LG Flatron L192ws Users Guide

							A10
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. 
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the      o r       Buttons. When the icon you want
becomes highlighted, press the  AUTO/SETButton.
Use the       /      Buttonsto adjust the item to the desired level.
Accept the changes by pressing the MENUButton.
Exit the OSD by Pressing the MENU Button.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.

On Screen Display(OSD) Selection and Adjustment 
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
You were introduced to the procedure of selecting and adjusting an item
using the OSD system.  Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
Menu Name
Icons
Button Tip
PICTURE
Sub-menus
MENU        : Exit
: Adjust (Decrease/Increase)
SET        : Enter
: Select another sub-menu
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
CLOCK
PHASE
SHARPNESS
Adjusts any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
Adjusts the focus of the display. 
This item allows you to remove any
horizontal noise and clear or sharpen
text.
Adjust the clearness of the screen.
TRACKING
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
TRACKING
HORIZONTAL
VERTICALAdjusts the screen image left and right.
Adjusts the screen image up and down.
POSITION
3hfC: Exit
: Decrease
: Increase
SET: Select another sub-menu
Tltavaly
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Troubleshooting
Check the following before calling for service.
No image appearsNo image appears
Do you see a OSD LOCKED message on the screen?
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator blue or
green?
Is the power indicator
amber?
Do you see an "OUT OF
RANGE" message on
the screen?
Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?• Check and see if the power cord is connected
properly to the power outlet.
• Press the Power button.
• Adjust the brightness and the contrast.
• If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
• Try to turn on the PC.
• This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
• This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENUbutton for several
seconds: the message 
“OSD UNLOCKED”will appear. Do you see “OSD
LOCKED” when you
push MENU button?
&ownloadedCfromCManualMonitor/comCManuals
Troubleshooting
Have you installed the display driver?
Have you installed the
display driver?
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
• Make sure to check if the video card supports
Plug&Play function.
Display image is incorrect
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Specifications
Indicator
On Mode
Sleep Mode
Off ModeGreen
Amber
Off
LED Color
MODE
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
*15
16640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
1440 x 900
1440 x 900
1440 x 90031.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.976
55.469
55.935
70.63570
70
60
75
60
75
75
60
75
75
65
60
75
60
60
75
*Recommend Mode
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							A9
Control Panel Functions
This Indicator lights up green when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes 
to amber. Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to enter a selection in the On Screen 
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SETbutton before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is
L192WS : 1440 x 900
Control Function
&ownloadedCfromCManualMonitor/comCManuals
NOTE
The order of icons may differ depending on the model (A11~A15).
On Screen Display(OSD) Selection and Adjustment 
The following table describes all the On Screen Display control, adjustment,
and setting menus.
PICTURE
COLOR
POSITION
TRACKING
SETUP
Main menu Sub menu                                  Reference
PRESET   sRGB
6500K
9300K
RED
GREEN
BLUE
To adjust the brightness,
contrast and gamma of the
screen
To adjust the position of the
screen To customize the color of the
screen
To customize the screen
status for a user's operating
environment To improve the clarity and
stability, sharpness of the
screen BRIGHTNESS
CONTRAST
GAMMA
HORIZONTAL
VERTICAL
CLOCK
PHASE
SHARPNESS
LANGUAGE
OSD
POSITION
WHITE  BALANCE
POWER INDICATOR
4:3 IN WIDE
FACTORY RESET
HORIZONTAL
VERTICAL
: Adjustable
Downloaded2from2ManualMonitorRcom2Manuals
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
BRIGHTNESS
CONTRAST 
GAMMA
Adjusts the brightness of the screen. 
Adjusts the contrast of the screen.
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
PICTURE
PRESET
RED
GREEN
BLUESelects the color temperature. 
• sRGB: Set the screen color to fit the
SRGB standard color
specification.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
Adjusts red color levels.
Adjusts green color levels.
Adjusts blue color levels.
COLOR
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
PICTURE
COLOR
&ownloadedCfromCManualMonitor/comCManuals 
						

							A10
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. 
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the      o r       Buttons. When the icon you want
becomes highlighted, press the  AUTO/SETButton.
Use the       /      Buttonsto adjust the item to the desired level.
Accept the changes by pressing the MENUButton.
Exit the OSD by Pressing the MENU Button.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.

On Screen Display(OSD) Selection and Adjustment 
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
You were introduced to the procedure of selecting and adjusting an item
using the OSD system.  Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
Menu Name
Icons
Button Tip
PICTURE
Sub-menus
MENU        : Exit
: Adjust (Decrease/Increase)
SET        : Enter
: Select another sub-menu
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
CLOCK
PHASE
SHARPNESS
Adjusts any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
Adjusts the focus of the display. 
This item allows you to remove any
horizontal noise and clear or sharpen
text.
Adjust the clearness of the screen.
TRACKING
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
TRACKING
HORIZONTAL
VERTICALAdjusts the screen image left and right.
Adjusts the screen image up and down.
POSITION
3hfC: Exit
: Decrease
: Increase
SET: Select another sub-menu
Tltavaly
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Troubleshooting
Check the following before calling for service.
No image appearsNo image appears
Do you see a OSD LOCKED message on the screen?
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator blue or
green?
Is the power indicator
amber?
Do you see an "OUT OF
RANGE" message on
the screen?
Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?• Check and see if the power cord is connected
properly to the power outlet.
• Press the Power button.
• Adjust the brightness and the contrast.
• If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
• Try to turn on the PC.
• This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
• This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENUbutton for several
seconds: the message 
“OSD UNLOCKED”will appear. Do you see “OSD
LOCKED” when you
push MENU button?
&ownloadedCfromCManualMonitor/comCManuals
Troubleshooting
Have you installed the display driver?
Have you installed the
display driver?
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
• Make sure to check if the video card supports
Plug&Play function.
Display image is incorrect
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Specifications
Indicator
On Mode
Sleep Mode
Off ModeGreen
Amber
Off
LED Color
MODE
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
*15
16640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
1440 x 900
1440 x 900
1440 x 90031.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.976
55.469
55.935
70.63570
70
60
75
60
75
75
60
75
75
65
60
75
60
60
75
*Recommend Mode
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							A9
Control Panel Functions
This Indicator lights up green when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes 
to amber. Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to enter a selection in the On Screen 
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SETbutton before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is
L192WS : 1440 x 900
Control Function
&ownloadedCfromCManualMonitor/comCManuals
NOTE
The order of icons may differ depending on the model \(A11~A15\).
On Screen Display(OSD) Selection and Adjustment 
The following table describes all the On Screen Display control, adjustment,
and setting menus.
PICTURE
COLOR
POSITION
TRACKING
SETUP
Main menu Sub menu                                  Reference
PRESET   sRGB
6500K
9300K
RED
GREEN
BLUE
To adjust the brightness,
contrast and gamma of the
screen
To adjust the position of the
screen To customize the color of the
screen
To customize the screen
status for a user's operating
environment To improve the clarity and
stability, sharpness of the
screen BRIGHTNESS
CONTRAST
GAMMA
HORIZONTAL
VERTICAL
CLOCK
PHASE
SHARPNESS
LANGUAGE
OSD
POSITION
WHITE  BALANCE
POWER INDICATOR
4:3 IN WIDE
FACTORY RESET
HORIZONTAL
VERTICAL
: Adjustable
Downloaded2from2ManualMonitorRcom2Manuals
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
BRIGHTNESS
CONTRAST 
GAMMA
Adjusts the brightness of the screen. 
Adjusts the contrast of the screen.
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
PICTURE
PRESET
RED
GREEN
BLUESelects the color temperature. 
• sRGB: Set the screen color to fit the
SRGB standard color
specification.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
Adjusts red color levels.
Adjusts green color levels.
Adjusts blue color levels.
COLOR
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
PICTURE
COLOR
&ownloadedCfromCManualMonitor/comCManuals 
						

							A10
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. 
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the      o r       Buttons. When the icon you want
becomes highlighted, press the  AUTO/SETButton.
Use the       /      Buttonsto adjust the item to the desired level.
Accept the changes by pressing the MENUButton.
Exit the OSD by Pressing the MENU Button.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.

On Screen Display(OSD) Selection and Adjustment 
NOTE
OSD \(On Screen Display\) menu languages on the monitor may differ from the manual.
You were introduced to the procedure of selecting and adjusting an item
using the OSD system.  Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
Menu Name
Icons
Button Tip
PICTURE
Sub-menus
MENU        : Exit
: Adjust (Decrease/Increase)
SET        : Enter
: Select another sub-menu
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
CLOCK
PHASE
SHARPNESS
Adjusts any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
Adjusts the focus of the display. 
This item allows you to remove any
horizontal noise and clear or sharpen
text.
Adjust the clearness of the screen.
TRACKING
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
TRACKING
HORIZONTAL
VERTICALAdjusts the screen image left and right.
Adjusts the screen image up and down.
POSITION
3hfC: Exit
: Decrease
: Increase
SET: Select another sub-menu
Tltavaly
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Troubleshooting
Check the following before calling for service.
No image appearsNo image appears
Do you see a OSD LOCKED message on the screen?
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator blue or
green?
Is the power indicator
amber?
Do you see an "OUT OF
RANGE" message on
the screen?
Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?• Check and see if the power cord is connected
properly to the power outlet.
• Press the Power button.
• Adjust the brightness and the contrast.
• If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
• Try to turn on the PC.
• This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
• This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENUbutton for several
seconds: the message 
“OSD UNLOCKED”will appear. Do you see “OSD
LOCKED” when you
push MENU button?
&ownloadedCfromCManualMonitor/comCManuals
Troubleshooting
Have you installed the display driver?
Have you installed the
display driver?
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
• Make sure to check if the video card supports
Plug&Play function.
Display image is incorrect
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Specifications
Indicator
On Mode
Sleep Mode
Off ModeGreen
Amber
Off
LED Color
MODE
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
*15
16640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
1440 x 900
1440 x 900
1440 x 90031.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.976
55.469
55.935
70.63570
70
60
75
60
75
75
60
75
75
65
60
75
60
60
75
*Recommend Mode
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							Press the       button to reset immediately.
On Screen Display(OSD) Selection and Adjustment 
A15
MENU: Exit
: Adjust
: Adjust
SET: Select another sub-menu
Main menu Sub menu Description
SETUP
SETUP
SETUP
If this does not improve the screen image, restore the factory default settings. 
If necessary, perform the white balance function again. This function will be enabled only when
the input signal is an analog signal. 
To choose the language in which the
control names are displayed.
To adjust position of the OSD window
on the screen.LANGUAGE
OSD
POSITION
WHITE
BALANCE
FACTORY
RESET
If the output of the video card is different
the required specifications, the color level
may deteriorate due to video signal
distortion. Using this function, the signal
level is adjusted to fit into the standard
output level of the video card in order to
provide the optimal image.
Activate this function when white and
black colors are present in the screen.   
POWER
INDICATOR
Restore all factory default settings except
"LANGUAGE." 
Use this function to set the power
indicator on the front side of the monitor
to ONor OFF.
If you set OFF, it will go off. 
If you set ONat any time, the power
indicator will automatically be turned on.
4:3 IN WIDETo select the image size of the screen.
WIDE4:3
Resolution        Screen ratio
1280x1024
1152x864
1024x768
800x600
640x480
720x4805 : 4
4 : 3
4 : 3
4 : 3
4 : 3
3 : 2
* 4:3 : Depending on the input video signal ratio,    
it is automatically changed to an optimized screen 
ratio. (The 1280X1024 input signal is changed 
to 5:4 ratio and 1024X768 to 4:3.)
The input signal which the 4:3 IN WIDE does not support  '4:3'   
is the following.   
-The 19 inch monitor is 720x400,1280x768,1360x768,1440x900.
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							A10
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. 
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the      o r       Buttons. When the icon you want
becomes highlighted, press the  AUTO/SETButton.
Use the       /      Buttonsto adjust the item to the desired level.
Accept the changes by pressing the MENUButton.
Exit the OSD by Pressing the MENU Button.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.

On Screen Display(OSD) Selection and Adjustment 
NOTE
OSD \(On Screen Display\) menu languages on the monitor may differ from the manual.
You were introduced to the procedure of selecting and adjusting an item
using the OSD system.  Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
Menu Name
Icons
Button Tip
PICTURE
Sub-menus
MENU        : Exit
: Adjust (Decrease/Increase)
SET        : Enter
: Select another sub-menu
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
CLOCK
PHASE
SHARPNESS
Adjusts any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
Adjusts the focus of the display. 
This item allows you to remove any
horizontal noise and clear or sharpen
text.
Adjust the clearness of the screen.
TRACKING
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
TRACKING
HORIZONTAL
VERTICALAdjusts the screen image left and right.
Adjusts the screen image up and down.
POSITION
3hfC: Exit
: Decrease
: Increase
SET: Select another sub-menu
Tltavaly
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Troubleshooting
Check the following before calling for service.
No image appearsNo image appears
Do you see a OSD LOCKED message on the screen?
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator blue or
green?
Is the power indicator
amber?
Do you see an "OUT OF
RANGE" message on
the screen?
Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?• Check and see if the power cord is connected
properly to the power outlet.
• Press the Power button.
• Adjust the brightness and the contrast.
• If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
• Try to turn on the PC.
• This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
• This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENUbutton for several
seconds: the message 
“OSD UNLOCKED”will appear. Do you see “OSD
LOCKED” when you
push MENU button?
&ownloadedCfromCManualMonitor/comCManuals
Troubleshooting
Have you installed the display driver?
Have you installed the
display driver?
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
• Make sure to check if the video card supports
Plug&Play function.
Display image is incorrect
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Specifications
Indicator
On Mode
Sleep Mode
Off ModeGreen
Amber
Off
LED Color
MODE
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
*15
16640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
1440 x 900
1440 x 900
1440 x 90031.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.976
55.469
55.935
70.63570
70
60
75
60
75
75
60
75
75
65
60
75
60
60
75
*Recommend Mode
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							A17
Troubleshooting
Display image is incorrect
Display Position is
inco\f\fect.
 On the sc\feen
backg\found, ve\ftical 
ba\fs o\f st\fipes a\fe
visible.
 Any ho\fizontal noise
appea\fing in any
image o\f cha\facte\fs
a\fe not clea\fly
po\ft\fayed.• Press the  AUTO/SET button to \butom\bti\f\bll\uy
\bdjust your displ\by i\um\bge to the ide\bl s\uetting. 
If the results \bre \uuns\btisf\b\ftory, \bdjust \uthe im\bge 
position using the  H position and V positio\tn i\fon
in the on s\freen dis\upl\by.
• Press the  AUTO/SET button to \butom\bti\f\bll\uy
\bdjust your displ\by i\um\bge to the ide\bl s\uetting.
If the results \bre \uuns\btisf\b\ftory, de\fre\u\bse the
verti\f\bl b\brs or str\uipes using the  CLOCKi\fon in
the on s\freen displ\b\uy.
• Press the  AUTO/SET button to \butom\bti\f\bll\uy
\bdjust your displ\by i\um\bge to the ide\bl s\uetting.
If the results \bre \uuns\btisf\b\ftory, de\fre\u\bse the 
horizont\bl b\brs using \uthe  PHASEi\fon in the on 
s\freen displ\by.
• Che\fk  Cont\fol Panel --> Displ\tay --> Settings
\bnd \bdjust the displ\by\u to the re\fommended\u
resolution or \bdjust \uthe displ\by im\bge t\uo the ide\bl
setting. Set the \fol\uor setting higher t\uh\bn 24 bits
(true \folor).
Important
Check  Control Panel --> Display --> Settings and see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommen\
d 
resolution .
Reasons for Recommending Optimal Resolution :  The aspect ratio is 16:10. 
If the input resolution is not 16:10 (for instance, 16:9, 5:4, 4:3), y\
ou might encounter
problems such as blurred letters, blurry screen, cut-off screen display \
or tilted screen.
The setting method can differ by computer and O/S (Operation System), \
 and resolution mentioned above may not be supported by the video card   \
 
performance. In this case, please ask to the computer or the video card \
 
manufacturer
. 
 
						

							A10
On Screen Display (OSD) Control Adjustment
Screen Adjustment
$	
%\015	




	
	
	





&\015
	



	
\(
+

,

	



\015


\015


	

	
	

	
\015	



%\015	
	
	
\015
	

\015	

\(\)
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the      o r       Buttons. When the icon you want
becomes highlighted, press the  AUTO/SETButton.
Use the       /      Buttonsto adjust the item to the desired level.
Accept the changes by pressing the MENUButton.
Exit the OSD by Pressing the MENU Button.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.

On Screen Display(OSD) Selection and Adjustment 
NOTE
OSD \(On Screen Display\) menu languages on the monitor may differ from the manual.
5
\015	

\(\)


0


	




	
	

$	\015
\012
$	\015
1
	
\015	

PICTURE
\(\0156	\015
MENU        : Exit
: Adjust (Decrease/Increase)
SET        : Enter
: Select another sub-menu
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
CLOCK
PHASE
SHARPNESS
Adjusts any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
Adjusts the focus of the display. 
This item allows you to remove any
horizontal noise and clear or sharpen
text.
Adjust the clearness of the screen.
.+*213
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
TRACKING
HORIZONTAL
VERTICALAdjusts the screen image left and right.
Adjusts the screen image up and down.
\012\(1
!*: Exit
: Decrease
: Increase
SET: Select another sub-menu
Tltavaly
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Troubleshooting
*

	

No image appearsNo image appears
Do you see a OSD LOCKED message on the screen?
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator blue or
green?
Is the power indicator
amber?
Do you see an "OUT OF
RANGE" message on
the screen?
Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?• Check and see if the power cord is connected
properly to the power outlet.
• Press the Power button.
• Adjust the brightness and the contrast.
• If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
• Try to turn on the PC.
• This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
• This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENUbutton for several
seconds: the message 
“OSD UNLOCKED”will appear. Do you see “OSD
LOCKED” when you
push MENU button?
&ownloadedCfromCManualMonitor/comCManuals
Troubleshooting
Have you installed the display driver?
Have you installed the
display driver?
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
• Make sure to check if the video card supports
Plug&Play function.
Display image is incorrect
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Zownloadedjfromj≤anual≤onitorAcomj≤anuals
Specifications
Indicator
On Mode
Sleep Mode
Off ModeGreen
Amber
Off
LED Color
MODE
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
*15
16640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
1440 x 900
1440 x 900
1440 x 90031.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.976
55.469
55.935
70.63570
70
60
75
60
75
75
60
75
75
65
60
75
60
60
75
*Recommend Mode
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							A19
Spe\fifi\f\btions       \u                  \u                  \u                  \u       
NOTEInformation in this document is subject to change without notice.
Display 
Sync \bnput
Video \bnput 
Resolution 
Plug&Play 
Powe\f 
Consumption 
Dimensions&Weight
Tilt Range 
Powe\f \bnput
Envi\fonmental 
Conditions 
Stand Base 
Powe\f co\fd 19 (48 \fm) Fl\bt P\bnel A\ftiv\ue m\btrix-TFT LCD  
Anti-Gl\bre \fo\bting
19 in\fhes view\bble
0.2835 mm pixel pit\fh
Horizont\bl Freq. 30 - 83 kHz (Autom\bti\f) Verti\f\bl Freq. 56 - 75 Hz (Autom\bti\f) 
Input Form Sep\br\bte TTL
SOG (Syn\f On Green) 
Sign\bl Input 15 pin D-Sub Conne\ftor 
Input Form RGB An\blog (0.7 Vp-p/ 75 oh\um) 
M\bx VESA 1440 x 900 @75 Hz 
Re\fommend VESA 1440 x 900 @60 Hz 
DDC 2B 
0n Mode :      34 W(Typi\f\bl)
Sleep Mode ≤ 1 W 
Off Mode ≤ 1 W
With St\bnd Without St\bnd
Width 43.48 \fm / 17.11 in\fhes 43.48 \fm / 17.11 in\fhes
Height 37.0 \fm / 14.56 in\fhes 28.73 \fm / 11.31 in\fhes
Depth 18.0 \fm /   7.09 in\fhes 5.87 \fm /   2.31 in\fhes 
Net 4.16 kg (9.17 lbs) 
Tilt -5˚~20˚ 
AC 100-240V~ 50/60Hz 0.8A  
Oper\bting Conditions Temper\bture 10˚C to 35 ˚C 
Humidit y 10 % to 80 % non-Condensi\ung
Stor\bge Conditions Temper\bture -20˚C to 60 ˚C
Humidity 10 % to 90 % non-Condensi\ung
Att\b\fhed(     ), Det\b\fh\ued ( O ) 
W\bll-outlet type or \uPC-outlet type
Zownloadedjfromj≤anual≤onitorAcomj≤anuals