nexternal to the communications system for System 85 and DEFINITY 
Generic 2.
Figure 2-1. Common RPSD Lock Configuration
Connect the RPSD Lock to the administration terminal via the AUX. PORT on the 
back of the Lock, and power it from an AC...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
Installation 
Page 2-7 Installation 
2
You  need the following components to install the RPSD Lock:
nRPSD Lock
nThe central office line assigned as the RMATS channel (on customer 
premises)
nThe communications system modem (on customer premises)
n7-foot line cord with RJ11 modular connectors
n14-foot line cord with RJ11 modular connectors
nDB9 (male) to DB25 (female) cable
nRS-232 cable
nAdministration terminal for the Lock
nRPSD...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
Installation 
Page 2-8 Installation 
2
Figure 2-2. RPSD Lock to Central Office Line (RMATS Channel)
To connect the RPSD Lock to the central office line, follow these steps:
1. The customer must contact the Technical Support Center to get the port 
number for the RMATS channel.
2. Locate the central office line for the RMATS port and install an RJ11 
receptacle on the central office line.
3. Connect one end of the 14-foot...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
Installation 
Page 2-9 Installation 
2
Connecting the RPSD Lock to the 
Communications System Modem
You connect the communications system modem to the RPSD Lock by using the 
7-foot line cord supplied with the Lock.  Obtain further information for the modem 
from the documentation accompanying that modem.
The following components are needed to connect the RPSD Lock to the 
communications system modem:
nRPSD Lock
nCommunications...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
Installation 
Page 2-10 Installation 
2
Figure 2-3. RPSD Lock to Modem
SUBSCRIBER
(MODEM) TELCO
AUX. PORT
+!
12VDC
1A
ALARM
LEADS
POWER MONITOR
RED
GREEN BYPASSSECURE
Communications
System Modem
RJ11
Connector RJ11
Connector