Lexmark T652dn User Manual

							Menu itemDescription
Std Network Setup
Reports or Network Reports
Network Card
TCP/IP
IPv6
AppleTalk
NetWare
LexLink
Net  Setup
Reports or Network Reports
Network Card
TCP/IP
IPv6
Wireless
AppleTalk
NetWare
LexLinkFor descriptions and settings of the network setup menus, see the following:
“Network Reports menu” on page 111
“Network Card menu” on page 111
“TCP/IP menu” on page 112
“IPv6 menu” on page 113
“Wireless menu” on page 113
“AppleTalk menu” on page 114
“NetWare menu” on page 114
“LexLink menu” on page 115
Note: The Wireless menu appears only when the printer is connected to a wireless
network.
Network Reports menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > Reports or Network
Reports
Menu itemDescription
Print Setup Page
Print NetWare Setup
PagePrints a report containing information about the current network setup
Notes:
The Setup Page contains information about the network printer settings, such as the
TCP/IP address.
The NetWare Setup Page menu item appears only on models that support NetWare and
shows information about NetWare settings.
Network Card menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > Network Card
Menu itemDescription
View Card Status
Connected
DisconnectedLets you view the connection status of the Network Card
View Card SpeedLets you view the speed of a currently active network card
Understanding printer menus111
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Network Address
UAA
LAALets you view the network addresses
Job Timeout
0‑225 secondsSets the amount of time in seconds that a network print job can take before it
is canceled
Notes:
90 seconds is the factory default setting.
A setting value of 0 disables the timeout.
If a value of 1–9 is selected, then the setting is saved as 10.
Banner Page
Off
OnAllows the printer to print a banner page
Note: Off is the factory default setting.
TCP/IP menu
Use the following menu items to view or set the TCP/IP information.
Note: This menu is available only for network models or printers attached to print servers.
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > TCP/IP
Menu itemDescription
Activate
On
OffActivates TCP/IP
Note: On is the factory default setting.
View HostnameLets you view the current TCP/IP hostname
Note: This can be changed only from the Embedded Web Server.
IP AddressLets you view or change the current TCP/IP Address
Note: Manually setting the IP address sets the Enable DHCP and Enable Auto IP
settings to Off. It also sets Enable BOOTP and Enable RARP to Off on systems that
support BOOTP and RARP.
NetmaskLets you view or change the current TCP/IP Netmask
GatewayLets you view or change the current TCP/IP Gateway
Enable DHCP
On
OffSpecifies the DHCP address and parameter assignment setting
Enable RARP
On
OffSpecifies the RARP address assignment setting
Note: On is the factory default setting.
Understanding printer menus112
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Enable BOOTP
On
OffSpecifies the BOOTP address assignment setting
Note: On is the factory default setting.
AutoIP
Yes
NoSpecifies the Zero Configuration Networking setting
Note: Yes is the factory default setting.
Enable FTP/TFTP
Yes
NoEnables the built-in FTP server, which allows you to send files to the printer using the
File Transfer Protocol.
Note: Yes is the factory default setting.
Enable HTTP Server
Yes
NoEnables the built-in web server (Embedded Web Server). When enabled, the printer
can be monitored and managed remotely using a web browser.
Note: Yes is the factory default setting.
WINS Server AddressLets you view or change the current WINS Server Address
DNS Server AddressLets you view or change the current DNS Server Address
IPv6 menu
Use the following menu items to view or set the Internet Protocol version 6 (IPv6) information.
Note: This menu is available only for network models or printers attached to print servers.
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > IPv6
Menu itemDescription
Enable IPv6
On
OffEnables IPv6 in the printer
Note: On is the factory default setting.
Auto Configuration
On
OffSpecifies whether the network adapter accepts the automatic IPv6
address configuration entries provided by a router
Note: On is the factory default setting.
View Hostname
View Address
View Router AddressLets you view the current setting
Note: These settings can be changed only from the Embedded Web
Server.
Enable DHCPv6
On
OffEnables DHCPv6 in the printer
Note: On is the factory default setting.
Wireless menu
Use the following menu items to view or configure the wireless internal print server settings.
Note: This menu is available only for models connected to a wireless network. Understanding printer menus113
Downloaded From ManualsPrinter.com Manuals 
						

							This menu is available from the Network/Ports menu:
Network/Ports > Network  > Net  Setup > Wireless
Menu itemDescription
Network Mode
Infrastructure
Ad hocSpecifies the network mode
Notes:
Infrastructure mode lets the printer access a network using an
access point.
Ad hoc is the factory default setting. Ad hoc mode configures the
printer for wireless networking directly between it and a computer.
Compatibility
802.11n
802.11b/g
802.11b/g/nSpecifies the wireless standard for the wireless network
Choose Network
Lets you select an available network for the printer to use
View Signal QualityLets you view the quality of the wireless connection
View Security ModeLets you view the encryption method for the wireless connection.
“Disabled” indicates that the wireless network is not encrypted.
AppleTalk menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > AppleTalk
Menu itemDescription
Activate
On
OffActivates AppleTalk support
Note: On is the factory default setting.
View NameShows the assigned AppleTalk name
Note: The name can be changed only from the Embedded Web Server.
View AddressShows the assigned AppleTalk address
Note: The address can be changed only from the Embedded Web Server.
Set Zone
Provides a list of AppleTalk zones available on the network
Note: The default setting is the default zone for the network. If no default
zone exists, the zone marked with an * is the default setting.
NetWare menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > NetWare Understanding printer menus114
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Activate
Yes
NoActivates NetWare support
Note: No is the factory default setting.
View Login NameLets you view the assigned NetWare login name
Note: This can be changed only from the Embedded Web Server.
Print ModeLets you view the assigned NetWare print mode
Note: This can be changed only from the Embedded Web Server.
Network NumberLets you view the assigned NetWare network number
Note: This can be changed only from the Embedded Web Server.
Select SAP Frames
Ethernet 802.2
Ethernet 802.3
Ethernet Type II
Ethernet SNAPEnables the Ethernet frame type setting
Note: On is the factory default setting for all menu items.
Packet Burst
Yes
NoReduces network traffic by allowing the transfer and acknowledgement of
multiple data packets to and from the NetWare server
Note: Yes is the factory default setting.
NSQ/GSQ Mode
Yes
NoSpecifies the NSQ/GSQ Mode setting
Note: Yes is the factory default setting.
LexLink menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > LexLink menu
Menu itemDescription
Activate
On
OffActivates LexLink support
Note: Off is the factory default setting.
View NicknameLets you view the assigned LexLink nickname
Note: The LexLink nickname can be changed only from the Embedded Web
Server.
Understanding printer menus115
Downloaded From ManualsPrinter.com Manuals 
						

							Standard USB menu
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if the PS
SmartSwitch setting is On. It uses the default printer language specified in the
Setup menu if the PS SmartSwitch setting is Off.
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if the PCL
SmartSwitch setting is On. It uses the default printer language specified in the
Setup menu if the PCL SmartSwitch setting is Off.
NPA Mode
On
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
USB Buffer
Disabled
Auto
3K to Sets the size of the USB input buffer
Notes:
Auto is the factory default setting.
The Disabled setting turns off job buffering. Any jobs already buffered on the
disk are printed before normal processing is resumed.
The USB buffer size value can be changed in 1‑K increments.
The maximum size allowed depends on the amount of memory in the printer,
the size of the other link buffers, and whether the Resource Save setting is On
or Off.
To increase the maximum size range for the USB Buffer, disable or reduce the
size of the parallel, serial, and network buffers.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Understanding printer menus116
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Job Buffering
Off
On
AutoTemporarily stores jobs on the printer hard disk before printing
Notes:
Off is the factory default setting.
The On setting buffers jobs on the printer hard disk.
The Auto setting buffers print jobs only if the printer is busy processing data
from another input port.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Mac Binary PS
On
Off
AutoSets the printer to process Macintosh binary PostScript print jobs
Notes:
Auto is the factory default setting.
The Off setting filters print jobs using the standard protocol.
The On setting processes raw binary PostScript print jobs.
USB With ENA
ENA Address
ENA Netmask
ENA GatewaySets the network address, netmask, or gateway information for an external print
server that is attached to the printer using a USB cable.
Note: This menu item is available only if the printer is attached to an external print
server through the USB port.
Parallel  menu
This menu appears only if an optional parallel card is installed.
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a parallel port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if PS
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PS SmartSwitch is set to Off.
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job received
through a parallel port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if PCL
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PCL SmartSwitch is set to Off.
Understanding printer menus117
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
NPA Mode
On
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Parallel Buffer
Disabled
Auto
3K to Sets the size of the parallel input buffer
Notes:
Auto is the factory default setting.
The Disabled setting turns off job buffering. Any jobs already buffered on the
disk are printed before normal processing is resumed.
The parallel buffer size setting can be changed in 1K increments.
The maximum size allowed depends on the amount of memory in the printer,
the size of the other link buffers, and whether Resource Save is set to On or
Off.
To increase the maximum size range for the Parallel Buffer, disable or reduce
the size of the USB, serial, and network buffers.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Job Buffering
Off
On
AutoTemporarily stores jobs on the printer hard disk before printing
Notes:
Off is the factory default setting.
The Off setting does not buffer print jobs to the printer hard disk.
The On setting buffers jobs on the printer hard disk.
The Auto setting buffers print jobs only if the printer is busy processing data
from another input port.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Advanced Status
On
OffEnables bidirectional communication through the parallel port
Notes:
On is the factory default setting.
The Off setting disables parallel port negotiation.
Protocol
Standard
FastbytesSpecifies the parallel port protocol
Notes:
Fastbytes is the factory default setting. It provides compatibility with most
existing parallel ports and is the recommended setting.
The Standard setting tries to resolve parallel port communication problems.
Understanding printer menus118
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Honor Init
On
OffDetermines whether or not the printer honors printer hardware initialization
requests from the computer
Notes:
Off is the factory default setting.
The computer requests initialization by activating the Init signal from the
parallel port. Many personal computers activate the Init signal each time the
computer is turned on.
Parallel Mode 2
On
OffDetermines whether the parallel port data is sampled on the leading or trailing edge
of strobe
Notes:
On is the factory default setting.
This menu appears only if a standard or optional parallel port is available.
Mac Binary PS
On
Off
AutoSets the printer to process Macintosh binary PostScript print jobs
Notes:
Auto is the factory default setting.
The Off setting filters print jobs using the standard protocol.
The On setting processes raw binary PostScript print jobs.
Parallel With ENA
ENA Address
ENA Netmask
ENA GatewaySets the network address, netmask, or gateway information for an external print
server that is attached to the printer using a parallel cable.
Note: This menu item is available only if the printer is attached to an external print
server through a parallel port.
Serial  menu
This menu appears only if an optional serial card is installed.
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a serial port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if PS
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PS SmartSwitch is set to Off.
Understanding printer menus119
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job received
through a serial port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if PCL
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PCL SmartSwitch is set to Off.
NPA Mode
On
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
When the On setting is used, the printer performs NPA processing. If the data
is not in NPA format, it is rejected as bad data.
When the Off setting is used, the printer does not perform NPA processing.
When the Auto setting is used, the printer examines data, determines the
format, and then processes it appropriately.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Serial Buffer
Disabled
Auto
3K to Sets the size of the serial input buffer
Notes:
Auto is the factory default setting.
The Disabled setting turns off job buffering. Any jobs already buffered on the
disk are printed before normal processing is resumed.
The serial buffer size setting can be changed in 1‑K increments.
The maximum size allowed depends on the amount of memory in the printer,
the size of the other link buffers, and whether Resource Save is set to On or
Off.
To increase the maximum size range for the Serial Buffer, disable or reduce
the size of the parallel, USB, and network buffers.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Job Buffering
Off
On
AutoTemporarily stores jobs on the printer hard disk before printing
Notes:
Off is the factory default setting.
The Off setting does not buffer print jobs to the hard disk.
The On setting buffers jobs on the printer hard disk.
The Auto setting buffers print jobs only if the printer is busy processing data
from another input port.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Understanding printer menus120
Downloaded From ManualsPrinter.com Manuals