Lexmark X463de User Manual

12If a printer hard disk was previously installed, then attach the printer hard disk to the ISP. For more information,
see “Installing a printer hard disk” on page 42.
13Release the latch, and then close the system board door by lowering the scanner.
14Push in on the screws while rotating them clockwise a quarter turn to lock the system board into place.
Warning—Potential Damage: Make sure the system board is locked to prevent possible damage to the printer if it is
moved. Additional printer setup41...

Installing a printer hard disk
The optional printer hard disk can be installed with or without a Lexmark Internal Solutions Port (ISP).
Note: This task requires a #2 Phillips screwdriver and a flathead screwdriver.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the...

To install a printer hard disk onto the ISP:
aUsing a flathead screwdriver to loosen the screws, remove the thumbscrews that attach the printer hard disk
mounting bracket to the printer hard disk, and then remove the bracket.
bAlign the standoffs of the printer hard disk with the holes in the ISP, and then press downward on the printer
hard disk until the standoffs have seated into place.
cInsert the plug of the printer hard disk interface cable into the receptacle of the ISP.
Note: The plugs and...

To install a printer hard disk directly onto the system board:
aAlign the standoffs of the printer hard disk with the holes in the system board, and then press downward on
the printer hard disk until the standoffs have seated into place.
Additional printer setup44
Downloaded From ManualsPrinter.com Manuals 

bAttach the two provided screws to secure the printer hard disk mounting bracket.
cInsert the plug of the printer hard disk interface cable into the receptacle of the system board.
Note: The plugs and receptacles are color coded.
4Release the latch, and then close the system board door by lowering the scanner. Additional printer setup45
Downloaded From ManualsPrinter.com Manuals 

5Push in on the screws while rotating them clockwise a quarter turn to lock the system board into place.
Warning—Potential Damage:  Make sure the system board is locked to prevent possible damage to the printer if it is
moved.
Installing a fax card
Note: This task requires a #2 Phillips screwdriver and a flathead screwdriver.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and...

3Remove the metal cover from the fax card opening.
1
2
4Insert the fax card, and then tighten the two screws to secure the fax card mounting bracket.
Additional printer setup47
Downloaded From ManualsPrinter.com Manuals 

5Insert the plug of the fax card interface cable into the receptacle of the system board.
6Release the latch, and then close the system board door by lowering the scanner.
7Push in on the screws while rotating them clockwise a quarter turn to lock the system board into place.
Warning—Potential Damage:  Make sure the system board is locked to prevent possible damage to the printer if it is
moved. Additional printer setup48
Downloaded From ManualsPrinter.com Manuals 

Installing hardware options
Installing a 250‑ or 550‑sheet drawer
The printer supports one optional drawer; you can install a 250‑ or 550‑sheet drawer.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well,
and unplug any cables going into...

6Align the printer with the drawer, and then lower the printer into place.
Attaching cables
Connect the printer to the computer using a USB cable, or to the network using an Ethernet cable.
Be sure to match the following:
The USB symbol on the cable with the USB symbol on the printer
The appropriate Ethernet cable to the Ethernet port Additional printer setup50
Downloaded From ManualsPrinter.com Manuals