Lexmark Optra S 1620 Manual

Diagnostic Information2-14
4059-XXX
Restoring Factory
DefaultsThe printer is restoring
factory defaults.No button actions are
possible while this
message is displayed.
Performing Self Tests The printer is running
the normal series of
start-up tests after it is
powered On. When the
tests are complete, the
printer returns to Ready.No button actions are
possible while this
message is displayed.
Not Ready
(Press Go)TheprinterisintheNot
Ready State, which
means it is not ready to
receive or process data.
This...

2-154059 Service Manual
4059-XXX
Programming Disk
(Do Not Power Off)The disk is being
programmed, which
means fonts or macros
arebeingwrittentodisk.No button actions are
possible while this
message is displayed.
Note:If information is
writtentoflash
memory and to disk at
thesametime,the
Program Flash
message is displayed.
Menus Disabled The printer menus have
been disabled. This
occurs when Menu> or

Diagnostic Information2-16
4059-XXX
User Error Messages
User Error Message Explanation
200 Paper Jam
Remove CartridgePaper is jammed at the printer Input Sensor.
Open the printer’s upper front door and remove
the print cartridge to access the paper jam area.
201 Paper Jam
Remove CartridgePaper is jammed between the printer’s input and
exit sensors. Open the printer’s upper front door
and remove the print cartridge to access the jam
area.
202 Paper Jam
Open Rear DoorPaper is jammed at the printer exit...

2-174059 Service Manual
4059-XXX
31 Defective Print
CartridgeError code 31 is displayed when the top front
cover is closed and a defective print cartridge is
detected. It may take the printer 10-20 seconds to
determine if the print cartridge is defective.
Depending on the setting of the Machine Class ID
the printer may be allowed to print pages during
this 10-20 second interval. If pages are allowed to
print, they are not reprinted once a good print
cartridge is inserted.
Note: This error indicates the...

Diagnostic Information2-18
4059-XXX
36 Resolution Reduced The resolution of the page has been reduced
from 600 dpi to 300 dpi in order to prevent a
Memory Full error. This message can only occur if
the Resolution Reduction setting is turned on.
Note: 1200 dpi pages are not resolution reduced.
If a 1200 dpi job runs out of memory, a Memory
Full error is displayed.
37 Insufficient Collation
MemoryThis message is displayed when the printer
memory used to store pages is too full to collate
the print job.
38...

2-194059 Service Manual
4059-XXX
56 Standard Serial
DisabledThis error is displayed when data is sent to the
printer across the standard serial port, but the
port has been disabled.
56 Parallel Port Disabled This error is displayed when data is sent to the
printer across the parallel port, but the parallel
port has been disabled. Once this message is
displayed, reporting of further errors is
suppressed until the menus are entered, or the
printer is reset.
58 Too Many Trays
AttachedThis error code is...

Diagnostic Information2-20
4059-XXX
User Line 2 Messages
If none of the conditions exist that are listed in the following table,
line 2 is blank. If any of the messages in the table are displayed the
following actions can be taken:
Press Menu> or 

2-214059 Service Manual
4059-XXX
.
User Message Explanation
Toner Low If the toner cartridge is low, then “Toner Low”
displays. The Toner Low condition clears
whenever the upper front door is opened, and
Toner Low displays again if the condition exists
after the upper front door is closed.
Tray X Missing If any of the input trays are missing, then “Tray X
Missing” displays (where X designates which Tray
(1 through 5) is missing. If multiple trays are
missing, they are prioritized in this order: Tray 1,...

Diagnostic Information2-22
4059-XXX
User Line 2 Link Messages
If the printer is locked on a particular link, the link indication displays.
If the printer is ready to process any link, none display. The link
messages are listed in the following table.
Check Device Connection Messages
The messages in the following table display when the printer looses
communications with one of the following devices.
User Message Explanation
Parallel Standard Parallel Port, if available.
Serial Standard Serial Port, if...

2-234059 Service Manual
4059-XXX
The messages in the following table can occur in two ways. The
specified device could have been removed from the printer, for
instance to clear a paper jam. Otherwise, the device can still be
attached to the printer, but is experiencing a communications
problem, not fully connected, or having a hardware failure.
•If the device is temporarily removed or not connected properly,
then reattach it. When the option is recognized, the printer
automatically clears the error and...