LG Flatron M2362dp Owners Manual

							31
EXTERNAL  EQUIPMENT  SETUP
Connecting with an HDMI to DVI cable
Connect the DVI output of the PC to the HDMI/DVI IN jack on the SET.
Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the SET.
Turn on the PC and the SET.
Select HDMI  input source using the INPUT  button on the remote control.
1
2
3
4
1
2
 ►Connect the signal input cable and tighten it up by turning in 
the direction of the arrow as shown in the figure.
NOTE!
 ►If you want to use HDMI-PC mode, you must set the input label to PC mode.
   
						

							32
EXTERNAL EQUIPMENT SETUP
EXTERNAL  EQUIPMENT  SETUP
Connecting with an HDMI to HDMI cable
Connect the HDMI output of the PC to the HDMI/DVI IN 
jack on the SET.
Turn on the PC and the SET.
Select HDMI input source using the INPUT  button on the 
remote control.
1
2
3
NOTE
 ►Check  that  your  HDMI  cable  is  High  Speed  HDMI  Cable.  If  the  HDMI  cables  are  not  High  Speed HDMI 
Cable, flickering or no screen display can result. Please use the High Speed HDMI Cable.
 ►If you want to use HDMI-PC mode, you must set the input label to PC mode.
!
1
 
						

							33
EXTERNAL  EQUIPMENT  SETUP
BACK COVER FOR WIRE ARRANGEMENT
Tie cables together with a cable management as shown in the illustration.
   
						

							34
EXTERNAL EQUIPMENT SETUP
EXTERNAL  EQUIPMENT  SETUP
SUPPORTED DISPALY RESOLUTION
RGB[PC] / HDMI[PC] mode
ResolutionHorizontal
Frequency(kHz)
Vertical
Frequency(Hz)
640 x 48031.46959.94
640 x 48037.575
800 x 60037.87960.317
800 x 60046.87575.0
1024 x 76848.36360.0
1280 x 76847.77659.87
1360 x 76847.71260.015
ResolutionHorizontal
Frequency(kHz)
Vertical
Frequency(Hz)
640 x 48031.46959.94
640 x 48037.575
800 x 60037.87960.317
800 x 60046.87575
832 x 62449.72564.55
1024 x 76848.36360
1024 x 76860.02375.029
1280 x 102463.98160.02
1280 x 102479.97675.025
1600 x 9006060
ResolutionHorizontal
Frequency(kHz)
Vertical
Frequency(Hz)
720 x 40031.46870.08
640 x 48031.46959.94
640 x 48037.575
800 x 60037.87960.317
800 x 60046.87575.0
1024 x 76848.36360.0
1024 x 76860.02375.029
1152 x 86467.50075.000
1280 x 102463.98160.02
1280 x 102479.97675.025
1680 x 105064.67459.883
1680 x 105065.29059.954
1600 x 120075.060.0
1920 x 108067.560
M1962DP
M2062DP
Only HDMI[PC] Mode
M2262DP/M2362DP/M2762DP
 
						

							35
EXTERNAL  EQUIPMENT  SETUP
HDMI - DTV modeComponent mode
ResolutionHorizontal
Frequency(kHz)
Vertical
Frequency(Hz)
720 x 48031.469
31.5
59.94
60
720 x 57631.2550
1280 x 72037.50050
1280 x 72044.96
45
59.94
60
1920 x 108033.72
33.75
59.94
60
1920 x 108028.12550.00
1920 x 10802724
1920 x 108033.7530.00
1920 x 108056.25050
1920 x 108067.43
67.5
59.94
60
ResolutionHorizontal
Frequency(kHz)
Vertical
Frequency(Hz)
720 x 48015.7359.94
720 x 48015.7560.00
720 x 57615.62550.00
720 x 48031.4759.94
720 x 48031.5060.00
720 x 57631.2550.00
1280 x 72044.9659.94
1280 x 72045.0060.00
1280 x 72037.5050.00
1920 x 108033.7259.94
1920 x 108033.7560.00
1920 x 108028.12550.00
1920 x 108056.2550
1920 x 108067.43259.94
1920 x 108067.560.00
NOTE
 ►Avoid keeping a fixed image on the set’s screen 
for  prolonged  periods  of  time.  The  fixed  image 
may  become  permanently  imprinted  on  the 
screen use a screen saver when possible.
 ►There  may  be  interference  relating  to  resolution, 
vertical  pattern,  contrast  or  brightness  in  PC 
mode. Change the PC mode to another resolution 
or change the refresh rate to another rate or adjust 
the  brightness  and  contrast  on  the  menu  until  the 
picture is clear. If the refresh rate of the PC graph-
ic  card  can  not  be  changed,  change  the  PC 
graphic card or consult the manufacturer of the PC 
graphic card. 
 ►The synchronization input waveform for Horizontal 
and Vertical frequencies are separate.
 ►Connect  the  signal  cable  from  the  monitor  output 
port of the PC to the RGB (PC) port of the SET or 
the  signal  cable  from  the  HDMI  output  port  of  the 
PC to the HDMI/DVI IN port on the SET.
 ►Connect the audio cable from the PC to the Audio 
input  on  the  SET.  (Audio  cables  are  not  included 
with the SET).
 ►If  using  a  sound  card,  adjust  PC  sound  as 
required.
 ►If the graphic card on the PC does not output ana-
logue  and  digital  RGB  simultaneously,  connect 
only one of either RGB or HDMI/DVI IN to display 
the PC output on the SET.
 ►If  the  graphic  card  on  the  PC  does  output  ana-
logue and digital RGB simultaneously, set the SET 
to either RGB or HDMI. (The other mode is set to 
Plug and Play automatically by the SET.)
 ►DOS mode may not work depending on the video 
card if you use an HDMI to DVI cable. 
 ►If  you  use  too  long  an  RGB-PC  cable  that  is  too 
long, there may be interference on the screen. We 
recommend  using  under  5m  of  cable.  This  pro-
vides the best picture quality.
!
   
						

							36
WATCHING TV / PROGRAMME CONTROL
WATCHING  TV  /  PROGRAMME  CONTROL
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the set.
ꔰ(POWER)
ENERGY SAVING
TV/PC 
INPUT
TV/RAD
Switches the set on from standby or off to standby.
 
Adjust the Energy Saving mode of the SET.
(► P. 68)
Selects TV or PC mode.
External input mode rotates in regular sequence. 
Selects Radio, TV and DTV channel.
0~9  number
button
LIST
Q.VIEW
MENU
GUIDE
Q. MENU
THUMBSTICK
(Up/Down/Left/Right)
OK
BACK
꘍
EXIT
Selects a programme.
Selects numbered items in a menu.
Displays the programme table. (► P. 58)
Returns to the previously viewed programme.
Selects a menu.
Clears  all  on-screen  displays  and  returns  to  TV viewing from any menu. (► P. 40)
Shows programme schedule. (► P. 61 to 64)
Select  the  desired  quick  menu  source.  (Aspect Ratio,  Clear  Voice  II  ,  Picture  Mode,  Sound  Mode, Audio, Sleep Timer, Favourite, USB Device). (►P.39)
Allows  you  to  navigate  the  on-screen  menus  and adjust the system settings to your preference.
Accepts your selection or displays the current mode.
Allows the user to move return one step in an inter-active  application,  EPG  or  other  user  interaction function.
Shows the present screen information.
Clears  all  on-screen  displays  and  returns  to  TV viewing from any menu
Coloured
buttons
These buttons are used for teletext (on TELETEXT
models only) , Programme edit.
 
						

							37
WATCHING  TV  /  PROGRAMME  CONTROL
VOLUME UP/DOWN
FAV
MARK
RATIO
MUTE
Programme
UP/DOWN
PAGE
UP/DOWN
TELETEXT
BUTTONS
SUBTITLE
USB Menu
control
buttons
Auto Config.
Adjusts the volume.
Displays the selected favourite programme. 
(► P. 59)
Check and un-check programmes in the USB menu.
Selects your desired Aspect Ratio of picture.
Switches the sound on or off.
Selects a programme.
Move  from  one  full  set  of  screen  information  to  the 
next one.
These buttons are used for teletext.
For further details, see the ‘Teletext’ section. 
(► P. 130 to 131)
Recalls your preferred subtitle in digital mode.
USB menu(Photo List and Music List or Movie List ).
Automatically  adjusts  picture  position  and  mini-
mizes image instability.
1
1
Installing Batteries
 ■Open  the  battery  compartment  cover  on  the  back  side  and 
install the batteries matching correct polarity (+with +, -with -)
 ■Install two 1.5 V AAA batteries. Don’t mix old or used batteries 
with new ones.
 ■Close cover.
 ■To  remove  the  batteries,  perform  the  installation  actions  in 
reverse.
   
						

							38
WATCHING TV / PROGRAMME CONTROL
WATCHING  TV  /  PROGRAMME  CONTROL
TURNING ON THE TV
 -When your TV is turned on, you will be able to use its features.
PROGRAMME SELECTION
VOLUME ADJUSTMENT
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
In  standby  mode  to  turn  TV  on,  press  the   /  I,  INPUT  or Pꕌꕍ  button  on  the  TV  or  press  the 
POWER, INPUT, Pꕌꕍor NUMBER button on the remote control and the TV will switch on.
Initializing setup
If  the  OSD  (On  Screen  Display)  is  displayed  on  the  screen  after  turning  on  the  TV,  you  can  adjust  the 
Language,  Mode  Setting,  Country  or Set  Password  (When  France  is  selected  for  Country), Auto 
Tuning.
Note:
a. If you close without completing the initial setting, the Initial Setting menu can be displayed again.
b. Press the BACK button to change the current OSD to the previous OSD.
c.  For  those  countries  without  confirmed  DTV  broadcasting  standards,  some  DTV  features  might  not  work, 
depending on the DTV broadcasting environment.
d. "Home Use” mode is the optimal setting for home environments, and is the TV's default mode.
e. "Store Demo" mode is the optimal setting for store environments. If a user modifies image quality data, “Store 
Demo” mode initializes the product to the image quality set by us after a certain period of time.
f. The mode (Home Use, Store Demo) can be changed by executing Mode Setting in the OPTION menu.
g. When France is selected for Country, password is not ‘0’, ‘0’, ‘0’, ‘0’ but ‘1’, ‘2’, ‘3’, ‘4’.
Press the P ꕌ ꕍ or NUMBER buttons to select a programme number.
Press the  + or - button to adjust the volume.
If you wish to switch the sound off, press the MUTE button.
You can cancel this function by pressing the MUTE,  + , - button.
1
2
1
1
2
 
						

							39
WATCHING  TV  /  PROGRAMME  CONTROL
QUICK MENU
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
ꔣ Aspect  Ratio:  Selects  your  desired  picture  for-
mat.For  Zoom  Setting,  select  14:9,  Zoom  and 
Cinema  Zoom  in  Ratio  Menu.  After  completing 
Zoom Setting, the display goes back to Q.Menu. 
ꕅ Clear Voice II: By differentiating the human sound 
range from others, it helps users listen to human 
voices better.
ꕇ Picture  Mode:  Selects  your  desired  Picture 
Mode.
ꕈ Sound  Mode:  It  is  a  feature  to  automatically  set 
the  sound  combination  which  it  deems  the  best 
for  the  images  being  watched.  Selects  your 
desired Sound Mode.
ꔴ Audio: Selects the sound output. 
ꔤ Sleep Timer: Sets the sleep timer.
ꔲ Favourite: Selects the favourite programme.
ꔢ USB  Device:  Selects  “Eject”  in  order  to  eject 
USB  device.
 ◄        Aspect Ratio           ►
1
2
3
Display each menu.
Select your desired Source.
• Press the BACK button to move to the previous menu screen.
16:9
   
						

							40
WATCHING TV / PROGRAMME CONTROL
WATCHING  TV  /  PROGRAMME  CONTROL
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your set's OSD (On Screen Display) may differ slightly from what is shown in this manual.
SETUP
SETUPMoveMoveMoveOKOKOK
OPTION
PICTURE
PICTURE
LOCK
AUDIO
AUDIO
TIME
USBINPUTLOCK
OPTION
INPUT
TIME
USB
MoveOK
MoveMoveMove
Move
OKOKOK
OK
Auto Tuning
Manual Tuning
Programme Edit
Software Update    : ON
Diagnostics
CI Information
Menu Language  : English
Audio Language   : English
Subtitle Language    : English
Disabled Assistance
Country     :  
- -
Input Label
Set ID   : 1
Power Indicator   : On
▼
Set Password
Lock System   : Off
 • Block Programme
  • Parental Guidance
 • Input Block 
Key Lock  : Off
Antenna
AV
Component
RGB
HDMI
Photo List
Music List
Movie List
DivX Reg. Code
Deactivation
Aspect Ratio   : 16:9
Picture Wizard
ꕊ Energy Saving   : Off
Picture Mode   : Vivid
  • Backlight    100
  • Contrast  100
  • Brightness  50
  • Sharpness  70
▼
Auto Volume   : Off
Clear Voice II   : Off ꕅ3
Balance      0
Sound Mode  : Music
  • Surround X  
        : Off
  • Treble  50
  • Bass   50
  • Reset
▼
Clock
Off Time   : Off
On Time   : Off
Sleep Timer   : Off
1
2
3
MENU
Select a menu item.
Display each menu.
Move to the pop up menu.
• Press the MENU or EXIT button to close the menu window.
• Press the BACK  button to move to the previous menu screen.
NOTE
 ►It is not possible to use CI Information in Analogue mode.
!