Lexmark C734dtn User Manual

Menu itemDescription
Job Buffering
Off
On
AutoTemporarily stores jobs on the printer hard disk before printing. This menu only
appears if a formatted disk is installed.
Notes:
Off is the factory default setting.
The On value buffers jobs on the printer hard disk. This menu selection
appears only when a formatted disk is installed and is not defective.
The Auto setting buffers print jobs only if the printer is busy processing data
from another input port.
Changing this setting from the printer control...

Menu itemDescription
Print Setup Page
Print NetWare Setup
PagePrints a report containing information about the current network setup
Notes:
The Setup Page contains information about the network printer settings, such as the
TCP/IP address.
The NetWare Setup Page menu item appears only on models that support NetWare and
shows information about NetWare settings.
Network Card menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net...

Menu itemDescription
Activate
On
OffActivates TCP/IP
Note: On is the factory default setting.
View HostnameLets you view the current TCP/IP hostname
Note: This can be changed only from the Embedded Web Server.
IP AddressLets you view or change the current TCP/IP Address
Note: Manually setting the IP address sets the Enable DHCP and Enable Auto IP
settings to Off. It also sets Enable BOOTP and Enable RARP to Off on systems that
support BOOTP and RARP.
NetmaskLets you view or change the current TCP/IP...

IPv6 menu
Use the following menu items to view or set the Internet Protocol version 6 (IPv6) information.
Note: This menu is available only for network models or printers attached to print servers.
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > IPv6
Menu itemDescription
Enable IPv6
On
OffEnables IPv6 in the printer
Note: On is the factory default setting.
Auto Configuration
On
OffSpecifies whether the network adapter...

Menu itemDescription
View Signal QualityLets you view the quality of the wireless connection
View Security ModeLets you view the encryption method for the wireless connection.
“Disabled” indicates that the wireless network is not encrypted.
AppleTalk menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > AppleTalk
Menu itemDescription
Activate
Yes
NoActivates AppleTalk support
Note: Yes is the factory default setting.
View...

Menu itemDescription
Select SAP Frames
Ethernet 802.2
Ethernet 802.3
Ethernet Type II
Ethernet SNAPEnables the Ethernet frame type setting
Note: On is the factory default setting for all menu items.
Packet Burst
Yes
NoReduces network traffic by allowing the transfer and acknowledgement of
multiple data packets to and from the NetWare server
Note: Yes is the factory default setting.
NSQ/GSQ Mode
Yes
NoSpecifies the NSQ/GSQ Mode setting
Note: Yes is the factory default setting.
LexLink menu
This menu is...

Menu itemDescription
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if the PCL
Smartswitch setting is On. It uses the default printer language specified in the
Setup menu if the PCL SmartSwitch...

Menu itemDescription
ENA AddressSets the network address information for an external print server that is attached to
the printer using a USB cable
Note: This menu item is available only if the printer is attached to an external print
server through the USB port.
ENA NetmaskSets the netmask information for an external print server that is attached to the
printer using a USB cable
Note: This menu item is available only if the printer is attached to an external print
server through the USB port.
ENA...

Menu itemDescription
Parallel Buffer
Disabled
Auto
3k to Sets the size of the parallel input buffer
Notes:
Auto is the factory default setting.
The Disabled setting turns off job buffering. Any jobs already buffered on the
disk are printed before normal processing is resumed.
The parallel buffer size setting can be changed in 1k increments.
The maximum size allowed depends on the amount of memory in the printer,
the size of the other link buffers, and whether Resource Save is set to On or
Off.
To...

Menu itemDescription
Parallel Mode 2
On
OffDetermines whether or not the parallel port data is sampled on the leading or trailing
edge of strobe
Note: On is the factory default setting.
Mac Binary PS
On
Off
AutoSets the printer to process Macintosh binary PostScript print jobs
Notes:
Auto is the factory default setting.
The Off setting filters print jobs using the standard protocol.
The On setting processes raw binary PostScript print jobs.
ENA Address
...Sets the network address information for an...