LG Flatron L192ws Users Guide

							Make sure to read the Important Precautionsbefore using this product. 
Keep the User's Guide(CD) in an accessible place for furture reference.
Have the model and serial number ready when calling for support.
L192WS
LCD Computer Monitor
User’s Guide
 
						

							A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.
Do not Open the Display.
There are no user serviceable components inside. 
There are Dangerous High Voltages inside, even when the power is OFF. 
Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not drop an object on or apply impact to the product. Do not throw any toys
or objects on the product screen. 
It can cause injury to human, problem to product and damage the display.  
To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the displays cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
When the display is to be left unattended for an extended period of time, unplug
it from the wall outlet.
In the presence of thunder and lightning, never touch the power cord and signal
cable because it can be very dangerous. It can cause electric shock. 
Important Precautions
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							A2
Import\bnt Pre\f\butions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do n\
ot place the 
display where the power cord is subject to damage. 
Do not use this display near water such as near a bathtub, washbowl, kit\
chen sink, 
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow \
the release of
heat generated during operation. If these openings are blocked, built-up\
 heat can
cause failures which may result in a fire hazard. Therefore, NEVER:Block the bottom ventilation slots by placing the display on a bed, sofa\
, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is p\
rovided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this ma\
y scratch, 
mar, or damage the Active Matrix LCD permanently. 
Do not press the LCD screen with your finger for a long time as this may\
 cause 
some afterimages. 
Some dot defects may appear as Red, Green or Blue spots on the screen. 
However, this will have no impact or effect on the display performance. \
 
If possible, use the recommended resolution to obtain the best image qua\
lity for 
your LCD display. If used under any mode except the recommended resoluti\
on,
some scaled or processed images may appear on the screen. However, this \
is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on\
 the displayscreen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to anot\
her
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mer\
cury.
Do not dispose of this product with general household waste.Disposal of this product must be carried out in accordance to the regula\
tions of
your local authority.
 
						

							Connecting the Display
A3
Important
Do not remove and re-install the stand frequently, it could damage the stand.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1. Place the monitor with its front facing downward on a soft cloth.
2.Assemble the Stand Body into the product in the correct direction as shown in the picture.     
Make sure you push it until you hear it “click”. 
3.Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.
R
E
A
R
R
E
A
RREAR
REAR
FRONT
FRONT
4.Once assembled take the monitor up carefully and face the front side
 
						

							A4
Connecting the Display
1.Put a cushion or soft cloth on a flat surface.
To remove the Stand: 
2. Place  the  monitor  face  down  on
the cushion or soft cloth.     
3.Hold the product as it follows and lift up the Stand slightly.
4.Change your hold on the product as it follows and turn the Stand Base in the arrow
direction until you hear a "click."
5.Pull out the Stand to remove.
The Head part
The Stand 
base part
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							Connecting the Display
A5
To remove the Stand Base: 
2.
The body of the Stand and the Stand Base are successfully separated.
1.Separate the Stand Body by lifting it as pressing the arrow on the Stand Body while holding
the Stand Base with the other hand.
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							A6
Connecting the Display
20
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚                            
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
When adjusting the angle of the screen, do not put your finger(s)
in between the head of the monitor and the stand body . 
You can hurt your finger(s).Warning:
 
						

							2
1
A7
Conne\fting the Displ\u\by
1.Place the monitor in a convenient, well-ventilated location near your co\
mputer. 2.Connect the signal cable. When attached, tighten the thumbscrews to secure the 
connection.
3.Connect the power cord into a proper power outlet  that is easily access\
ible and close to
the display.
Wall-outlet type
PC-outlet type
MAC
Powe\f Co\fd Signal Cable
Va\fies acco\fding to mod\tel.
1
2
Mac adapte\fFor Appl\b Mac\fntosh u\ns\b, a  s\bparat\b plug \nadapt\br \fs n\b\bd\bd to c\nhang\b 
th\b 15 p\fn h\fgh d\bns\ft\ny (3 row) D-sub VGA\n conn\bctor on th\b sup\npl\f\bd
cabl\b to a 15 p\fn  2 r\now conn\bctor.
4.Press        button on the rear switch panel to turn the power on.
When monitor power is turned on, the 
Self Image Setting
Function
is executed automatically.
NOTE  This is \b simplifie\ud represent\btion of the re\br view. 
This re\br view repr\uesents \b
gener\bl model; your d\uispl\by m\by
differ from the vi\uew \bs shown.
PC
PC
Using the Computer
NOTE‘ Self Image Setting Function’? 
This function provides the user with optimal display settings.When the u\
ser
connects the monitor for the first time, this function automatically adj\
usts the display to optimal settings for individual 
input signals. 
‘AUTO/SET’ Function?  When you encounter problems such as blurry screen, blurred letters, scre\
en flicker or tilted
screen while using the device or after changing screen resolution, press\
 the AUTO/SET function button to improve
resolution. 
 
						

							A8
Control Panel Functions
MENU ButtonUse this button to enter or exit the On Screen Display.
Control Function
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU buttonfor several seconds.
The message "OSD LOCKED"should appear.
You can unlock the OSD controls at any time by pushing
the MENU buttonfor several seconds. The message
"OSD UNLOCKED"should appear.
ButtonsUse these buttons to select or adjust functions in the On
Screen Display.
LightView hot key
Front Panel ControlsRear
DAY
NIGHTThis feature lets you easily select the best desired
image condition optimized to the environment
(ambient illumination, image types etc).
• DAY: Bright ambient illumination
• NIGHT: Dark ambient illumination
• TEXT: For text images (Word processing etc.)
• MOVIE : For animation images in videos 
or movies 
• PHOTO : For pictures or drawings
• 
NORMAL: This is under normal operating
conditions
Zownloadedjfromj≤anual≤onitorAcomj≤anuals 
						

							A9
Control Panel Functions
This Indicator lights up green when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes 
to amber. Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to enter a selection in the On Screen 
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SETbutton before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is
L192WS : 1440 x 900
Control Function
&ownloadedCfromCManualMonitor/comCManuals
NOTE
The order of icons may differ depending on the model \(A11~A15\).
On Screen Display(OSD) Selection and Adjustment 

	




	
\(
	
	
	\015
\012*-./
*0.
\012\(1
.+*213
\(/-\012
Main menu Sub menu                                  Reference
PRESET   sRGB
6500K
9300K
RED
GREEN
BLUE
To adjust the brightness,
contrast and gamma of the
screen
To adjust the position of the
screen To customize the color of the
screen
To customize the screen
status for a user's operating
environment To improve the clarity and
stability, sharpness of the
screen BRIGHTNESS
CONTRAST
GAMMA
HORIZONTAL
VERTICAL
CLOCK
PHASE
SHARPNESS
LANGUAGE
OSD
POSITION
WHITE  BALANCE
POWER INDICATOR
4:3 IN WIDE
FACTORY RESET
HORIZONTAL
VERTICAL
4
+%\015

On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
BRIGHTNESS
CONTRAST 
GAMMA
Adjusts the brightness of the screen. 
Adjusts the contrast of the screen.
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
\012*-./
PRESET
RED
GREEN
BLUESelects the color temperature. 
• sRGB: Set the screen color to fit the
SRGB standard color
specification.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
Adjusts red color levels.
Adjusts green color levels.
Adjusts blue color levels.
*0.
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
MENU: Exit
: Decrease
: Increase
SET: Select another sub-menu
PICTURE
COLOR
&ownloadedCfromCManualMonitor/comCManuals