Lexmark X203n User Manual

							Waiting
The printer has received data to print, but is waiting for an End‑of‑Job command, a Form Feed command, or additional
data.
Press  to print the contents of the buffer.
Cancel the current print job.
31.yy Replace defective or missing cartridge
The toner cartridge is either missing or not functioning properly.
Try one or more of the following:
Remove the toner cartridge, and then reinstall it.
Remove the toner cartridge, and then install a new one.
30 Invalid refill, change toner cartridge
The printer has detected an invalid, refilled toner cartridge. Remove the toner cartridge, and then install a new one.
32 Replace unsupported cartridge
Remove the toner cartridge, and then install a supported one.
34 Short paper
The printer paper size setting did not match the length of the paper that entered the printer.
Try one or more of the following:
Press  to clear the message and continue printing.
Press , and then press  to cancel printing.
Make sure the paper size setting matches the size of the paper in the tray.
37 Insufficient memory to collate job
Try one or more of the following:
Press the arrow buttons until Continue appears, and then press  to print the portion of the job already stored
and begin collating the rest of the print job.
Cancel the current print job.
38 Memory full
Try one or more of the following:
Press the arrow buttons until Continue appears, and then press  to clear the message.
Cancel the current print job.
Troubleshooting
131
Downloaded From ManualsPrinter.com Manuals 
						

							39 Complex page, some data may not have printed
Try one or more of the following:
Press the arrow buttons until Continue appears, and then press  to clear the message and continue printing.
Cancel the current print job.
54 Standard network software error
Try one or more of the following:
Press the arrow buttons until Continue appears, and then press  to continue printing.
Turn the printer off and then back on to reset the printer.
Upgrade (flash) the network firmware in the printer or print server.
54 Network  software error
Try one or more of the following:
Press the arrow buttons until Continue appears, and then press  to continue printing.
Turn the printer off and then back on to reset the printer.
Upgrade (flash) the network firmware in the printer or print server.
56 Standard USB port disabled
Try one or more of the following:
The printer discards any data received through the USB port. Press  to clear the message and continue printing.
Make sure the USB Buffer menu item is not set to Disabled.
84 PC Kit life warning
The photoconductor kit is near exhaustion.
Try one or more of the following:
Replace the photoconductor kit.
Press  to clear the message and continue printing.
84 Replace PC Kit
The photoconductor kit is exhausted. Install a new photoconductor kit.
88.yy Cartridge is low
Replace the toner cartridge, and then press  to clear the message and continue printing.
Troubleshooting
132
Downloaded From ManualsPrinter.com Manuals 
						

							200–250 paper jam
1Clear the paper path. For more information, see “Clearing jams” on page 136.
2After clearing the paper path, press  to resume printing.
290–294 paper jams
1Remove all original documents from the ADF.
2Open the ADF cover.
3Unlock the separator roll.
4Remove the separator roll.
Troubleshooting
133
Downloaded From ManualsPrinter.com Manuals 
						

							5Remove the jammed paper.
6Reinstall the separator roll.
7Lock the separator roll.
8Close the ADF cover.
Troubleshooting
134
Downloaded From ManualsPrinter.com Manuals 
						

							9Open the scanner cover, and then remove any jammed pages.
3DEF6MNO9WXYZ#
2ABC5JKL8TUV0
1@!.GHI4P
Q
R
S7*
10Press .
840.01 Scanner Disabled
This message indicates that the scanner has been disabled by the system support person.
840.02 Scanner Auto Disabled
This message indicates that the printer identified a problem with the scanner and automatically disabled it.
1Remove all pages from the ADF.
2Turn the printer off.
3Wait 15 seconds, and then turn the printer on.
4Place the document in the ADF, and then adjust the paper guides.
5Press .
Note: If turning the printer off and then on again does not clear the message, then contact your system support
person.
Troubleshooting
135
Downloaded From ManualsPrinter.com Manuals 
						

							Clearing jams
By carefully selecting paper and loading it properly, you can avoid most jams. If jams do occur, follow the steps outlined
in this chapter.
To clear a jam message and resume printing, clear the entire paper path, and then press 
. If Jam Recovery is set to
On, the printer prints a new copy of the page that jammed. If Jam Recovery is set to Auto, the printer may or may not
print a new copy of the page that jammed.
Avoiding jams
The following hints can help you avoid jams:
Paper tray recommendations

Make sure the paper lies flat in the paper tray.
Do not remove the paper tray while the printer is printing.
Do not load the paper tray while the printer is printing. Load it prior to printing, or wait for a prompt to load it.
Do not load too much paper. Make sure the stack height does not exceed the indicated maximum height.
Make sure the guides in the paper tray or the manual feeder are properly positioned and are not pressing too tightly
against the paper or envelopes.
Push the paper tray in firmly after loading paper.
Paper recommendations

Use only recommended paper or specialty media.
Do not load wrinkled, creased, damp, bent, or curled paper.
Flex, fan, and straighten paper before loading it.
Do not use paper that has been cut or trimmed by hand.
Do not mix paper sizes, weights, or types in the same stack.
Make sure all sizes and types are set correctly in the printer control panel menus.
Store paper per the manufacturers recommendations.
Troubleshooting
136
Downloaded From ManualsPrinter.com Manuals 
						

							200–201 paper jam
200 paper jam
1
Remove the tray from the printer.
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4P
Q
R
S7*
2Remove the jam if you see it here.
3DEF6MNO9WXYZ#
2ABC5JKL8TUV0
1@!.GHI4P
Q
R
S7*
3If you do not see it, see “201 paper jam” on page 138.
Troubleshooting
137
Downloaded From ManualsPrinter.com Manuals 
						

							201 paper jam
1
Open the front door, and then remove the photoconductor kit and toner cartridge.
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4PQRS7*
2Lift the flap at the front of the printer, and remove any jammed sheets.
3Align and insert the photoconductor kit and toner cartridge.
4Close the front door.
5Insert the tray.
6Press .
Troubleshooting
138
Downloaded From ManualsPrinter.com Manuals 
						

							202 paper jam
CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching.
1Open the front door, and then remove the photoconductor kit and toner cartridge.
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4PQRS7*
2Lift the flap at the front of the printer, and then remove any jammed sheets.
Troubleshooting
139
Downloaded From ManualsPrinter.com Manuals 
						

							3Open the rear door.
4Remove the jam.
5Close the rear door.
6Align and insert the photoconductor kit and toner cartridge.
7Close the front door.
8Press .
Troubleshooting
140
Downloaded From ManualsPrinter.com Manuals