Home > Lexmark > Printer > Lexmark C935dn User Manual

Lexmark C935dn User Manual

Here you can view all the pages of manual Lexmark C935dn User Manual. The Lexmark manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 111

Menu itemDescription
Set Zone
Provides a list of AppleTalk zones available on the network
Note: The default setting is the default zone for the network. If no default
zone exists, the zone marked with an * is the default setting.
LexLink menu
Menu itemDescription
View Nickname
Shows the assigned LexLink nickname
Activate
On
OffActivates or deactivates LexLink support
Note: On is the factory default setting.
USB Direct menu
Menu itemDescription
USB Direct
Enable
DisableSpecifies whether support for the...

Page 112

Understanding printer messages
List of status and error messages
Activating Menu Changes
Wait for the message to clear.
Activating PPDS Mode
The PPDS emulator has been activated. Wait for the message to clear.
Bin  Full
Remove the stack of paper from the specified exit bin to clear the message.
Busy
Wait for the message to clear.
Calibrating
Wait for the message to clear.
Cancel not available
Wait for the message to clear.
Canceling
Wait for the message to clear.
Change  to 
Press  until Continue...

Page 113

Check  guides
The printer cannot determine the size of the paper.
Readjust the paper guides.
Note: To learn how to adjust the paper guides, press 
 repeatedly until Show Me appears, and then press
.
Check the tray configuration.
Clearing job accounting statistics
Wait for the message to clear.
Close cover 
1Press  until Show me appears, and then press .
An image of the cover appears.
2Close the specified cover to clear the message.
Close door 
1Press  until Show me appears, and then press .
An image of...

Page 114

Deleting
Wait for the message to clear.
Disabling DLEs
Wait for the message to clear.
Disabling Menus
Wait for the message to clear.
Note: While the menus are disabled, printer settings cannot be changed from the control panel.
Disk Corrupted. Reformat?
The printer attempted to recover a disk, but was not able to do so. Reformat appears. Press  to reformat the
disk.
Note: Reformatting the disk deletes all the files currently stored on the disk.
Disk recovery x/y XX% DO NOT POWER OFF
Wait for the message...

Page 115

Enter PIN
Enter the PIN you created in Print Properties when the confidential job was sent for printing.
Enter PIN to lock
Enter the PIN you created to lock the control panel and prevent menu changes.
Error reading USB drive
Remove the device and wait for the message to clear. The USB drive may be corrupted.
Flushing buffer
Wait for the message to clear.
Formatting Disk x/y XX% DO NOT POWER OFF
Wait for the message to clear.
Warning—Potential Damage: Do not power off while the printer is formatting the...

Page 116

Internal System Error, Reload Bookmarks
1Press  until Continue appears, and then press  to clear the message and continue printing.
2Reload the bookmarks.
Internal System Error, Reload Security Certificates
Reload the security certificates.
Press  until Continue appears, and then press  to clear the message and continue printing.
Invalid Engine Code
You need to download valid engine code for the printer.
For information about downloading code, see the Users Guide on the Software and Documentation CD....

Page 117

Load  with 
Load the paper tray or other source with the correct paper type and size.
Note: To learn how to load the specified paper source, press 
 repeatedly until Show Me appears, and then
press 
.
Cancel the current job.
Load staples 
Replace the specified staple cartridge in the finisher.
Note: To learn how to replace the specified staple cartridge, press 
 repeatedly until the Show Me message
for the specified staple cartridge appears, and then press 
.
Press  repeatedly until Continue appears, and...

Page 118

Power Saver
The printer is saving power while it waits for the next print job.
Send a job to print.
Press  to warm the printer to normal operating temperature. Afterwards, Ready appears.
Printer locked, enter PIN to unlock
The control panel is locked. Enter the correct PIN to unlock it.
Printing
Wait for the message to clear.
Programming disk DO NOT POWER OFF
Wait for the message to clear.
Warning—Potential Damage: Do not turn the printer power off while Programming disk appears on the
display....

Page 119

Remote Management Active DO NOT POWER OFF
The printer settings are being configured. Wait for the message to clear.
Warning—Potential Damage: Do not turn the printer power off while Remote Management Active appears
on the display.
Remove paper from all bins
Output bins have reached their capacity. Remove paper from all output bins to clear the message and continue printing.
Remove paper from standard bin
The standard exit bin has reached its capacity. Remove paper from the standard exit bin to clear the...

Page 120

Serial 
The printer is using a serial cable connection. The serial port is the active communication link.
Some held jobs were not restored
Press  until Continue appears, and then press  to delete the specified job.
Some held jobs will not be restored
Press  until Continue appears, and then press  to clear the message and resume printing.
Cancel the current job.
Standard Bin Full
Remove the stack of paper from the standard exit bin to clear the message.
Staples  empty or misfed
Load the specified staple...
Start reading Lexmark C935dn User Manual

Related Manuals for Lexmark C935dn User Manual

All Lexmark manuals