Lexmark E120 User Manual

Overview of the Lexmark E120n operator panel
31
Using the operator panels
Invalid engine code 
Not ready 
Printing font list or menu settings page 
Light sequence:
Ready / Data—On
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Ready / Data—On
Load / Remove Paper—On
Error—On
Message:
The internal engine code has not been programmed, or the programmed code is not valid.
Solution:
Download valid engine code.
Light sequence:
Continue—On
Ready / Data—On...

Overview of the Lexmark E120n operator panel
32
Using the operator panels
Programming engine code or system code 
Restoring factory defaults
 
Cartridge region mismatch 
Light sequence:
Ready / Data—On
Error—On
Message:
New code is being programmed into the engine or firmware.
Solution:
Wait for message to clear. When printer has finished programming the code, it returns to ready.
Note:No buttons are active while this message is displayed.
Light sequence:
Continue—On
Ready / Data—On
Toner...

Overview of the Lexmark E120n operator panel
33
Using the operator panels
Change cartridge
Open door
Light sequence:
Toner Low/Replace PC Kit—On
Error—Blinking
Message:
Printer has detected a refilled Return Program toner cartridge has been installed.
Solution:
Remove current toner cartridge, and install a new toner cartridge.
Light sequence:
Error—On
Message:
Door is open.
Solution:
Close the open door.
Downloaded From ManualsPrinter.com Manuals 

Overview of the Lexmark E120n operator panel
34
Using the operator panels
Complex page
Missing cartridge / Defective cartridge detected 
Light sequence:
Continue—On
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Continue—On
Ready / Data—On
Error—On
Message:
The page may not print correctly because the print information on the page is too complex (that is, too large for the 
printer memory).
Solution:
Press to clear message and continue processing the...

Overview of the Lexmark E120n operator panel
35
Using the operator panels
ENA connection lost 
Light sequence:
Continue—On
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Continue—On
Paper Jam—Blinking
Error—On
Message:
During power-on cycle, the printer detected the connection to the external network adapter was lost.
Note:This error is only detected during power-on cycle.
Solution:
Press  to clear message.
Re-establish connection with the external...

Overview of the Lexmark E120n operator panel
36
Using the operator panels
Insufficient collation area 
Load media 
Light sequence:
Continue—On
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Continue—On
Toner Low/Replace PC Kit—On
Error—On
Message:
Printer memory does not have the free space necessary to collate print job. May occur due to one of the errors 
listed below:
Printer memory is full.
A page is too complex to print.
Memory is insufficient to...

Overview of the Lexmark E120n operator panel
37
Using the operator panels
Print side two of a duplex job 
Memory full 
Light sequence:
Continue—Blinking
Load / Remove Paper—On
Message:
Print the other side of current duplex print job.
Solution:
Insert print job into priority feeder using instructions in the driver pop-up menu to orient pages correctly, 
then press to resume printing.
Press to cancel print job.
Press and hold to reset printer.
Light sequence:
Continue—On
Error—On
Secondary light...

Overview of the Lexmark E120n operator panel
38
Using the operator panels
Network interface errors 
Host interface disabled 
Light sequence:
Continue—On
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Continue—On
Paper Jam—On
Error—On
Message:
Printer cannot establish communication with the network.
Solution:
Press to clear message and continue printing. (may not print correctly).
Press and hold to reset printer (may need to send the job again).
Light...

Overview of the Lexmark E120n operator panel
39
Using the operator panels
Jam at the input sensor
Jam between the input and exit sensors
Note:All jams show the same primary 
code. To determine the jam location,
view the secondary light sequence.
Light sequence:
Continue—On
Paper Jam—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Continue—On
Ready / Data—On
Paper Jam—On
Message:
A jam has occurred at the input sensor; it can be after the paper leaves the tray...

Overview of the Lexmark E120n operator panel
40
Using the operator panels
Jam at printer exit sensor
Jam in Tray 1 / priority feeder
Note:All jams show the same primary 
code. To determine the jam location,
view the secondary light sequence.
Light sequence:
Continue—On
Paper Jam—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Continue—On
Load / Remove Paper—On
Paper Jam—On
Message:
A jam has occurred at the printer exit sensor.
Solution:
See Clearing jams on...