Lexmark X940e Owners Manual

Repair information4-189
 7510
Go Back Previous
Next
2000-sheet dual input (TTM) switch (media size) removal
Note:  This procedure can be applied to tray 1 or tray 2 switch (media size). 
1. Remove media Tray 1 and media Tray 2. 
2. Remove one screw securing the switch (media size) (A) to the bracket inside the machine. 
3. Remove the connector from switch (media size) (A). 
4. Remove the switch (media size) (A). 
2000-sheet dual input (TTM)—switch (TTM media size) removal 
Note:  This removal procedure...

4-190Service Manual 7510 
Go Back Previous
Next
2000-sheet dual input (TTM)—media feed unit assembly 2 removal
1. Remove the media tray 2.
2. Open the TTM left door assembly.
3. Disconnect the connector from the media feed unit assembly (A).
4. Release the harness from the clamp.
5. Remove the two screws securing the media feed unit assembly (A) to the machine.
6. Remove the media feed unit assembly.
2000-sheet dual input (TTM)—media feed unit assembly removal (tray 3) 
1. Remove the tray module left...

Repair information4-191
 7510
Go Back Previous
Next 

4-192Service Manual 7510 
Go Back Previous
Next
2000-sheet dual input (TTM)—sensor (tray 3 feed-out) removal  
1. Open the TTM left door assembly. 
2. Remove the two screws securing the two support straps (A) to the machine. 
3. Disconnect the connector to the bracket (B). 
4. Remove the two screws securing the bracket (B) to the machine.
5. Remove the bracket (B). 
6. Release the hooks securing the sensor (tray 3 feed-out) (C) to the bracket (B). 
7. Remove the sensor (tray 3 feed-out) (C).  

Repair information4-193
 7510
Go Back Previous
Next
2000-sheet dual input (TTM)—sensor (tray 2 feed-out) removal 
1. Open the TTM left door assembly.
2. Remove the two screws securing bracket (A) to the machine.
3. Remove the bracket (A).
4. Disconnect the connector from the sensor (tray 2 feed-out) (B).
5. Release the hooks securing the sensor (tray 2 feed-out) (B) to the bracket (A).
6. Remove the sensor (tray 2 feed-out) (B).
2000-sheet dual input (TTM)—media feed lift motor removal  
1. Remove the...

4-194Service Manual 7510 
Go Back Previous
Next
8. Remove the media feed lift motor (B). 
AB
Connector
Rear 

Repair information4-195
 7510
Go Back Previous
Next
2000-sheet dual input (TTM)—one-way clutch / gear assembly removal 
1. Remove the tray module left cover. See “2000-sheet dual input (TTM)— tray module left cover removal” 
on page 4-174. 
2. Remove the TTM media tray 3 assembly. See “2000-sheet dual input (TTM)—TTM media tray 3 
assembly removal” on page 4-178.
3. Remove the TTM media tray 4 assembly. See “2000-sheet dual input (TTM)—TTM media tray 4 
assembly removal” on page 4-177.
4. Remove the tray...

4-196Service Manual 7510 
Go Back Previous
Next
10. Remove the tray lift one-way gear 24 tooth (C). 
Replacement note:  Before re-installing, ensure all gears and washers are securely attached to the bracket 
(A). 
Harness
A
RearC Washer 

Repair information4-197
 7510
Go Back Previous
Next
2000-sheet dual input (TTM)—media out actuator removal 
1. Remove the tray module left cover. See “2000-sheet dual input (TTM)— tray module left cover removal” 
on page 4-174. 
2. Remove the TTM media tray 3 assembly. See “2000-sheet dual input (TTM)—TTM media tray 3 
assembly removal” on page 4-178.
3. Remove the TTM media tray 4 assembly. See “2000-sheet dual input (TTM)—TTM media tray 4 
assembly removal” on page 4-177.
4. Remove the tray 4 media...

4-198Service Manual 7510 
Go Back Previous
Next
2000-sheet dual input (TTM)—sensor (media level) removal 
1. Remove the tray module left cover. See “2000-sheet dual input (TTM)— tray module left cover removal” 
on page 4-174. 
2. Remove the TTM media tray 3 assembly. See “2000-sheet dual input (TTM)—TTM media tray 3 
assembly removal” on page 4-178.
3. Remove the TTM media tray 4 assembly. See “2000-sheet dual input (TTM)—TTM media tray 4 
assembly removal” on page 4-177.
4. Remove the tray 4 media...