LG Flatron M2362dp Owners Manual

							11
PREPARATION
WALL MOUNT : HORIZONTAL INSTALLATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation
instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.
1. Be sure to use screws and a wall mount that meet VESA standards.
2. Using screws longer than those recommended might damage the product.
3. Using screws that do not meet VESA standards might either damage the product or result in it coming 
away from the wall. We will not be held responsible for any damage resulting from failure to follow these 
instructions.
4. VESA compatible only with respect to screw mounting interface dimensions and mounting screw speci-
fications
5. Please use VESA standard as below.
      5-1) 784.8 mm (30.9 inch) and under   
            * Wall Mount Pad Thickness : 2.6 mm
            * Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mm
      5-2) 787.4 mm (31.0 inch) and above 
            * Please use VESA standard wall mount pad and screws. 
10 cm
10 cm
10 cm10 cm
10 cm
Wall Mount Pad 
< Screw Mounting Interface Dimensions >
ModelM1962DP
M2062DP
M2262DP
M2362DP
M2762DP
VESA ( A x B)100 x 100200 x 100
Wall mount 
bracket(optional)
RW120RW240
   
						

							12
PREPARATION
PREPARATION
DESKTOP PEDESTAL INSTALLATION
POSITIONING YOUR DISPLAY
For proper ventilation, allow a clearance of 10 cm on each side and from the wall.
 ■The image shown may be somewhat different from your set.
 ■The image shown may be somewhat different from your set.
Adjust the position of the panel in various ways for maximum comfort.
* Tilt range
-5°15°
10 cm
10 cm
10 cm10 cm
 
						

							13
PREPARATION
LOCATION
 ■When  adjusting  the  angle  of  the  screen,  do  not  put  your 
finger(s) in between the head of the monitor and the stand 
body. 
    You can hurt your finger(s).
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken  not to 
expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a 
position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
WARNING
SWIVEL STAND(Only M2762DP)
 ■The image shown may be somewhat different from your set.
After  installing  the  set,  you  can  adjust  the  set  manually  to  the  left  or  right  direction  by  179  degrees  to 
suit your viewing position.
   
						

							14
PREPARATION
PREPARATION
SECURING THE SET TO THE WALL TO PREVENT FALLING 
WHEN THE SET IS USED ON A STAND (Only M2762DP)
 ■The image shown may be somewhat different from your set.
 ■Use  a  sturdy  rope  or  cord  (sold  separately)  to  tie  the  product.  It  is 
safer  to  tie  the  rope  so  it  becomes  horizontal  between  the  wall  and 
the product.
We recommend that you set up the set close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the set be attached to a wall so it cannot be pulled in a forward direction, 
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the set. 
 ■Insert the eye-bolts (or set brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or set brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is 
mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
NOTE
 ►When moving the set, undo the cords first.
 ►Use a platform or cabinet strong enough and large enough to support the size and weight of the set.
 ►To use the set safely make sure that the height of the bracket on the wall and the one on the set are the 
same.
!
 
						

							15
PREPARATION
WARNING
 ■The image shown may be somewhat different from your set.
The SET must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product. Use only an attached screw.
1-Screw
(provided as parts of the product)
Stand
Desk
 ►To prevent SET from falling over the SET should be securely attached to the floor/wall per installation 
instructions. Tipping,shaking, or rocking the machine may cause injury.
ATTACHING THE TV TO A DESK (Only M2762DP)
   
						

							16
PREPARATION
PREPARATION
KENSINGTON SECURITY SYSTEM
- The product is equipped with a Kensington Security System connector on the back panel. Connect the 
Kensington Security System cable as shown below.
- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided 
with the Kensington Security System.
For further information, contact http://www.kensington.com, the internet homepage of the Kensington 
company.  Kensington  sells  security  systems  for  expensive  electronic  equipment  such  as  notebook 
PCs and LCD projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a. If the product feels cold to the touch, there may be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with product.
b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the monitor’s performance.
c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
 
						

							17
EXTERNAL  EQUIPMENT  SETUP
ANTENNA CONNECTION
 ■To prevent damage do not connect to the mains outlet until all connections are made between the devices.
 ■For optimum picture quality, adjust antenna direction.
 ■An antenna cable and converter are not supplied.
Multi-family Dwellings / Apartments
(Connect to wall antenna socket)Wall
Antenna
Socket
Outdoor
AntennaSingle-family Dwellings / Houses
(Connect to wall jack for outdoor antenna)
RF Coaxial Wire (75 Ω)
 ■In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.
 ■If signal needs to be split for two sets, use an antenna signal splitter for connection.
EXTERNAL EQUIPMENT SETUP
AntennaSignal
Amplifier
UHF
VHF
   
						

							18
EXTERNAL EQUIPMENT SETUP
EXTERNAL  EQUIPMENT  SETUP
HD RECEIVER SETUP
Connecting with a component cable
 ■To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
 ■The image shown may be somewhat different from your set.
 ►HDMI Audio Supported format : Dolby Digital, PCM 
 ►DTS Audio format is not supported.
SignalComponentHDMI
480i / 576iYESNo
480p / 576pYESYES
720p / 1080iYESYES
1080pYES
(50 Hz / 60Hz only)
YES
(24 Hz / 30 Hz / 50Hz / 60Hz)
Connect the video outputs (Y, PB, PR) of the digital 
set-top box to the COMPONENT IN VIDEO jacks on 
the SET.
Connect  the  audio  output  of  the  digital  set-top  box 
to the COMPONENT IN AUDIO jacks on the SET.
Turn on the digital set-top box.
(Refer  to  the  owner’s  manual  for  the  digital  set-top 
box.)
Select COMPONENT  input  source  using  the INPUT 
button on the remote control
1
2
3
412
 
						

							19
EXTERNAL  EQUIPMENT  SETUP
Connecting a set-top box with a HDMI cable
Connect  the  digital  set-top  box  to HDMI/DVI  IN   jack 
on the SET
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
Select HDMI input source using the INPUT button on 
the remote control.
1
2
3
NOTE
 ►Check  that  your  HDMI  cable  is  High  Speed  HDMI  Cable.  If  the  HDMI  cables  are  not  High  Speed 
HDMI Cable, flickering or no screen display can result. Please use the High Speed HDMI Cable.
!
1
   
						

							20
EXTERNAL EQUIPMENT SETUP
EXTERNAL  EQUIPMENT  SETUP
Connect the digital set-top box to HDMI/DVI IN jack on the SET.
Connect the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the SET.
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
Select HDMI input source using the INPUT button on the remote control.
Connecting with an HDMI to DVI cable
1
2
3
4
1
2