Lexmark Optra S 1250 Manual

Optional Drawers
Chapter
Optional Drawers255
Installing Options
Optional
Drawers
12
The following table gives information for the optional 250-sheet
drawer and optional 500-sheet drawer depending on which printer
model you have:
Note:A 2000-sheet drawer is available and may be substituted for
any one optional drawer.
Each optional drawer consists of a support unit and a paper tray.
Allsupportunitsandtraysareinstalledinthesamemanner.The
only physical difference between optional drawers is the depth.
Optra...

Optional Drawers256
Optional Drawers
Installing Options
Installing an Optional Drawer
If your printer is already set up, make sure the printer power is
Off (O). Unplug the power cord, and disconnect any cables
attached to the printer.
An optional drawer consists of a support unit and a paper tray.
1Remove the support unit from its packaging.Remove any
packing tape.
2Pull the paper tray out of the support unit.Remove any
packing material and tape from the paper tray.
Note:Options compatible with the Optra...

257Optional Drawers
Optional Drawers
Installing Options
3Grasp the support unit on each side at opposite corners
and move it to the location being used.
4Notice the following parts located on the top surface of
any optional support unit: the tab, the round hole, and
the four square holes.
At this point, attach another optional drawer or the printer. To
attach a drawer, continue with step 5 through step 7 on page 258.
To attach the printer, continue with step 8 on page 259.
Note:If you have a duplex...

Optional Drawers258
Optional Drawers
Installing Options
5Remove the support unit from its packaging.Remove any
packing tape.
6Pull the paper tray out of the support unit.Remove any
packing material and tape from the paper tray
7Grasp the support unit on each side at opposite corners
and lower it onto the top of the previous support unit.Be
sure the edges of both support units are aligned so that all
the parts (tab, round hole, four square holes) fit in the
matching holes and feet.
Note:The bottom surface...

259Optional Drawers
Optional Drawers
Installing Options
8Lift the printer by the hand grips or ask someone to help
you lift the printer.
The bottom surface of the printer has matching holes or feet
that accommodate the tab, round hole, and four square
holes.
CAUTION:
Make sure your fingers are not under the
printerwhenyousetitdown.
9Place the printer on top of the support unit.Be sure the
edges of the printer and the support unit are aligned so that
all the parts fit. The right side of the printer is...

Optional Drawers260
Optional Drawers
Installing Options
14Plug in the printer power cord.
15Turn the printer power On (|).
Note:Verify that the optional drawer is installed properly.
See “Verifying the Installation of Options” on
page 325.
16From the operator panel, set the PAPER TYPE menu
setting for each paper source.
Note:The 250-sheet input tray in the printer is Tray 1.
Trays for support units installed under the printer
are numbered Tray 2 down to Tray 5 depending on
the number of optional drawers...

Envelope Feeder Option
Chapter
Envelope Feeder Option261
Installing Options
Envelope
Feeder Option
13
The envelope feeder option attaches to the front of your printer
behind the lower front door. It can be removed when you are not
using it, making the printer more compact.
You may install the envelope feeder without turning the printer off
first, butdo notremove it when the printer is on. The message
Reattach Envelope Feederdisplays if you remove the envelope
feeder when the printer is on. When this...

Envelope Feeder Option262
Envelope Feeder Option
Installing Options
Installing the Envelope Feeder
Note:Options compatible with the Optra S 1855 are labeled with
a colored circle. If the option is not labeled with a colored
circle, do not install it on an Optra S 1855. See the table on
page 1 for the location of the label.
1Turn the printer power Off (O).
2Push the lower release latch on the front left side of the
printer to the right to release the door. 

263Envelope Feeder Option
Envelope Feeder Option
Installing Options
The door drops open and stops in place.
3Grasp the lower right corner of the envelope feeder
connector door and pull it up.The connector is exposed.
Envelope Feeder
Connector Door 

Envelope Feeder Option264
Envelope Feeder Option
Installing Options
4Align the tabs on the envelope feeder with the slots on
both sides of the printer and gently push the envelope
feeder into the opening until it snaps into place.The
envelope feeder tilts downward at a slight angle if it is
installed properly.
5Turn the printer power On (|).
Note:Verify that the envelope feeder is installed properly.
See “Verifying the Installation of Options” on
page 325.
Slots