Lexmark X860de User Manual

51 Defective flash detected
Try one or more of the following:
Touch Continue to clear the message and continue printing.
Cancel the current print job.
52 Not enough free space in flash memory for resources
Try one or more of the following:
Touch Continue to clear the message and continue printing.
Downloaded fonts and macros not previously stored in flash memory are deleted.
Delete fonts, macros, and other data stored in flash memory.
Upgrade to a larger capacity flash memory card.
53 Unformatted flash...

Upgrade (flash) the network firmware in the printer or print server.
55 Unsupported option in slot 
 is a slot on the printer system board.
Try one or more of the following:
1Turn the printer power off.
2Unplug the power cord from the wall outlet.
3Remove the unsupported option card from the printer system board.
4Connect the power cord to a properly grounded outlet.
5Turn the printer power back on.
56 Parallel port  disabled
 is the number of the parallel port.
Try one or more of the following:
Touch...

56 USB port  disabled
 is the number of the USB port.
Try one or more of the following:
Touch Continue to clear the message.
The printer discards any data received through the USB port.
Make sure the USB Buffer menu item is not set to Disabled.
57 Configuration change, held jobs were not restored
Since the time the jobs were stored on the printer hard disk something has changed in the printer to invalidate the
held jobs. Possible changes include:
The printer firmware has been updated.
Paper input,...

4Connect the power cord to a properly grounded outlet.
5Turn the printer back on.
58 Too many trays attached
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the additional trays.
4Connect the power cord to a properly grounded outlet.
5Turn the printer back on.
61 Remove defective disk
Try one or more of the following:
Touch Continue to clear the message and continue printing.
Install a different printer hard disk before performing any operations that require a printer hard...

84 Photoconductor low
1Press the up or down arrow button until Continue appears, and then press .
2Order a replacement photoconductor immediately. When print quality is reduced, install the new photoconductor.
84 Replace photoconductor
The printer will not print any more pages until the photoconductor is replaced.
Replace the specified photoconductor.
84 Photoconductor abnormal
An unacceptable photoconductor has been installed in the device. Replace the photoconductor.
88 Cartridge low
The toner is low....

Do not load a tray while the printer is printing. Load it prior to printing, or wait for a prompt to load it.
Do not load too much paper. Make sure the stack height does not exceed the indicated maximum height.
Make sure the guides in the tray or the multipurpose feeder are properly positioned and are not pressing too tightly
against the paper or envelopes.
Push the tray in firmly after loading paper.
Paper recommendations

Use only recommended paper or specialty media.
Do not load wrinkled, creased,...

K
H
G
F
J
Jam numbersWhat to do
200–202Open Door A, and then remove the jam.
203Open Doors A and E, and then remove any jams.
230Lower the duplex unit (Door D), and then remove the jam. Open Doors A and E, and then remove any jams.
231Lower the duplex unit (Door D), and then remove the jam. Open Door A, and then remove the jam.
24x Open each tray, and then remove any jams.
250
1Remove all media from the multipurpose feeder.
2Flex and stack the media.
3Reload the multipurpose feeder.
4Adjust the paper...

200–201 paper jams
1Open Door A by pushing the release latch up and lowering the door.
CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching.
2Pull the jam up and toward you.
Note: If the jam does not move immediately, stop pulling. Push down and pull the green lever to make it easier
to remove the jam. Make sure all paper fragments are removed.
3Close Door A. Troubleshooting238
Downloaded From...

202 paper jam
1Open Door A by pushing the release latch up and lowering the door.
CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching.
2Pull the jam up and toward you.
Note: If the jam does not move immediately, stop pulling. Push down and pull the green lever to make it easier
to remove the jam. Make sure all paper fragments are removed.
3Close Door A. Troubleshooting239
Downloaded From...

203, 230–231 paper jams
203 paper jam
1
Open Door A by pushing the release latch up and lowering the door.
CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching.
2Open Door E by pushing the release latch and lowering the door.
Troubleshooting240
Downloaded From ManualsPrinter.com Manuals