LG Flatron M2362dp Owners Manual

							141
APPENDIX

LCD Panel
S c r e e n   Ty p e
584.2 mm Wide (23 inch) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size : 584.2 mm
P i x e l   P i t c h0.265 mm (H) x 0.265 mm (V)
Video Signal
Max.  Resolution1920 x 1080 @ 60 Hz
Recommended Resolution1920 x 1080 @ 60 Hz 
Horizontal  Frequency30 kHz to 83 kHz
Vertical  Frequency56 Hz to 75 Hz
Synchronization TypeSeparate Sync, Digital
Input ConnectorTV, D-Sub Analog, SCART, PC Audio In, component, HDMI
Power
R a t e d   Vo l t a g eAC 100-240 V~ 50 / 60 Hz 1.2 A
Power ConsumptionOn Mode : 55 W (typ.)
Off Mode  ≤ 0.5  W
TiltTi l t   R a n g e-5° to 15°
Dimensions (Width x Height x Depth)
Weight
551.8 mm x 419.5 mm x 221.6 mm (21.72 inch x 16.32 inch x 8.72 inch)
5.18 kg ( 11.4 lb)
Environmental
conditions
Operating Temperature
Operating Humidity
10 °C to 35 °C
20 % to 80 %
-10 °C to 60 °C
   5 % to 90 %
Storage Temperature
Storage Humidity
 ■The specifications shown above may be changed without prior notice for quality improvement.
 
						

							142
APPENDIX
APPENDIX
 ■The specifications shown above may be changed without prior notice for quality improvement.

LCD Panel
S c r e e n   Ty p e
686 mm Wide (27 inch) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size: 686 mm
P i x e l   P i t c h0.3114 mm (H) x 3114 mm (V)
Video Signal
Max.  Resolution1920 x 1080 @ 60 Hz
Recommended Resolution1920 x 1080 @ 60 Hz 
Horizontal  Frequency30 kHz to 83 kHz
Vertical  Frequency56 Hz to 75 Hz
Synchronization TypeSeparate Sync, Digital
Input ConnectorTV, D-Sub Analog, SCART, PC Audio In, component, HDMI
Power
R a t e d   Vo l t a g eAC 100-240 V~ 50 / 60 Hz 1.2 A
Power ConsumptionOn Mode : 63 W (typ.)
Off Mode  ≤ 0.5  W
TiltTi l t   R a n g e-5° to 15°
Dimensions (Width x Height x Depth)
Weight
649.1 mm x 485 mm x 210 mm (25.56 inch x 19.09 inch x 8.27 inch)
7.2 kg ( 15.87lb)
Environmental
conditions
Operating Temperature
Operating Humidity
10 °C to 35 °C
20 % to 80 %
-10 °C to 60 °C
   5 % to 90 %
Storage Temperature
Storage Humidity
 
						

							143
APPENDIX
IR CODES
• This feature is not available for all models.
Code (Hexa)   FunctionNote
95Energy Saving  R/C BUTTON 
08POWER   R/C BUTTON (POWER ON/OFF)
50TV / PC  R/C BUTTON
0BINPUT  R/C BUTTON
79RATIO  R/C BUTTON
F0TV/RAD  R/C BUTTON
45Q.MENU  R/C BUTTON
43MENU  R/C BUTTON
ABGUIDE  R/C BUTTON
40Up (ꕌ)  R/C BUTTON
41Down (ꕍ)  R/C BUTTON
07Left ()  R/C BUTTON
44OK(ꔉ)  R/C BUTTON
28BACK  R/C BUTTON
5BEXIT  R/C BUTTON
AA꘍  R/C BUTTON
02 ( + )  R/C BUTTON
03 ( - )  R/C BUTTON
1EFAV ( MARK )  R/C BUTTON
09MUTE  R/C BUTTON
00P (ꕌ)  R/C BUTTON
01P (ꕍ)    R/C BUTTON
10 to 19Number Key 0 to 9  R/C BUTTON
53LIST  R/C BUTTON
1AQ.VIEW  R/C BUTTON
72RED Key  R/C BUTTON
71GREEN Key  R/C BUTTON
63YELLOW Key  R/C BUTTON
61BLUE Key  R/C BUTTON
20TEXT  R/C BUTTON
21T.OPT (T.Option)  R/C BUTTON
39SUBTITLE  R/C BUTTON
99Auto Config.  R/C BUTTON
B1▀  R/C BUTTON
B0►  R/C BUTTON
BAl l  R/C BUTTON
8F◄◄  R/C BUTTON
8E►►  R/C BUTTON
 
 
						

							144
APPENDIX
APPENDIX
EXTERNAL CONTROL DEVICE SETUP
RS-232C Setup
Connect  the  RS-232C  (serial  port)  input  jack  to  an 
external  control  device  (such  as  a  computer  or  an 
A/V  control  system)  to  control  the  product’s  func-
tions externally.
Connect  the  serial  port  of  the  control  device  to  the 
RS-232C jack on the product back panel.
Note:  RS-232C  connection  cables  are  not  supplied 
with the product.
15
69
RS-232C Configurations
7-Wire Configurations (Standard RS-232C cable)
   PC  TV  
 RXD    2  3 TXD
 TXD  3  2 RXD
 GND  5  5 GND
 DTR  4  6 DSR
 DSR  6  4 DTR
 RTS  7  8 CTS
 CTS  8  7 RTS  
    D-Sub 9  D-Sub 9
3-Wire Configurations(Not standard)
   PC  TV  
 RXD    2  3 TXD
 TXD  3  2 RXD
 GND  5  5 GND
 DTR  4  6 DTR
 DSR  6  4 DSR
 RTS  7  7 RTS
 CTS  8  8 CTS  
    D-Sub 9  D-Sub 9
Type of Connector; D-Sub 9-Pin Male
No. Pin Name
1
2
3
4
5
6
7
8
9
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
 
						

							145
APPENDIX
Set ID
Use this function to specify a set ID number.
Refer to ‘Real Data Mapping’. ► p.150
OPTIONOPTION
Menu Language  : English
Audio Language   : English
Subtitle Language    : English
Disabled Assistance
Country     :  
- -
Input Label
Set ID   : 1
Power Indicator   :On
▼
Menu Language   : English
Audio Language   : English
Subtitle Language    : English
Disabled Assistance
Country     :  
- -
Input Label
Set ID   : 1
Power Indicator   :On
▼
MoveMoveOKOK
Set ID    : 1                   ꔉ  Set ID   : 1                   ꔉ  
➩
◄                1               ►
Close
1
2
3
MENU
Select Set ID.
Adjust Set ID to choose the desired TV ID number.
The adjustment range of SET ID is 1 to 99.
Select OPTION.
• Press the MENU or EXIT button to close the menu window.
• Press the BACK  button to move to the previous menu screen.
 
						

							146
APPENDIX
APPENDIX
Communication Parameters
 ■Baud rate: 9600 bps (UART)
 ■Data length: 8 bits
 ■Parity : None
 ■Stop bit: 1 bit
 ■Communication code: ASCII code
 ■Use a crossed (reverse) cable.
Transmission
*  [Command 1]  :   First command to control the TV.
     (j, k, m or x)
*  [Command 2]   :   Second command to control the TV.
*  [Set ID]   :   You  can  adjust  the  set  ID  to  choose 
desired  monitor  ID  number  in  option 
menu. Adjustment range is 1 to 99. 
      When  selecting  Set  ID  ‘0’,  every  con-
nected set is controlled.
     Set ID is indicated as decimal (1 to  99) on 
menu and as Hexa decimal (0x0 to 0x63) 
on transmission/receiving protocol.
*  [DATA]   :  To transmit command data.
       Transmit ‘FF’ data to read status of com-
mand.
*  [Cr]     :  Carriage Return
     ASCII code ‘0x0D’
*  [   ]     :  ASCII code ‘space (0x20)’
[Command1][Command2][  ][Set ID][  ][Data][Cr]
OK Acknowledgement
*  The  set  transmits  ACK  (acknowledgement)  based 
on  this  format  when  receiving  normal  data.  At  this 
time, if the data is data read mode, it indicates pres-
ent  status  data.  If  the  data  is  data  write  mode,  it 
returns the data of the PC computer.
[Command2][  ][Set ID][  ][OK][Data][x]
Error Acknowledgement
*  The  set  transmits  ACK  (acknowledgement)  based 
on this format when receiving abnormal data from 
  non-viable functions or communication errors.
Data  00: Illegal Code
[Command2][  ][Set ID][  ][NG][Data][x]
Transmission / Receiving Protocol
Command Reference List
* When setting the 17 to 24, a menu does not appear on 
screen.
* Note : During USB operations such as Dvix or EMF, all 
commands except Power(ka) and Key(mc) are not exe-
cuted and treated as NG.
 COMMAND 
1
COMMAND 
2
DATA
(Hexadecimal)
01. Power  ka00  to  01 
02. Aspect Ratio kcRefer to p. 147
03. Screen Mute kd00  to  01
04. Volume Mute ke00  to  01
05. Volume Control kf00  to  64
06. Contrast kg00  to  64
07. Brightness kh00  to  64
08. Colourki00  to  64
09. Tint kj00  to  64
10. Sharpness kk00  to  64 
11. OSD Select kl00  to  01
12. Remote control lock modekm00  to  01
13. Treble  kr00  to  64
14. Bassks00  to  64
15. Balance kt00  to  64
16. Colour Temperaturexu00  to  64
17. Energy Savingjq00  to  05
18. Auto Configurationju01
19. Tune CommandmaRefer to p. 149
20. Programme Add/Skipmb00  to  01
21. KeymcKey Code
22. Back Lightmg00  to  64
23. Input select (Main)x bRefer to p. 150
 
						

							147
APPENDIX
04. Volume Mute (Command: k e)
 ►To control volume mute on/off. You can also adjust mute using the MUTE button on remote control.
Transmission
Data 00 :  Volume mute on (Volume off)  01  :  Volume mute off (Volume on) 
[k][e][  ][Set ID][  ][Data][Cr]
Ack
[e][  ][Set ID][  ][OK/NG][Data][x]
02. Aspect Ratio (Command: k c) (Main Picture Size)
 ►To adjust the screen format. (Main picture format)
  You  can  also  adjust  the  screen  format  using  the 
Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission
Data  01   :  Normal screen (4:3)   02  :  Wide screen (16:9)   04  :  Zoom 06  :  Original
07  :  14:909  :  Just Scan0B  :  Full  Wide10 to 1F :  Cinema Zoom 1 to 16
[k][c][  ][Set ID][  ][Data][Cr]
Ack
*  Using  the  PC  input,  you  select  either  16:9  or  4:3 
screen aspect ratio.
* In  DTV/HDMI  (1080i  50  Hz  /  60  Hz,  720p  50  Hz  / 
60  Hz,  1080p  24  Hz  /  30  Hz  /  50  Hz  /  60  Hz), 
Component(  720p,  1080i,  1080p  50  Hz  /  60  Hz) 
mode, Just Scan is available.
* Full Wide is supported only for Analogue, AV.
[c][  ][Set ID][  ][OK/NG][Data][x]
03. Screen Mute (Command: k d)
 ►To select screen mute on/off.
Transmission
Data  00 :  Screen mute off (Picture on)
      Video mute off
 01 :  Screen mute on (Picture off)
 10 :  Video mute on
*  In  case  of  video  mute  on  only,  TV  will  display  On 
Screen Display(OSD). But, in case of Screen mute 
on, TV will not display OSD.
[k][d][  ][Set ID][  ][Data][Cr]
Ack
[d][  ][Set ID][  ][OK/NG][Data][x]
05. Volume Control (Command: k f)
 ►To adjust volume. You  can  also  adjust  volume  with  the VOLUME  but-tons on remote control.
Transmission
Data  Min : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 150.
[k][f][  ][Set ID][  ][Data][Cr]
Ack
[f][  ][Set ID][  ][OK/NG][Data][x]
06. Contrast (Command: k g)
 ►To adjust screen contrast.  You can also adjust contrast in the PICTURE menu.
Transmission
Data  Min : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 150.
[k][g][  ][Set ID][  ][Data][Cr]
[g][  ][Set ID][  ][OK/NG][Data][x]
01. Power (Command: k a)
 ►To control Power On/Off of the set.
Transmission
Data 00 : Power Off01 : Power On
[k][a][  ][Set ID][  ][Data][Cr]
Ack
[a][  ][Set ID][  ][OK/NG][Data][x]
 ►To show Power On/Off.
Transmission
[k][a][  ][Set ID][  ][FF][Cr]
Ack
*  Similarly,  if  other  functions  transmit  ‘0xFF’  data 
based  on  this  format, Acknowledgement  data  feed 
back presents status about each function.
*  OK  Ack.,  Error  Ack.  and  other  message  may  dis-
play on the screen when TV is power On.
[a][  ][Set ID][  ][OK/NG][Data][x]
Ack
 
						

							148
APPENDIX
APPENDIX
12. Remote control lock mode (Command: k m)
 ►To  lock  the  front  panel  controls  on  the  monitor  and 
remote control.
Transmission
[k][m][  ][Set ID][  ][Data][Cr]
Ack
Data 00 : Lock off01 : Lock on
* If you are not using the remote control, use this mode. When main power is on/off, external control lock is released.* Local Power Key will work properly.
[m][  ][Set ID][  ][OK/NG][Data][x]
11. OSD Select (Command: k l)
 ►To select OSD (On Screen Display) on/off when control-
ling remotely.
Transmission
[k][l][  ][Set ID][  ][Data][Cr]
Ack
 Data 00 : OSD off01 : OSD on
[l][  ][Set ID][  ][OK/NG][Data][x]
09. Tint (Command: k j)
 ►To adjust the screen tint. (Except PC mode)
  You can also adjust tint in the PICTURE menu.
Transmission
Data  Red : 00 to Green : 64 * Refer to ‘Real data mapping 1’. See page 150.
[k][j][  ][Set ID][  ][Data][Cr]
Ack
[j][  ][Set ID][  ][OK/NG][Data][x]
 ►To adjust the screen sharpness. You can also adjust sharpness in the PICTURE menu.
Transmission
10. Sharpness (Command: k k)
Data  Min : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 150.
[k][k][  ][Set ID][  ][Data][Cr]
Ack
[k][  ][Set ID][  ][OK/NG][Data][x]
14. Bass (Command: k s)
 ►To adjust bass.   You can also adjust bass in the AUDIO menu.
Transmission
Data  Min : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 150.
[k][s][  ][Set ID][  ][Data][Cr]
Ack
[s][  ][Set ID][  ][OK/NG][Data][x]
13. Treble (Command: k r)
 ►To adjust treble.  You can also adjust treble in the AUDIO menu.
Transmission
Data  Min : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 150 .
[k][r][  ][Set ID][  ][Data][Cr]
Ack
[r][  ][Set ID][  ][OK/NG][Data][x]
08. Colour (Command: k i)
 ►To adjust the screen colour. (Except PC mode) You can also adjust colour in the PICTURE menu.
Transmission
Data  Min : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 150.
[k][i][  ][Set ID][  ][Data][Cr]
Ack
[i][  ][Set ID][  ][OK/NG][Data][x]
07. Brightness (Command: k h)
 ►To adjust screen brightness. You can also adjust brightness in the PICTURE menu.
Transmission
Data  Min : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 150.
[k][h][  ][Set ID][  ][Data][Cr]
Ack
[h][  ][Set ID][  ][OK/NG][Data][x]
 
						

							149
APPENDIX
15. Balance (Command: k t)
 ►To adjust balance. You can also adjust balance in the AUDIO menu.
Transmission
Data  Min : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 150.
[k][t][  ][Set ID][  ][Data][Cr]
Ack
[t][  ][Set ID][  ][OK/NG][Data][x]
16. Colour Temperature (Command: x u)
 ►To adjust colour temperature. You can also adjust Colour 
Temperature in the PICTURE menu.
Transmission
Data  Min : 00  to  Max : 64
* Refer to ‘Real data mapping 1’. See page 150.
[x][u][  ][Set ID][  ][Data][Cr]
Ack
[u][  ][Set ID][  ][OK/NG][Data][x]
18. Auto Configure(Command: j u)
 ►To  adjust  picture  position  and  minimize  image  shaking 
automatically. It works only in RGB (PC) mode.
Transmission
Data 01: To set
[j][u][  ][Set ID][  ][Data][Cr]
Ack
Ack
[u][  ][Set ID][  ][OK/NG][Data][x]
[q][ ][Set ID][ ][OK/NG][Data][x]
17. Energy Saving (Command: j q)
 ►To  reduce  the  power  consumption  of  the  TV.  You can also adjust Energy Saving in OPTION menu.
Transmission
[j][q][  ][Set ID][  ][Data][Cr]
Power Saving FunctionLevelDescription
76543210
0000Low Power0000Off
0000Low Power0001Minimum
0000Low Power0010Medium
0000Low Power0011Maximum
0000Low Power0101Screen Off
19.Tune Command (Command: m a)
 ►Select channel to following physical number.
Transmission
Data00 :  High channel dataData01 : Low channel data ex.  No. 47 -> 00 2F (2FH)    No. 394 -> 01 8A (18AH),    DTV No. 0 -> Don’t careData02 :  0x00 : Analogue Main     0x10 : DTV Main     0x20 : Radio
Channel data range Analogue - Min: 00 to Max: 63 (0 to 99) Digital - Min: 00 to Max: 3E7 (0 to 999)(Except For Sweden, Finland, Norway, Denmark, Ireland) Digital - Min: 00 to Max: 270F (0 to 9999)(Only Sweden, Finland, Norway, Denmark, Ireland)
[m][a][  ][Set ID][  ][Data0][  ][Data1][  ][Data2][Cr]
Ack
[a][  ][Set ID][  ][OK/NG][Data][x]
Data Min: 00 to Max: 7DH
 
						

							150
APPENDIX
APPENDIX
23. Input select (Command: x b)
   (Main Picture Input)
 ►To select input source for main picture.
Transmission
Data  Structure
[x][b][  ][Set ID][  ][Data][Cr]
22. Back Light (Command: m g)
 ►To Control the back light.
Transmission
[m][g][  ][Set ID][  ][Data][Cr]
Ack
[g][  ][Set ID][  ][OK/NG][Data][x]
Ack
[b][  ][Set ID][  ][OK/NG][Data][x]
Data : data Min: 00 to Max: 64
21. Key(Command: m c)
 ►To send IR remote key code.
Transmission
Data Key code - Refer to page 147.
[m][c][  ][Set ID][  ][Data][Cr]
Ack
[c][  ][Set ID][  ][OK/NG][Data][x]
20. Programme Add/Skip(Command: m b)
 ►To set skip status for the current Programme.
Transmission
 Data  00 : Skip            01 : Add
[m][b][  ][Set ID][  ][Data][Cr]
Ack
[b][  ][Set ID][  ][OK/NG][Data][x]
*  Real data mapping 1
00 :Step 0Tint
Step 0 : R50
A :Step 10 (Set ID 10)
Step 49 : R1
F :Step 15 (Set ID 15)Step 50 :   0
10 :Step 16 (Set ID 16)Step 51 : G1
64 :Step 100Step 100 : G50
6E :Step 110Balance
Step 0 : L50
73 :Step 115
74 :Step 116Step 49 : L1
Step 50 : 0
CF :Step 199Step 51 : R1
FE :Step 254Step 100 : R50
FF :Step 255
Colour Temperature
Step 0 : W50
Step 49 : W1
Step 50 : 0
Step 51 : C1
Step 100 : C50
Data00: DTV40: Component
10: Analogue60: RGB
20: AV90: HDMI