Lexmark X940e Owners Manual

Repair information4-249
 7510
Go Back Previous
Next
1X 500-sheet drawer (1TM)—sensor (media level) removal 
1. Remove the media feed unit assembly. See “1X 500-sheet drawer (1TM)—media feed unit assembly 
removal (tray 2)” on page 4-243. 
2. Disconnect the connector from the sensor (media level) (A). 
3. Release the hooks securing the sensor (media level) (A) to the media feed unit assembly. 
4. Remove the sensor (media level) (A). 
Front
Harness
Hooks
Lower viewA 

4-250Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—sensor (media out) removal 
1. Remove the media feed unit assembly. See “1X 500-sheet drawer (1TM)—media feed unit assembly 
removal (tray 2)” on page 4-243. 
2. Remove the media out actuator. See “1X 500-sheet drawer (1TM)—media out actuator removal” on 
page 4-248.
3. Disconnect the connector from the sensor (media out) (A). 
4. Release the hooks securing the sensor (media out) (A) to the media feed unit assembly. 
5. Remove the...

Repair information4-251
 7510
Go Back Previous
Next
1X 500-sheet drawer (1TM)—feed roll removal
1. Remove the media tray assembly. 
2. Move the feed unit front guide (A) toward the front in the direction of the arrow. 
3. Release the hook securing the feed roll (B) to the shaft (C). 
4. Remove the feed roll (B). 
Note:  Do not touch the rubber surface of the feed roll (B). 
Replacement note:  Before re-installing, do not touch the rubber surface of the feed roll (B).  

4-252Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—feed roll one-way clutch removal 
1. Remove the media tray assembly. 
2. Remove the feed roll. See “2000-sheet dual input (TTM)—feed roll removal” on page 4-200.
3. Remove the feed roll one-way clutch (A) from the shaft (B).  

Repair information4-253
 7510
Go Back Previous
Next
1X 500-sheet drawer (1TM)—one-way 22 tooth removal 
1. Remove the media tray assembly. 
2. Remove the feed roll. See “1X 500-sheet drawer (1TM)—feed roll removal” on page 4-251.
3. Remove the feed roll one-way clutch. See “1X 500-sheet drawer (1TM)—feed roll one-way clutch 
removal” on page 4-252.
4. Remove the feed roll one-way gear 22 tooth (A).  

4-254Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—separation roll one-way friction clutch removal 
1. Remove the media tray assembly. 
2. Remove the separation roll. See “1X 500-sheet drawer (1TM)—separation roll removal” on page 4-255.
3. Remove the separation roll spacer (A). 
4. Remove the separation roll one-way friction clutch (B). 
B
A
Seal
Sea 

Repair information4-255
 7510
Go Back Previous
Next
1X 500-sheet drawer (1TM)—separation roll removal 
1. Remove the media tray assembly. 
2. Move the feed unit front guide (A) toward the front in the direction of the arrow. 
3. Release the hook securing the separation roll (B) to the shaft (C). 
4. Remove the separation roll (B). 
Note:  Do not touch the rubber surface of the feed roll (B). 
Replacement note:  Before re-installing, do not touch the rubber surface of the separation roll (B). 

4-256Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—pick roll removal 
1. Remove the media tray assembly. 
2. Move the front guide (A) toward the front in the direction of the arrow. 
3. Release the hook securing the pick roll (B) to the shaft (C). 
4. Remove the pick roll (B). 
Note:  Do not touch the rubber surface of the feed roll (B).
Replacement note:  Before re-installing, do not touch the rubber surface of the pick roll (B). 

Repair information4-257
 7510
Go Back Previous
Next
1X 500-sheet drawer (1TM)—tray module left door assembly removal 
1. Open the 3TM/TMM left door assembly. 
2. Remove the two screws securing the two supports straps (A) to the machine. 
3. Remove the screw securing the bracket (B) to the machine. 
4. Remove the bracket (B). 
5. Move the tray module left door assembly (C) to the front and out in the direction of the arrow. 
6. Remove the tray module left door assembly (C). 
Front
B
A
C 

4-258Service Manual 7510 
Go Back Previous
Next
1X 500-sheet drawer (1TM)—switch (tray module left door interlock) removal 
1. Open the 1TM left door assembly. 
2. Remove the screw securing the support strap (A) to the machine.
3. Remove the screw securing the bracket (B) to the machine. 
4. Remove the bracket (B). 
5. Disconnect the two connectors from the switch (tray module left door interlock) (C). 
6. Remove the two screws securing the switch (tray module left door interlock) (C) to the bracket...