Lexmark X940e Owners Manual

Repair information4-179
 7510
Go Back Previous
Next
2000-sheet dual input (TTM)—tray 3 rear cable assembly removal 
1. Remove the tray module left cover. See “2000-sheet dual input (TTM)— tray module left cover removal” 
on page 4-174. 
2. Remove the TTM media tray 3 assembly. See “2000-sheet dual input (TTM)—TTM media tray 3 
assembly removal” on page 4-178.
3. Remove the tray 3 front cover. See “2000-sheet dual input (TTM)—tray 3 front cover removal” on 
page 4-178. 
4. Remove the E-clip with a prying...

4-180Service Manual 7510 
Go Back Previous
Next
7. Move the rear lift cable pulley (D) toward the rear of the tray to release the two tray 3 rear cables (E) from the 
tray lift shaft assembly (B).
8. Remove the two tray 3 rear cables (E) from the tray lift shaft assembly (B). 
9. Remove two E-clips with a prying tool securing the two small pulleys (F) on the rear of the frame assembly. 
10. Remove the two small guides (G) and the two small pulleys (F). 
11. Remove the E-clip with a prying tool securing...

Repair information4-181
 7510
Go Back Previous
Next
2000-sheet dual input (TTM)—tray 3 front cable assembly removal 
1. Remove the tray module left cover. See “2000-sheet dual input (TTM)— tray module left cover removal” 
on page 4-174. 
2. Remove the TTM media tray 3 assembly. See “2000-sheet dual input (TTM)—TTM media tray 3 
assembly removal” on page 4-178.
3. Remove the tray 3 front cover. See “2000-sheet dual input (TTM)—tray 3 front cover removal” on 
page 4-178.
4. Remove the E-clip with a prying...

4-182Service Manual 7510 
Go Back Previous
Next
2000-sheet dual input (TTM)—TTM media tray 4 front cover removal 
1. Pull out the TTM media tray 4 assembly. 
2. Remove the four screws securing the TTM tray 4 front cover (A). 
3. Remove the TTM tray 4 front cover (A).
4. Remove the six screws securing the bracket (B) to the tray.
5. Remove the bracket (B).
2000-sheet dual input (TTM)—TTM tray 4 media transport assembly removal 
1. Remove the TTM media tray 4 assembly. See “2000-sheet dual input (TTM)—TTM...

Repair information4-183
 7510
Go Back Previous
Next
5. Gently move the tray lift shaft assembly (B) toward the rear of the tray and detach the rear bushing (C) from 
the frame. 
Note:  Do not remove the front lift cable pulley (A), or the front lift cables will become detached.
6. Move the rear portion of the tray lift shaft assembly (B) away from the frame.
7. Move the rear the rear lift cable pulley (E) toward the rear of the tray to release the two tray 4 rear cables (D) 
from the tray lift shaft...

4-184Service Manual 7510 
Go Back Previous
Next
12. Remove the tray 4 rear cables (D) from the bottom plate (H).
Replacement note:  Before re-installing: 
–It is recommended that all four cables be replaced. 
–Ensure tray 4 rear cables (D) are not twisted or kinked. 
–Route the cables properly as shown in the figure. 
–Replace the cables by setting the frame assembly on its side as shown in the figure.  

Repair information4-185
 7510
Go Back Previous
Next
2000-sheet dual input (TTM)—tray 4 front cables removal 
1. Remove the TTM media tray 4 assembly. See “2000-sheet dual input (TTM)—TTM media tray 4 
assembly removal” on page 4-177.
2. Remove the tray 4 front cover. See “2000-sheet dual input (TTM)—TTM media tray 4 front cover 
removal” on page 4-182.
3. Place the TTM media tray 4 assembly on its right side, as shown in the figure. 
4. Remove the E-clip with a prying tool securing the front tray lift...

4-186Service Manual 7510 
Go Back Previous
Next
10. Remove the tray 4 front cables (C) from the bottom plates (F). 
Replacement note:  Before re-installing: 
–It is recommended that all four cables be replaced. 
–Ensure tray 4 front cables (C) are not twisted or kinked. 
–Route the cables properly as shown in the figure. 
–Replace the cables by setting the frame assembly (B) on its side as shown in the figure. 
2000-sheet dual input (TTM)—media feed unit assembly removal (tray 4)
1. Remove the media tray...

Repair information4-187
 7510
Go Back Previous
Next
7. Remove the two screws securing the media feed unit assembly (A).
8. Remove one screw securing the front bracket (B) to the machine. 
9. Remove the front bracket (B). 
10. Move the media feed unit assembly (A) to the left and up in the direction of the arrow.
11. Remove the media feed unit assembly (A).
12. Remove the two screws securing the lower guide (C) to the media feed unit assembly (A). 
13. Remove the lower guide (C). 
14. Remove the two...

4-188Service Manual 7510 
Go Back Previous
Next
2000-sheet dual input (TTM)—sensor (tray 4 feed-out) removal 
1. Remove the media tray 2 assembly.
2. Remove the tray module left cover. See “2000-sheet dual input (TTM)— tray module left cover removal” 
on page 4-174. 
3. Remove the TTM media tray 3 assembly. See “2000-sheet dual input (TTM)—TTM media tray 3 
assembly removal” on page 4-178.
4. Remove the TTM media tray 4 assembly. See “2000-sheet dual input (TTM)—TTM media tray 4 
assembly removal” on...