Lexmark C935hdn User Manual

							Configured models
1Standard exit bin
2Control panel
3Standard 520‑sheet tray (Tray 1)
4–6The High capacity feeder holds 2520 sheets and includes:
•4—520‑sheet tray (Tray 2)
5—867‑sheet tray (Tray 3)
6—1133‑sheet tray (Tray 4)
7Multipurpose feeder
8Duplex unit
1Standard exit bin
2Control panel
Learning about the printer11
Downloaded From ManualsPrinter.com Manuals 
						

							3Standard 520‑sheet tray (Tray 1)
4‑6The Tandem tray module (TTM) holds 1560 sheets and includes:
4—520‑sheet tray (Tray 2)
5—520‑sheet tray (Tray 3)
6—520‑sheet tray (Tray 4)
7Multipurpose feeder
8Duplex unit
Fully configured model
1Horizontal transport unit (HTU)
2Control panel
3Finisher
4Finisher standard bin
5Finisher bin 1
6Finisher bin 2 (booklet‑maker)
7Standard 520‑sheet tray (Tray 1)
8–10The High capacity feeder includes:
8—520‑sheet tray (Tray 2)
9—867‑sheet tray (Tray 3)
10—1133‑sheet tray (Tray 4)
11Multipurpose feeder
Learning about the printer12
Downloaded From ManualsPrinter.com Manuals 
						

							12Duplex unit
Note: The finisher shown above is the booklet finisher. The standard finisher is not shown.
Understanding the control panel
Control panel itemDescription
1Display Shows messages and pictures that communicate the status of the printer
2Indicator light Indicates the printer status:
Off—The power is off.
Blinking green—The printer is warming up, processing data, or printing.
Solid green—The printer is on, but idle.
Solid red—Operator intervention is needed.
3Keypad Enter numbers or symbols on the display.
4Navigation buttons
Press  or  to scroll through menu lists.
Press 
 or  to scroll through values or text that roll to another screen.
5Select
Press  to initiate action on a menu item.
6Stop
Stops all printer activity
A list of options is offered once Stopped appears on the display.
7Menu
Opens the menu index
Note: The menus are available only when the printer is in the Ready state.
Learning about the printer13
Downloaded From ManualsPrinter.com Manuals 
						

							Control panel itemDescription
8USB Direct interface
Use this port to connect a USB flash memory device to the printer. You can print from the
connected device.
9Back
Returns the display to the previous screen
Learning about the printer14
Downloaded From ManualsPrinter.com Manuals 
						

							Installing options
Installing internal options
CAUTION—SHOCK HAZARD: If you are installing memory or option cards sometime after setting up the printer,
turn the printer off and unplug the power cord from the wall outlet before continuing. If you have any other
devices attached to the printer, turn them off as well and unplug any cables going to the printer.
You can customize your printer connectivity and memory capacity by adding optional cards. The instructions in this
section explain how to install the available cards; you can also use them to locate a card for removal.
Available options
Memory cards

Printer memory
Flash memory
Fonts
Firmware cards

Bar Code and Forms
IPDS and SCS/TNe
PrintCryptionTM
PRESCRIBE
Other internal options

Printer hard disk
RS‑232 serial interface card
Parallel 1284‑B interface card
MarkNetTM N8000 Series Internal Print Servers Installing options15
Downloaded From ManualsPrinter.com Manuals 
						

							Accessing the system board to install internal options
CAUTION—SHOCK HAZARD: Turn the printer off, and unplug the power cord from the wall outlet before
continuing. If you have any other devices attached to the printer, turn them off as well and unplug any cables
going into the printer.
Note: This operation requires a #2 Phillips screwdriver.
1Remove the cover and system board.
aTurn the screws on the cover counterclockwise, and then remove them.
bGently pull the cover and system board away from the printer, and then remove it.
2Use the illustration below to locate the appropriate connector.
Warning—Potential Damage: System board electrical components are easily damaged by static electricity.
Touch something metal on the printer before touching any system board electronic components or connectors. Installing options16
Downloaded From ManualsPrinter.com Manuals 
						

							1Firmware and flash memory card connectors
2Memory card connector
3Internal print server connector
4Hard disk connector
Installing a memory card
CAUTION—SHOCK HAZARD: If you are installing a memory card after setting up the printer, turn the printer off,
and unplug the power cord from the wall outlet before continuing.
Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
An optional memory card can be purchased separately and attached to the system board. To install the memory card:
1Access the system board.
2Unpack the memory card.
Note: Avoid touching the connection points along the edge of the card.
3Open the memory card connector latches.
Installing options17
Downloaded From ManualsPrinter.com Manuals 
						

							4Align the notches on the memory card with the ridges on the connector.
1Notches
2Ridges
5Push the memory card straight into the connector until it snaps into place.
6Reinstall the system board.
Installing a flash memory or firmware card
The system board has two connections for an optional flash memory or firmware card. Only one of each may be installed,
but the connectors are interchangeable.
CAUTION—SHOCK HAZARD: If installing a flash memory or firmware card after setting up the printer, turn the
printer off, and unplug the power cord from the wall outlet before continuing.
Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
1Access the system board.
2Unpack the card.
Note: Avoid touching the connection points along the edge of the card. Installing options18
Downloaded From ManualsPrinter.com Manuals 
						

							3Holding the card by its sides, align the plastic pins on the card with the holes on the system board.
1Plastic pins
2Metal pins
4Push the card firmly into place.
Notes:
The entire length of the connector on the card must touch and be flush against the system board.
Be careful not to damage the connectors.
5Reinstall the system board. Installing options19
Downloaded From ManualsPrinter.com Manuals 
						

							Installing a printer hard disk
CAUTION—SHOCK HAZARD: If installing a printer hard disk after setting up the printer, turn the printer off, and
unplug the power cord from the wall outlet before continuing.
Warning—Potential Damage: System board electrical components and hard disks are easily damaged by static
electricity. Touch something metal on the printer before touching any system board electronic components,
connectors, or the hard disk.
Note: A #2 Phillips screwdriver is needed to attach the hard disk to the mounting plate.
1Access the system board.
2Remove the mounting plate, hard disk, ribbon cable, and attachment screws from the package.
3Attach the ribbon cable to the hard disk.
4Attach the mounting plate to the hard disk with the screws.
Installing options20
Downloaded From ManualsPrinter.com Manuals