Lenovo 3000 J Series Manual

Diagnostic Error Code FRU/Action 
015-036-XXX 
USB port Register error 
System board 
015-040-XXX 
USB port IRQ failure 1.   
 Run setup and check for conflicts 
2. 
 
 Flash the system. See “Flash update 
procedures” on page 207 
3. 
 
 System board 
015-195-XXX 
USB port Test aborted by user 
Information only 
Re-start the test, if necessary 
015-196-XXX 
USB port test halt, error threshold exceeded 1. 
 
 Press F3 to review the log file 
2. 
 
 Re-start the test to reset the log file 
015-197-XXX 
USB...

Diagnostic Error Code FRU/Action 
018-197-XXX 
PCI Card test warning 1.   
 Make sure the component that is called 
out is connected and/or enabled. See 
Chapter 6, “Using the Setup Utility,” on 
page 51 
2. 
 
 Re-run test 
3. 
 
 Replace the component that is called out 
in warning statement 
4. 
 
 Replace the component under test 
018-198-XXX 
PCI Card test aborted 1. 
 
 If a component is called out, make sure 
it is connected and/or enabled. See 
Chapter 6, “Using the Setup Utility,” on 
page 51...

Diagnostic Error Code FRU/Action 
020-198-XXX 
PCI test aborted 1.   
 If a component is called out, make sure 
it is connected and/or enabled. See 
Chapter 6, “Using the Setup Utility,” on 
page 51 
2. 
 
 Flash the system and re-test. See “Flash 
update procedures” on page 207 
3. 
 
 Go to “Undetermined problems” on page 
81 
020-199-XXX 
PCI test failed, cause unknown 1. 
 
 Go to “Undetermined problems” on page 
81 
2. 
 
 Flash the system and re-test. See “Flash 
update procedures” on page 207 
3....

Diagnostic Error Code FRU/Action 
025-198-XXX 
IDE interface test aborted 1.   
 If a component is called out, make sure 
it is connected and/or enabled. See 
Chapter 6, “Using the Setup Utility,” on 
page 51 
2. 
 
 Flash the system and re-test. See “Flash 
update procedures” on page 207 
3. 
 
 Go to “Undetermined problems” on page 
81 
025-199-XXX 
IDE interface test failed, cause unknown 1. 
 
 Go to “Undetermined problems” on page 
81 
2. 
 
 Flash the system and re-test. See “Flash 
update...

Diagnostic Error Code FRU/Action 
030-198-XXX 
SCSI interface test aborted 1.   
 If a component is called out, make sure 
it is connected and/or enabled. See 
Chapter 6, “Using the Setup Utility,” on 
page 51 
2. 
 
 Flash the system and re-test. See “Flash 
update procedures” on page 207 
3. 
 
 Go to “Undetermined problems” on page 
81 
030-199-XXX 
SCSI interface test failed, cause unknown 1. 
 
 Go to “Undetermined problems” on page 
81 
2. 
 
 Flash the system and re-test. See “Flash 
update...

Diagnostic Error Code FRU/Action 
071-00X-XXX 
071-01X-XXX 
071-02X-XXX
Audio
 port error 
1.   
 Run Setup 
2. 
 
 Flash the system. See “Flash update 
procedures” on page 207 
3. 
 
 System board 
071-03X-XXX 
Audio port failure 1. 
 
 Speakers 
2. 
 
 Microphone 
3. 
 
 Audio card, if installed 
4. 
 
 System board 
071-04X-XXX 
Audio port failure 1. 
 
 Run Setup 
2. 
 
 Audio card, if installed 
3. 
 
 System board 
071-195-XXX 
Audio port Test aborted by user 
Information only 
Re-start the test,...

Diagnostic Error Code FRU/Action 
080-196-XXX 
Game Port interface test halt, error threshold 
exceeded 
1.   
 Press F3 to review the log file 
2. 
 
 Re-start the test to reset the log file 
080-197-XXX 
Game Port interface test warning 1. 
 
 Make sure the component that is called 
out is connected and/or enabled. See 
Chapter 6, “Using the Setup Utility,” on 
page 51 
2. 
 
 Re-run test 
3. 
 
 Replace the component that is called out 
in warning statement 
4. 
 
 Replace the component under test...

Diagnostic Error Code FRU/Action 
086-197-XXX 
Mouse Port interface test warning 1.   
 Make sure the component that is called 
out is connected and/or enabled. See 
Chapter 6, “Using the Setup Utility,” on 
page 51 
2. 
 
 Re-run test 
3. 
 
 Replace the component that is called out 
in warning statement 
4. 
 
 Replace the component under test 
086-198-XXX 
Mouse Port interface test aborted 1. 
 
 If a component is called out, make sure 
it is connected and/or enabled. See 
Chapter 6, “Using the Setup...

Diagnostic Error Code FRU/Action 
170-0XX-XXX 
Voltage Sensor(s) failure 1.   
 Flash system 
2. 
 
 System board 
170-195-XXX 
Voltage Sensor(s) Test aborted by user 
Information only 
Re-start the test, if necessary 
170-196-XXX 
Voltage Sensor(s) test halt, error threshold 
exceeded 
1. 
 
 Press F3 to review the log file 
2. 
 
 Re-start the test to reset the log file 
170-197-XXX 
Voltage Sensor(s) test warning 1. 
 
 Make sure the component that is called 
out is connected and/or enabled. See...

Diagnostic Error Code FRU/Action 
175-197-XXX 
Thermal Sensor(s) test warning 1.   
 Make sure the component that is called 
out is connected and/or enabled. See 
Chapter 6, “Using the Setup Utility,” on 
page 51 
2. 
 
 Re-run test 
3. 
 
 Replace the component that is called out 
in warning statement 
4. 
 
 Replace the component under test 
175-198-XXX 
Thermal Sensor(s) test aborted 1. 
 
 If a component is called out, make sure 
it is connected and/or enabled 
2. 
 
 Flash the system and re-test....