Land Rover Range Rover Owners Handbook Lm 2nd Edition Exp Rover

							Door Mirrors
50
Do or Mirro rsEXTERIOR MIRRORS
NOTE: Objects viewed in exterior mirrors may 
appear further away than they actually are.
Mirror adjustment
•Move the lower control (2) to the left or 
right-hand position to select either the left 
or right hand mirror.
•With the starter switch turned to position 
‘II’, push the appropriate arrow on the 
mirror adjust control (1) to tilt the mirror 
glass up/down/left or right.
The door mirrors have integral heating 
elements which disperse ice or mist from the 
glass. These will operate automatically with the 
starter switch in position ‘II’, depending on 
external temperature.
NOTE: On vehicles fitted with the driver’s seat 
memory facility, up to three different exterior 
mirror positions can be stored in the seat 
memory, this enables the driver to recall the 
optimum mirror position at the touch of a 
button - for further information, please refer to 
‘DRIVER’S SEAT MEMORY FACILITY*’, 
page 32.Folding the mirror body
The door mirrors are designed to fold forwards 
or rearwards on impact. They can also be folded 
back towards the side windows into a ‘park’ 
position to enable the vehicle to negotiate 
narrower openings.
Manual operation: On some vehicles this 
operation can be carried out manually, by 
physically pushing the mirror bodies back 
towards the side windows, and then pulling 
them back into the normal (extended) 
positions. 
H3868
1
2
H3926 
						

							Door Mirrors
51
Electric operation*: Press the mirror-fold 
button (arrowed in inset) once to fold the 
mirrors into the side windows. Press again to 
return the mirrors to the driving position.
NOTE: Electric mirror folding is disabled if 
vehicle speed exceeds 10 km/h.
If the mirrors are accidentally knocked out of 
position (i.e. with one mirror extended and the 
other in the ‘parked’ position), an additional 
operation of the switch will re-synchronise 
them.
Automatic dimming
*
On some models, the mirrors are equipped with 
an electrochromatic dimming function that 
‘dims’ the mirror to reduce glare from the 
headlights of following vehicles at night.Automatic ‘kerb-view’ dipping
*
Vehicle’s fitted with driver’s seat memory have 
a pre-stored function, which causes the 
nearside mirror to dip automatically whenever 
reverse gear is selected. This facility is only 
available if the mirror select button (‘1’ on 
previous page), is set to the driver’s side.
H4002 
						

							Instruments
52
InstrumentsINSTRUMENT PANEL
1. Fuel gauge
The pointer drops to zero when the starter 
switch is turned off, but quickly rises to show 
the level of fuel in the tank when the switch is 
turned to position ‘II’. After refuelling, the 
gauge rapidly rises to reflect the increase of fuel 
in the tank.
When the fuel remaining in the tank is a 
minimum of 12 litres on petrol vehicles, or 
10 litres on diesel vehicles, the AMBER low fuel 
warning light in the fuel gauge illuminates. If the 
light illuminates, refuel at the first opportunity.
The small arrow visible in the fuel pump symbol 
on the gauge indicates the side of the vehicle on 
which the fuel filler is located - a useful 
reminder to help you position the vehicle on the 
correct side of the forecourt pumps before 
refuelling. WARNING
NEVER allow vehicles to run out of fuel (the 
resultant misfire may destroy the catalytic 
converter).
2. Speedometer
Indicates road speed in kilometres per hour.
3. Tachometer
Indicates engine speed in revolutions per 
minute (x 1000). In normal driving conditions 
the engine is most fuel efficient between 2000 
and 3000 rev/min.
H3817
1234
9756108 
						

							Instruments
53
4. Temperature gauge
Once the engine coolant has reached its normal 
operating temperature, the pointer will rise to a 
position midway between the RED and BLUE 
segments of the gauge (the precise position will 
vary according to climatic conditions).
If the pointer moves towards the RED segment, 
this indicates that the engine coolant is 
becoming too hot. Should the pointer move 
INTO the RED segment and the RED warning 
light within the gauge illuminates, severe 
engine damage could occur (under these 
circumstances, the air conditioning may switch 
off and engine performance may reduce in 
order to minimise engine load).
Stop the vehicle as soon as safety permits and 
switch off the engine and allow to cool down. If 
the problem persists, seek qualified assistance 
before continuing.
5. System check control
With the starter key NOT inserted, press and 
hold the control to check whether any system 
malfunctions have occurred. If faults exist, they 
will be listed in turn in the main message centre 
until the control is released. If no malfunctions 
have occurred, ‘CHECK CONTROL OK’ is 
displayed. See ‘MAIN MESSAGE CENTRE’, 
page 55, for further information. Any messages 
will also be displayed during driving and when 
the starter switch is turned off.
6. Gear selector position display
This shows the current gear lever position and 
indicates when low range has been selected. 
See ‘GEAR SELECTOR DISPLAY’, page 61, for 
further information.7. Main message centre
Displays all warning and information messages 
submitted by the vehicle systems. For further 
information concerning messages and their 
meanings, refer to ‘MAIN MESSAGE CENTRE’, 
page 55.
8. Total distance (odometer) and trip recorder
With the starter switch turned to position ‘II’, 
the display indicates the total distance travelled 
by the vehicle, and also shows the most recent 
individual journey distance. In some markets, 
the display can be set to show either miles or 
kilometres. To convert from one to another, 
press and hold the trip recorder reset button for 
more than two seconds. 
9. Service interval indicator
This shows the distance remaining before the 
next oil service or inspection is due. See 
‘SERVICE INTERVAL INDICATOR’, page 61, for 
further information.
10. Trip recorder reset button
Press briefly to return the trip recorder display 
to zero.  
						

							Trip Computer
54
Trip Co mputerTRIP COMPUTER - FUNCTION 
SELECTION
The trip computer utilises the message centre 
in the instrument pack and provides useful 
information to assist the driver to calculate fuel 
stops, journey times and distances.When the starter switch is in position ‘II’, the 
different trip computer statistics can be viewed 
in turn by pressing the button on the end of the 
direction indicator stalk repeatedly until the 
relevant statistic is displayed. The statistics are 
displayed in the following order:
•The current time.
•Fuel consumption 1.
•Fuel consumption 2.
•Range.
•Speed limit.
•Distance (from destination).
•Estimated time of arrival.
•Average speed.
•Time 1
* (park heating only).
•Time 2
* (park heating only).
•Stopwatch.
The driver has the option to select which of the 
above functions are displayed and also in which 
order. For further information, consult your 
‘In-Car Entertainment’ or ‘Audio, TV & 
Navigation System’ book.
H4076 
						

							Message Centres
55
Me ss age  Ce ntresMAIN MESSAGE CENTRE
1.Digital odometer. Displays the total 
distance travelled by the vehicle.
2.Trip recorder. Displays the distance 
travelled in kilometres for individual 
journeys. 
3.External temperature display.
4.Warning message and information 
display.
Driver warning and information messages are
displayed in the message centre. Messages 
have different priority levels and are grouped 
into the following categories.
Messages are displayed when a fault is 
detected and also when the starter switch is 
turned off. It is also possible to view messages 
for up to 3 minutes after the key has been 
removed from the starter switch, by pressing 
the system check control switch.Critical warning messages
Critical warning messages are accompanied
by an audible warning and the warning is 
flanked by two flashing arrows. Critical warning 
messages are displayed continuously while the 
starter switch is turned on, and remain 
displayed while the fault persists.
DO NOT ignore these messages - TAKE 
CORRECTIVE ACTION IMMEDIATELY!
Warnings and information messages
Warning messages are non-critical, but must
be treated with some urgency. They will also
be accompanied by an audible warning each 
time the message is displayed.
DO NOT ignore these messages - TAKE 
CORRECTIVE ACTION IMMEDIATELY.
Warning messages are displayed for 
approximately 20 seconds. If other warning 
messages are pending, the display time will be 
reduced to approximately 2 seconds.
Information messages will be displayed as and 
when applicable, and also when the starter 
switch is turned on or off. Where the message 
requires action by the driver - TAKE 
CORRECTIVE ACTION AS SOON AS POSSIBLE.
H3820
1
4
23 
						

							Message Centres
56
WARNING & INFORMATION MESSAGES
Warnings and information messages appear in order of importance, with critical warnings taking 
priority. Critical warnings are indicated by flashing arrows appearing on either side of the message. 
Action should be taken immediately if a critical warning is displayed.
MessageMeaningWhat to do?
ACCESS MAX 40KM/H Crawl mode is selected.  Do not drive at speeds exceeding 40 
km/h whilst in crawl mode or the 
vehicle will return to standard 
height.
AIR SUSP.INACTIVE 
+ MAX 60 km/h 
(alternating message)The air suspension system has 
overheated and has temporarily 
shut down.Drive with caution and be aware that 
the air suspension system will have 
reduced functionality. If message 
persists for more than 25 minutes, 
have the vehicle checked by a dealer 
as soon as possible.
APPLY HANDBRAKE The vehicle is in ‘P’ (Park) and 
transfer neutral has been selected 
and the starter switch has been 
turned off, but the handbrake has 
not been applied.Apply the handbrake, or if the vehicle 
is to be towed on all four wheels, 
turn the starter switch to position ‘I’ 
or ‘II’.
CHECK BRAKE FLUID Fluid level is too low. Stop the vehicle as soon as safety 
permits and top-up the brake fluid. 
Have the source of a possible leak 
checked by your dealer.
CHECK BRAKE PADS The brake pads are reaching their 
wear limit.Drive cautiously and consult your 
dealer at the earliest opportunity.
CHECK CONTROL OK No system faults have been 
detected by the vehicle 
diagnostics system.No action required.
CHECK COOLANT LEVEL Coolant level is too low. Top-up with the correct mixture of 
antifreeze and water at the earliest 
opportunity. If the problem persists, 
consult your dealer.
CHECK DIP BEAM LIGHT A bulb has failed or there is a fault 
in the electrical circuit.Check/replace the bulb or consult 
your dealer.
CHECK ENGINE OIL LEV The oil level is at the absolute 
minimum.Stop the vehicle as soon as safety 
permits and top-up the engine oil to 
the correct level.
CHECK FRONT FOGLIGHT A bulb has failed or there is a fault 
in the electrical circuit.Check/replace the bulb or consult 
your dealer. 
						

							Message Centres
57
CHECK FRONT LIGHT More than one front light is 
defective.Check which lights are defective, 
replace any failed bulb. If a light is 
still defective, have the fault rectified 
by a dealer.
CHECK FUEL TANK CAP
* 
(only in some markets)The fuel filler cap is not fitted 
correctly.Check the cap and tighten/fit 
correctly.
CHECK MAINBEAM LIGHT A bulb has failed or there is a fault 
in the electrical circuit.Check/replace the bulb or consult 
your dealer.
CHECK NUMPLATE LIGHT A bulb has failed or there is a fault 
in the electrical circuit.Check/replace the bulb or consult 
your dealer.
CHECK REAR FOGLIGHT A bulb has failed or there is a fault 
in the electrical circuit.Check/replace the bulb or consult 
your dealer.
CHECK REAR LIGHT More than one rear light is 
defective.Check which lights are defective and 
replace any failed bulb. If the light is 
still defective, have the fault rectified 
by a dealer.
CHECK SIDE LIGHT A bulb has failed or there is a fault 
in the electrical circuit.Check/replace the bulb or consult 
your dealer.
CHECK TAIL LIGHT A bulb has failed or there is a fault 
in the electrical circuit.Check/replace the bulb or consult 
your dealer.
CHECK TRAILER LIGHT A bulb has failed or there is a fault 
in the electrical circuit.Check/replace the bulb or consult 
your dealer.
CHECK TYRE PRESSURE
*Tyre pressures have dropped. Check the tyre pressures at the 
earliest opportunity and inflate to the 
specified pressures.
COOLANT TEMPERATURE Coolant temperature is too high. Stop the vehicle as soon as safety 
permits and switch off the engine 
and allow to cool down. Consult 
your dealer at the earliest 
opportunity.
DOOR OPEN A door is open (displayed as the 
vehicle moves off from 
stationary).Stop the vehicle as soon as safety 
permits and close the door.
DSC INACTIVE A fault has been detected in the 
DSC system.The vehicle is driveable, but proceed 
with caution. Consult your dealer at 
the earliest opportunity.
EEPROM LCMC The main lighting switch has a 
fault.Consult your dealer at the earliest 
opportunity.
MessageMeaningWhat to do? 
						

							Message Centres
58
ENGINE FAILSAFE PROG A fault has been detected in the 
engine electronics.The vehicle is driveable, but with 
reduced engine speed and power. 
Drive with caution, and consult your 
dealer at the earliest opportunity. 
Note that the engine will be more 
prone to stalling and difficulties 
starting.
EXTERNAL TEMP XºC/F The exterior temperature is equal 
to or less than 3ºC.This indicates freezing conditions, 
appropriate defrosting precautions 
should be taken before driving and 
ice may be present on the roads.
FASTEN SEAT BELTS The driver’s or front passenger’s 
seat belt is not correctly fastened.Ascertain which seat belt is undone 
and correctly fasten the belt.
FUEL INJECT.SYSTEM A fault has been detected in the 
fuel injection system.Seek qualified assistance.
HDC INACTIVE A fault in the Hill Descent Control 
system has occurred.Do not attempt the planned 
descent/ascent and consult your 
dealer at the earliest opportunity.
HDC TEMP.NOT AVAIL. The Hill Descent Control system 
has been over-used and 
temporarily shut down. Do not attempt the planned 
descent/ascent until the system has 
cooled (the message is no longer 
displayed).
HEADLIGHT DELAY You have selected headlight delay 
- headlights will switch off 
automatically.No action required.
HIGH RANGE HIGH range has been selected in 
the transfer gearbox.Select LOW range if HIGH range is 
not required.
KEY BATTERY LOW The battery in the handset key is 
low on charge.Replace the handset key battery.
KEY IN IGNITION LOCK
* 
(only in some markets)The key has been left in the starter 
switch and the driver’s door has 
been opened.Remove the key from the starter 
switch.
LIGHTS ON The key has been removed from 
the starter switch and the lights 
have been left on.Turn the light switch to the off 
position, if the lights are no longer 
required.
LOW RANGE LOW range has been selected in 
the transfer gearbox.Select HIGH range if LOW range is 
not required.
LOW SCREENWASH Fluid level is too low. Top-up the washer reservoir at the 
earliest opportunity.
MANUAL MODE The transmission is in manual 
mode.Select automatic mode if manual 
mode is no longer required.
MessageMeaningWhat to do? 
						

							Message Centres
59
NO  HDC, SLOW  DOWN The Hill Descent Control operating 
speed range of 0 - 35 km/h has 
been exceeded, or an attempt to 
select HDC has been made whilst 
the vehicle is exceeding the 
operating speed range.Slow down to below 35 km/h to use 
or select HDC.
OFFROAD MAX 50KM/H Vehicle speed is exceeding 
45 km/h, while at off-road height.Do not drive at speeds exceeding 50 
km/h whilst at off-road height. 
Otherwise the vehicle will return to 
standard height.
PRE-HEATING The vehicle’s preheating system 
has been activated.Deactivate the system if not 
required.
RELEASE HANDBRAKE The handbrake is applied and a 
drive gear is selected.Release the handbrake.
SELECT NEUTRAL You have attempted to change 
gear ranges without the gearbox 
being in NEUTRAL.Select neutral in the main gearbox.
SET TYRE PRESSURE
*The TPMS (tyre pressure 
monitoring system) has accepted 
the current tyre pressures as the 
set value.If the tyre pressures are correct, take 
no action.
If the tyre pressures are incorrect, 
inflate the tyres to their correct 
pressure and reset the TPMS.
SLOW DOWN Your current road speed is too 
high to perform a transfer box 
range change.Slow the vehicle to the required 
speed before changing range.
SPEED LIMIT
*You are exceeding the set 
maximum speed limit.Slow down to conform with the 
speed limit.
SPORT MODE The transmission is in sport 
mode.Select automatic mode if sport mode 
is no longer required.
STOP!ENGINE OILPRESS Engine oil pressure is too low. Stop the vehicle as soon as safety 
permits and switch off the engine. 
Check the oil level, top-up if 
necessary - if okay, consult your 
dealer before driving.
TAILGATE OPEN The tailgate is open as the vehicle 
moves off from stationary for the 
first time.Stop the vehicle as soon as safety 
permits and close the tailgate.
TRAILER MODE A suspension height change 
request has been made whilst the 
vehicle is being used for towing. 
No change occurs.Do not attempt to change 
suspension height when towing - the 
vehicle must remain at standard 
height.
MessageMeaningWhat to do?