Lexmark X940e Owners Manual

Repair information4-239
 7510
Go Back Previous
Next
1X 500-sheet drawer (1TM) removals 
1X 500-sheet drawer (1TM)
—top cover removal 
1. Pull out tray 2 assembly (A). 
2. Remove the two screws securing the top cover (B). 
3. Remove the top cover (B).  

4-240Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—front door removal 
1. Open the 1TM front door.
2. Remove the four screws securing the front door (A) to the machine. 
3. Remove the front door (A). 
1X 500-sheet drawer (1TM)—foot cover removal 
1. Open the 1TM front door.
2. Remove the two screws securing the foot cover (A) to the machine. 
3. Remove the foot cover (A).  

Repair information4-241
 7510
Go Back Previous
Next
1X 500-sheet drawer (1TM)—right cover removal 
1. Remove the four screws securing the right cover (A). 
2. Remove the right cover (A) by lifting up and out in the direction of the arrow.  

4-242Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—tray module left cover removal 
1. Remove the four screws securing the tray module left cover (A). 
2. Remove the tray module left cover (A). 
1X 500-sheet drawer (1TM)—rear cover removal 
1. Remove the four screws securing the rear cover (A). 
2. Remove the rear cover (A). 
A 

Repair information4-243
 7510
Go Back Previous
Next
1X 500-sheet drawer (1TM)—caster removal 
1. Remove the media tray 2 assembly.
2. Place the right side of the drawer down. 
3. Remove the three screws securing the caster (A). 
4. Remove the caster (A). 
1X 500-sheet drawer (1TM)—media feed unit assembly removal (tray 2)
1. Remove the media tray 2 assembly.
2. Open the 1TM left door assembly.
3. Release the harness from the clamp.
4. Disconnect the connector from the media feed unit assembly (A).
5....

4-244Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—sensor (tray 2 feed-out) removal 
1. Open the 1TM left door assembly.
2. Remove the two screws securing bracket (A) to the machine.
3. Remove the bracket (A).
4. Disconnect the connector from the sensor (tray 2 feed-out) (B).
5. Release the hooks securing the sensor (tray 2 feed-out) (B) to the bracket (B).
6. Remove the sensor (tray 2 feed-out) (B).
AConnector
Hook
B
Actuator 

Repair information4-245
 7510
Go Back Previous
Next
1X 500-sheet drawer (1TM)—switch (media size) removal 
1. Remove the media tray 2 assembly.
2. Open the 1TM front door.
3. Disconnect the connector from the switch (media size) (A). 
4. Remove the screw securing the switch (media size) (A). 
5. Remove the switch (media size) (A).  

4-246Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—media feed lift motor removal  
1. Remove the media feed unit assembly. See “1X 500-sheet drawer (1TM)—media feed unit assembly 
removal (tray 2)” on page 4-243. 
2. Disconnect the harness from the media feed lift motor (A). 
3. Remove the two screws securing the media feed lift motor to the media feed unit assembly (B). 
4. Remove the media feed lift motor (B). 
1X 500-sheet drawer (1TM)—one-way clutch / gear assembly removal 
1....

Repair information4-247
 7510
Go Back Previous
Next
6. Remove the tray lift one-way gear 24 tooth (C). 
Replacement note:  Before re-installing, ensure all gears and washers are securely attached to the bracket 
(A). 
Harness
A
RearC Washer 

4-248Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—media out actuator removal 
1. Remove the media feed unit assembly. See “1X 500-sheet drawer (1TM)—media feed unit assembly 
removal (tray 2)” on page 4-243.
2. Release the two bosses on the media out actuator (A) from the media feed unit assembly. 
3. Remove the media out actuator (A). 
Front
Bosses
Lower viewA