Lexmark X860de User Manual

Cleaning the scanner glass
Clean the scanner glass if you encounter print quality problems, such as streaks on copied or scanned images.
1Slightly dampen a soft, lint-free cloth or paper towel with water.
2Open the scanner cover.
12
34
1White underside of the ADF cover
2White underside of the scanner cover
3Scanner glass
4ADF glass
3Wipe the areas shown and let them dry.
4Close the scanner cover.
Adjusting scanner registration
Scanner Registration is a process to align the scan area with the paper...

7Touch the up or down arrow until Scanner Manual Registration appears.
8Touch Scanner Manual Registration.
9Touch the left and right arrows to change the settings.
10Touch Submit.
Storing supplies
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you
are ready to use them.
Do not expose supplies to:
Direct sunlight
Temperatures above 35°C (95°F)
High humidity above 80%
Salty air
Corrosive gases
Heavy dust
Conserving supplies
There are...

1Type the printer IP address into the address field of your Web browser.
Note: If you do not know the IP address of the printer, print a network setup page and locate the IP address in
the TCP/IP section.
2Click Device Status. The Device Status page appears, displaying a summary of supply levels.
Ordering supplies
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies
dealers in your area. In other countries or regions, visit the Lexmark Web...

Ordering staple cartridges
When Staples Low or Staples Empty appears, order the specified staple cartridge.
For more information, see the illustrations inside the stapler door.
Part namePart number
Staple Cartridges–3 pack 25A0013
Ordering a cleaning kit
Use the wet and dry wipes from the cleaning kit to clean the scanner glass and touch screen.
Part namePart number
Cleaning kit (wet and dry wipes) 40X0392
Replacing supplies
Replacing the toner cartridge
When 88 Cartridge low, 88.yy Replace cartridge, or...

3Grasp the handle and pull out the cartridge.
4Unpack a new cartridge.
Warning—Potential Damage: When replacing a toner cartridge, do not leave the new cartridge exposed to
direct light for an extended period of time. Extended light exposure can cause print quality problems.
5Firmly shake the cartridge side-to-side several times to redistribute the toner.
Maintaining the printer205
Downloaded From ManualsPrinter.com Manuals 

6Insert the new cartridge into the printer. Push the toner cartridge in as far as it will go. The cartridge clicks into
place when correctly installed.
7Close the front door.
Replacing the photoconductor
You can determine approximately how full the photoconductor is by printing the printer settings configuration sheet.
This helps you decide when you might need to order replacement supplies.
To ensure print quality and to avoid damage to the printer, the printer stops operating after the photoconductor...

When 84 Replace photoconductor or 84 Photoconductor low appears, order a new photoconductor
immediately. While the printer may continue to function properly after the photoconductor has reached its official
end‑of‑life, print quality significantly decreases.
To replace the photoconductor:
1Turn the printer off.
2Open the front door.
Note: The photoconductor cannot be pulled out if Side Door A is closed. Maintaining the printer207
Downloaded From ManualsPrinter.com Manuals 

3Lower Side Door A.
4Pull the photoconductor out of the printer.
Place the photoconductor on a flat, clean surface.
5Unpack the new photoconductor.
Maintaining the printer208
Downloaded From ManualsPrinter.com Manuals 

6Align and insert the end of the photoconductor.
7Remove the tape from the top of the photoconductor.
Maintaining the printer209
Downloaded From ManualsPrinter.com Manuals 

8Push the photoconductor as far as it will go.
The photoconductor clicks into place when correctly installed.
9Close Side Door A.
Maintaining the printer210
Downloaded From ManualsPrinter.com Manuals