Lexmark X860de User Manual

10Close the front door.
Note: After you insert the photoconductor and close all the doors, the printer performs a motor cycle and clears the
Replace Photoconductor warnings.
The printer returns to the Ready state.
Moving the printer
Before moving the printer
CAUTION—POTENTIAL INJURY: The printer weight is greater than 55kg (121 lbs), and requires at least four
persons or a properly rated mechanical handling system to move it safely.
Maintaining the printer211
Downloaded From ManualsPrinter.com Manuals 

Follow these guidelines to avoid personal injury or printer damage:
Use at least four people or a properly rated mechanical handling system to lift the printer.
Turn the printer off using the power switch, and then unplug the power cord from the wall outlet.
Disconnect all cords and cables from the printer before moving it.
Remove all printer options before moving the printer.
Warning—Potential Damage: Damage to the printer caused by improper moving is not covered by the printer
warranty.
Removing the...

3Place the tray into the printer.
4Remove the cable cover.
Maintaining the printer213
Downloaded From ManualsPrinter.com Manuals 

5Disconnect the optional drawer connector.
6Attach the cable cover.
7Lift the printer off the trays. Maintaining the printer214
Downloaded From ManualsPrinter.com Manuals 

Moving the printer to another location
The printer and options can be safely moved to another location by following these precautions:
Any cart used to move the printer must have a surface able to support the full footprint of the printer. Any cart
used to move the options must have a surface able to support the dimensions of the options.
Keep the printer in an upright position.
Avoid severe jarring movements.
Shipping the printer
When shipping the printer, use the original packaging or call the place of...

Administrative support
Finding advanced networking and administrator information
This chapter covers basic administrative support tasks. For more advanced system support tasks, see the Networking
Guide on the Software and Documentation CD and the Embedded Web Server Administrators Guide on the Lexmark
Web site at www.lexmark.com.
Using the Embedded Web Server
If the printer is installed on a network, the Embedded Web Server is available for a range of functions including:
Viewing a virtual display of the...

Checking the device status
Using the Embedded Web Server, you can view paper tray settings, the level of toner in the print cartridge, the
percentage of life remaining in the maintenance kit, and capacity measurements of certain printer parts. To view the
device status:
1Type the printer IP address in the address field of your Web browser.
Note: If you do not know the IP address of the printer, then print a network setup page and locate the IP
address in the TCP/IP section.
2Click Device Status.
Setting...

3Touch Settings.
4Touch General Settings.
5Touch the down arrow until Screen Brightness appears.
6Touch the arrows to increase or decrease the brightness.
Brightness settings can be adjusted from 20–100 (100 is the factory default setting).
7Touch Submit.
8Touch .
Restoring the factory default settings
If you want to retain a list of the current menu settings for reference, then print a menu settings page before you restore
the factory default settings. For more information, see “Printing a menu settings...

Troubleshooting
Solving basic problems
Solving basic printer problems
If there are basic printer problems, or the printer is unresponsive, make sure:
The power cord is plugged into the printer and a properly grounded electrical outlet.
The electrical outlet is not turned off by any switch or breaker.
The printer is not plugged into any surge protectors, uninterrupted power supplies, or extension cords.
Other electronic equipment plugged into the outlet is working.
The printer is turned on. Check the...

Understanding printer messages
An error has occured with the Flash Drive. Please remove and re-insert the drive.
Try one or more of the following:
Remove and reinsert the flash drive.
If the error message remains, the flash memory may be defective and require replacing.
Change  to 
You can change the current paper source for the remainder of the print job. The formatted page will print on the paper
loaded in the selected tray. This may cause clipping of text or images. Try one or more of the following:...