Lexmark T652dn User Manual

							Paper types and weights supported by the printer
The printer engine supports 60–176 g/m2 (16–47 lb) paper weights. The duplex unit supports 63–170 g/m2 (17–45 lb)
paper weights.
Paper type250‑ or 550‑sheet
trays (standard or
optional)Optional 2000‑sheet
trayMultipurpose feederDuplex unit
Paper
Plain
Bond
Colored
Custom
Letterhead
Light
Heavy
Preprinted
Rough/Cotton
Recycled
Card stock
Envelopes X XX
Labels 
1
Paper
Vinyl
Transparencies
1 Printing labels requires a special label fuser cleaner which is included with the special cartridge required for label
applications.
Paper types and weights supported by the output bins
Use this table to determine the possible output destinations of print jobs which use supported paper types and weights.
The paper capacity of each output bin is listed in parentheses. Paper capacity estimations are calculated based on
75 g/m
2 (20 lb) paper.
The finisher supports 60–176 g/m
2 (16–47 lb) paper weights. Paper and specialty media guidelines 71
Downloaded From ManualsPrinter.com Manuals 
						

							Paper typeStandard exit bin
(350 or 550 sheets)Optional hardware
Output Expander (550
sheets) or High
Capacity Output
Stacker (1850 sheets)5‑Bin Mailbox
(500 sheets)
1
StapleSmart II
Finisher
(500 sheets)
2
Paper
Plain
Bond
Colored
Custom
Letterhead
Light
Heavy
Preprinted
Rough/Cotton
Recycled
Card stockXX
Envelopes
XX
Labels 
3
Paper
Vinyl
XX
Transparencies
XX
1 Supports 60‑90 g/m2 (16‑24 lb) paper weights.
2 Maximum of 50 sheets of 75 g/m2 (20 lb) paper per stapled packet. Results may vary with heavier paper.
3 Printing labels requires a special label fuser cleaner which is included with the special cartridge required for label
applications.
Paper and specialty media guidelines 72
Downloaded From ManualsPrinter.com Manuals 
						

							Printing
This chapter covers printing, printer reports, and job cancelation. Selection and handling of paper and specialty media
can affect how reliably documents print. For more information, see “Avoiding jams” on page 82 and “Storing paper”
on page 69.
Printing a document
1From the printer control panel Paper menu, set the Paper Type and Paper Size to match the loaded paper.
2Send the print job:
For Windows users
aWith a document open, click File > Print.
bClick Properties, Preferences, Options, or Setup, and then adjust the settings as needed.
Note: To print on a specific size or type of paper, adjust the paper size or type settings to match the loaded
paper, or select the appropriate tray or feeder.
cClick OK, and then click Print.
For Macintosh users
aCustomize the settings as needed in the Page Setup dialog:
1With a document open, choose File > Page Setup.
2Choose a paper size or create a custom size to match the loaded paper.
3Click OK.
bCustomize the settings as needed in the Print dialog:
1With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2From the Print dialog and pop‑up menus, adjust the settings as needed.
Note: To print on a specific paper type, adjust the paper type setting to match the loaded paper, or
select the appropriate tray or feeder.
3Click Print.
Printing on specialty media
Tips on using letterhead
Use letterhead designed specifically for laser printers.
Print samples on the letterhead being considered for use before buying large quantities.
Before loading letterhead, fan the stack to prevent sheets from sticking together.
Page orientation is important when printing on letterhead. For information on how to load letterhead, see:
–“Loading the standard or optional 250‑sheet or 550‑sheet tray” on page 52
–“Loading the 2000‑sheet tray” on page 56 Printing73
Downloaded From ManualsPrinter.com Manuals 
						

							–“Loading the multipurpose feeder” on page 59
Tips on using transparencies
Print samples on the transparencies being considered for use before buying large quantities.
When printing on transparencies:
Feed transparencies from a 250‑sheet tray, a 550‑sheet tray, or the multipurpose feeder.
Use transparencies designed specifically for laser printers. Check with the manufacturer or vendor to ensure
transparencies are able to withstand temperatures up to 230°C (446°F) without melting, discoloring, offsetting, or
releasing hazardous emissions.
Use transparencies that are 138–146 g/m2 (37–39 lb. bond) in weight.
To prevent print quality problems, avoid getting fingerprints on the transparencies.
Before loading transparencies, fan the stack to prevent sheets from sticking together.
We recommend Lexmark part number 12A5010 for A4‑size transparencies and Lexmark part number 70X7240 for
letter‑size transparencies.
Tips on using envelopes
Print samples on the envelopes being considered for use before buying large quantities.
When printing on envelopes:
Feed envelopes from the multipurpose feeder or the optional envelope feeder.
Set the Paper Type to Envelope, and select the envelope size.
Use envelopes designed specifically for laser printers. Check with the manufacturer or vendor to ensure the
envelopes can withstand temperatures up to 230°C (446°F) without sealing, wrinkling, curling excessively, or
releasing hazardous emissions.
For the best performance, use envelopes made from 90 g/m2 (24 lb bond) paper. Use up to 105 g/m2 (28 lb bond)
weight for envelopes as long as the cotton content is 25% or less. All‑cotton envelopes must not exceed 90 g/m
2
(24 lb bond) weight.
Use only new envelopes.
To optimize performance and minimize jams, do not use envelopes that:
–Have excessive curl or twist
–Are stuck together or damaged in any way
–Have windows, holes, perforations, cutouts, or embossing
–Have metal clasps, string ties, or folding bars
–Have an interlocking design
–Have postage stamps attached
–Have any exposed adhesive when the flap is in the sealed or closed position
–Have bent corners
–Have rough, cockle, or laid finishes
Adjust the width guide to fit the width of the envelopes.
Note: A combination of high humidity (over 60%) and the high printing temperature may wrinkle or seal envelopes. Printing74
Downloaded From ManualsPrinter.com Manuals 
						

							Tips on using labels
Print samples on the labels being considered for use before buying large quantities.
Notes:
Paper, dual‑web paper, polyester, and vinyl labels are supported.
When using the duplex unit, specially‑designed, integrated, and dual‑web paper labels are supported.
Printing labels requires a special label fuser cleaner which is included with the special cartridge required for
label applications. For more information, see “Ordering supplies” on page 169.
For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on
the Lexmark Web site at www.lexmark.com/publications.
When printing on labels:
Feed labels from a 250‑sheet tray, a 550‑sheet tray, or the multipurpose feeder.
Use labels designed specifically for laser printers. Check with the manufacturer or vendor to verify that:
–The labels can withstand temperatures up to 230°C (446°F) without sealing, excessive curling, wrinkling, or
releasing hazardous emissions.
–Label adhesives, face sheet (printable stock), and topcoats can withstand up to 25 psi (172 kPa) pressure without
delaminating, oozing around the edges, or releasing hazardous fumes.
Do not use labels with slick backing material.
Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets
also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge warranties.
Do not use labels with exposed adhesive.
Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die‑cuts of the label.
Be sure adhesive backing does not reach to the sheet edge. Zone coating of the adhesive at least 1 mm (0.04 in.)
away from edges is recommended. Adhesive material contaminates the printer and could void the warranty.
If zone coating of the adhesive is not possible, remove a 1.6‑mm (0.06‑in.) strip on the leading and driver edge, and
use a non‑oozing adhesive.
Portrait orientation works best, especially when printing bar codes.
Tips on using card stock
Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness,
and texture, can significantly impact print quality. Print samples on the card stock being considered for use before
buying large quantities.
When printing on card stock:
Feed card stock from a 250‑sheet tray, a 550‑sheet tray, or the multipurpose feeder.
Make sure the Paper Type is Card Stock.
Select the appropriate Paper Texture setting.
Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or
other paper handling problems.
Check with the manufacturer or vendor to ensure the card stock can withstand temperatures up to 230°C (446°F)
without releasing hazardous emissions. Printing75
Downloaded From ManualsPrinter.com Manuals 
						

							Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting
introduces semi‑liquid and volatile components into the printer.
Use grain short card stock when possible.
Printing confidential and other held jobs
Holding jobs in the printer
When sending a job to the printer, you can specify that you want the printer to hold the job in memory until you start
the job from the printer control panel. All print jobs that can be initiated by the user at the printer are called held jobs.
Note: Confidential, Verify, Reserve, and Repeat print jobs may be deleted if the printer requires extra memory to
process additional held jobs.
Job typeDescription
Confidential When you send a Confidential print job to the printer, you must create a PIN from
the computer. The PIN must be four digits using the numbers 0–9. The job is held
in printer memory until you enter the PIN from the printer control panel and
choose to print or delete the job.
Verify When you send a Verify print job, the printer prints one copy and holds the
remaining copies in printer memory. Verify lets you examine the first copy to see
if it is satisfactory before printing the remaining copies. Once all copies are printed,
the job is automatically deleted from printer memory.
Reserve When you send a Reserve print job, the printer does not print the job immediately.
It stores the job in memory so you can print the job later. The job is held in memory
until you delete it from the Held Jobs menu.
Repeat When you send a Repeat print job, the printer prints all requested copies of the
job and stores the job in memory so you can print additional copies later. You can
print additional copies as long as the job remains stored in memory.
Other types of held jobs include:
Profiles from various sources including Lexmark Document Solutions Suite (LDSS)
Forms from a kiosk
Bookmarks
Jobs not printed, which are called parked jobs
Printing confidential and other held jobs
Note: Confidential and Verify print jobs are automatically deleted from memory after they print. Repeat and Reserve
jobs continue to be held in the printer until you choose to delete them.
For Windows Users
1
With a document open, click File > Print.
2Click Properties, Preferences, Options, or Setup.
3Click Other Options, and then click Print and Hold. Printing76
Downloaded From ManualsPrinter.com Manuals 
						

							4Select your job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential job,
also enter a four‑digit PIN.
5Click OK or Print, and then go to the printer to release the job.
6From the printer control panel, press the arrow buttons until Held jobs appears, and then press .
7Press the arrow buttons until  appears next to your user name, and then press .
8Press the arrow buttons until  appears next to the job type or job name, and then press .
If you selected a job name, proceed to step 11 on page 77.
9After selecting your job type, use the keypad to enter your PIN.
If you enter an invalid PIN, the Invalid PIN screen appears.
To re‑enter the PIN, make sure Try again appears, and then press .
To cancel the PIN, press the arrow buttons until Cancel appears, and then press .
10Press the arrow buttons until  appears next to the job you want to print, and then press .
11Press the arrow buttons until  appears next to the number of copies you want to print, and then press .
Note: Use the keypad to enter a number if necessary.
For Macintosh users
1
With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3Select your job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential job,
also enter a four‑digit PIN.
4Click OK or Print, and then go to the printer to release the job.
5From the printer control panel, press the arrow buttons until Held jobs appears, and then press .
6Press the arrow buttons until  appears next to your user name, and then press .
7Press the arrow buttons until  appears next to the job type or job name, and then press .
If you selected a job name, proceed to step 10 on page 78.
8After selecting your job type, use the keypad to enter your PIN.
If you enter an invalid PIN, the Invalid PIN screen appears.
To re‑enter the PIN, make sure Try again appears, and then press .
To cancel the PIN, press the arrow buttons until Cancel appears, and then press . Printing77
Downloaded From ManualsPrinter.com Manuals 
						

							9Press the arrow buttons until  appears next to the job you want to print, and then press .
10Press the arrow buttons until  appears next to the number of copies you want to print, and then press .
Note: Use the keypad to enter a number if necessary.
Printing from a flash drive
A USB port is located on the printer control panel. Insert a flash drive to print supported file types. Supported file types
include: .pdf, .gif, .jpeg, .jpg, .bmp, .png, .tiff, .tif, .pcx, .xps, and .dcx.
Many flash drives are tested and approved for use with the printer. For more information, visit the Lexmark Web site
at www.lexmark.com.
Notes:
High‑speed flash drives must support the full‑speed USB standard. Flash drives supporting only USB low‑speed
capabilities are not supported.
Flash drives must support the FAT (File Allocation Tables) system. Flash drives formatted with NTFS (New
Technology File System) or any other file system are not supported.
Before printing an encrypted .pdf file, enter the file password from the printer control panel.
You cannot print files for which you do not have printing permissions.
To print from a flash drive:
1Make sure the printer is on and Ready appears.
2Insert a flash drive into the front USB port.
Notes:
If you insert the flash drive when the printer requires attention, such as when a jam has occurred, then the
printer ignores it.
If you insert the flash drive while the printer is printing other jobs, then Printer Busy appears. After the
other jobs are processed, you may need to view the held jobs list to print documents from the flash drive. Printing78
Downloaded From ManualsPrinter.com Manuals 
						

							3Press the down arrow button until  appears next to the document you want to print, and then press .
Note: Folders found on the flash drive appear as folders. File names are appended by the extension type (for
example, .jpg).
4Press  to print one copy, or enter the number of copies using the keypad, and then press  to initiate the print
job.
Note: Do not remove the flash drive from the printer until the document has finished printing.
If you leave the flash drive in the printer after leaving the initial USB menu screen, you can still print .pdf files from
the flash drive as held jobs.
Printing information pages
Printing a font sample list
To print samples of the fonts currently available for your printer:
1Make sure the printer is on and Ready appears.
2From the printer control panel, press .
3Press the arrow buttons until Reports appears, and then press .
4Press the arrow buttons until Print Fonts appears, and then press .
5Press the arrow buttons until  appears next to PCL Fonts, PostScript Fonts, or PPDS Fonts, and
then press 
.
Printing a directory list
A directory list shows the resources stored in flash memory or on the hard disk.
1Make sure the printer is on and Ready appears.
2From the printer control panel, press .
3Press the arrow buttons until  Reports appears, and then press .
4Press the arrow buttons until  Print Directory appears, and then press .
Printing the print quality test pages
Print the print quality test pages to isolate print quality problems.
1Turn the printer off.
2Hold down  and  while turning the printer on.
3Release the buttons when the clock appears, and wait for CONFIG MENU to appear. Printing79
Downloaded From ManualsPrinter.com Manuals 
						

							4Press the arrow buttons until Prt Quality Pgs appears, and then press .
The print quality test pages print.
5Press the arrow buttons until Exit Config Menu appears, and then press .
Resetting the Printer appears briefly, followed by a clock, and then Ready appears.
Canceling a print job
Canceling a print job from the printer control panel
If the job is formatting or already printing, and Cancel a job appears on the first line of the display:
1Press the arrow buttons until Cancel appears.
A list of jobs appears.
2Press the arrow buttons until  appears next to the job you want to cancel, and then press .
Note: Once a print job is sent, to easily cancel a job, press 
. The Stopped screen appears. Press the arrow
buttons until 
Cancel a job appears, and then press .
Canceling a print job from the computer
To cancel a print job, do one of the following:
For Windows users
1Click , or click Start and then click Run.
2In the Start Search or Run box, type control printers.
3Press Enter, or click OK.
The printer folder opens.
4Double‑click the printer icon.
5Select the job to cancel.
6From the keyboard, press Delete.
From the Windows taskbar:
When you send a job to print, a small printer icon appears in the right corner of the taskbar.
1Double‑click the printer icon.
A list of print jobs appears in the printer window.
2Select a job to cancel.
3From the keyboard, press Delete. Printing80
Downloaded From ManualsPrinter.com Manuals