Land Rover Discovery Series Ii 2001my Owners Handbook Nas Rover

							Fuses
190
ENGINE COMPARTMENT FUSE BOX
WARNING
Batteries emit explosive hydrogen gas; 
ensure that sparks, flames and other ignition 
sources are kept away from the engine 
compartment.
A second fuse box is located on the right side of 
the engine compartment adjacent to the coolant 
reservoir.
Press all four latches in the direction of the 
arrows shown on the illustration to release the 
fuse box cover.
Information on the underside of the cover 
identifies the fuses and their ratings.  This 
information is also listed on the following page.
When replacing the cover, locate the four 
latches, then push firmly downwards until the 
latches can be heard to ‘snap’ closed.Owners are advised against removing or 
replacing the relays (identified as R1-R14) 
and fusible links (FL1-FL13).  Failure of any of 
these items should be investigated by a 
qualified technician.
WARNING
To prevent a possible fire or damage to the 
electrical system, only fit fuses of the same 
rating or type. DO NOT replace a blown fuse 
with a fuse of a higher amperage rating. 
Always rectify the cause of the failure before 
replacing a fuse. Seek qualied assistance if 
necessary.
H2497
H2498 
						

							Fuses
191
Fuse specification
Fuse numberRating (amps)Circuit protected
1 30 Fuel injectors (Petrol models)
2 15 Engine management system
3 15 Front fog lights
4 20 Headlight washers
5 40 Cooling fans
6 10 Air conditioning
7 40 Heated front screen - LH
8 40 Heated front screen - RH
9 30 Trailer lights
10 30 Fuel pump
11 30 ABS valve
12 20 Automatic gearbox
13 10 Body Control Unit (BCU)
14 15 Direction indicators
Hazard lights
15 15
Active cornering enhancement (ACE)
*
16 10 Horn 
						

							Fuses
192
UNDERSEAT FUSES
Two identical small fuse blocks are situated one 
beneath each front seat.
Fuse specification
H2609
Fuse numberRating (amps)Circuit protected
1 40 Seat electrics
2 3 Lumbar support - pump
3 3 Lumbar support - solenoid 
						

							Bulb Replacement
193
B ulb Re plac emen tREPLACING BULBS
Check the operation of all exterior lights before 
you drive the vehicle.
Replacement bulbs
NOTE: All bulbs must be rated at 12 voltsHalogen bulbs
Halogen bulbs are used for dipped/high, 
supplementary high beam and front fog lights.  
Take care NOT to touch this type of bulb with 
your fingers; always use a cloth to handle them.  
If necessary, clean the bulb with isopropyl 
rubbing alcohol to remove fingerprints.
IMPORTANT INFORMATION
Before replacing a bulb, always switch off 
the starter switch and appropriate lighting 
switch to prevent any possibility of a short 
circuit. Only replace bulbs with the same 
type and specification.
BulbWatts
Headlights dipped/high beam 60/55
Front side lights 5 
Front side marker lights 5 
Direction indicators 21 
Front fog lights 55
Side repeater lights 5 
Reverse lights 21 
Rear fog guard lights 21 
Tail lights 5
Stop lights 21
High mounted stop light 21
Number plate lights 5
Interior light 5
Interior courtesy lights 10
Glovebox light 5
Vanity mirror light 1.2 
						

							Bulb Replacement
194
HEADLIGHT AND SIDELIGHT
Light unit removal
First remove the access panel set into the 
bonnet locking platform above each headlight.To replace either the headlight or sidelight bulb, 
remove the light unit as follows:
Disengage the retaining clips ‘A’ and rotate 
them approximately 10 degrees (see inset) until 
they align with the slots in the headlight 
mounting panel. The light unit can now be 
released forward.
NOTE: DO NOT screw or unscrew the retaining 
clips more than described - their position 
affects the alignment of the headlights.
H2657
A
A
H3101 
						

							Bulb Replacement
195
Headlight bulb replacement
Disconnect the electrical multi-plug and 
remove the rubber cover. Release the spring 
clip which holds the bulb and withdraw the 
bulb from the light unit. When replacing the 
bulb, ensure that the larger tab is pointing 
towards the top of the headlight.
Replace the spring clip and rubber cover, 
ensuring the slit in the cover is at the top of the 
headlight, and pressing the centre firmly to seal 
around the electrical contacts of the bulb.
NOTE: Do not touch the bulb glass with your 
fingers. If necessary, clean the bulb with 
isopropyl rubbing alcohol. 
Replacing the headlight unit
Replacement is a reversal of the removal 
procedure.Sidelight bulb replacement
With the light unit removed (see previous 
instructions), disconnect the electrical 
multi-plug and disengage the bulb holder by 
twisting a quarter turn anti-clockwise. Pull the 
bulb from the holder to remove.
H3100 
						

							Bulb Replacement
196
FRONT DIRECTION INDICATOR AND SIDE 
MARKER LIGHT
Remove the retaining screw ‘A’, then ease the 
light unit forward torelease it from the vehicle.
Both the small side marker light and larger 
direction indicator bulb holders are released 
from the light unit by twisting anti-clockwise.
Pull the side marker bulb to remove.  Push and 
twist the direction indicator bulb to remove.
To replace the light unit, insert the two location 
pins (arrowed) on the outer side of the light unit 
into the vehicle body, push firmly into position 
and, finally, replace the retaining screw.
SIDE REPEATER LIGHT
Push the lens firmly to the left and withdraw the 
light unit from the wing. Twist to release the 
bulb holder from the lens unit, then pull the 
bulb from its socket.
When refitting, ensure that the little tabs 
(arrowed in illustration) are pointed to the right 
and are inserted into the aperture before 
pushing the light unit into position in the wing.
H2504
A
H2520 
						

							Bulb Replacement
197
REAR LIGHT CLUSTER 
(Tail, stop & reverse lights) 
From outside the vehicle remove the four 
retaining screws to release the light unit from 
the vehicle, then detach the electrical multi-plug
connector, by pressing the metal retaining 
spring.
To gain access to the bulbs, remove the five 
screws from the rear of the light unit and detach 
the bulb holder.  Push and twist to release each 
bulb.
H2506 
						

							Bulb Replacement
198
BUMPER MOUNTED LIGHTS
(Fog guard lights & direction indicators)
WARNING
If the engine is warm, the exhaust system 
may be hot - to prevent personal injury, avoid 
contact with a hot exhaust system when 
reaching behind the bumper.
Reach behind the bumper and press the spring 
clip ‘A’ to release the light unit.
Squeeze both levers ‘B’ to release the bulb 
holder from the lens. Push and twist to release 
the bulbs.
NOTE: If necessary, the light unit can first be 
detached from the electrical harness by 
releasing the multi-plug from the rear of the 
bulb holder.Before reassembling the light unit, make sure 
the seal (between holder and lens) is in place.
To replace the light unit, first locate the hooks 
‘C’ in the bumper aperture and firmly push the 
other side of the light against spring pressure 
until it clicks into place.
H2522
C
B
A 
						

							Bulb Replacement
199
NUMBER PLATE LIGHTS
Remove both screws to release the light unit.  
Ease the light unit from its recess and pull the 
bulb to remove. 
HIGH MOUNTED STOP LIGHT
Remove both retaining screws and the cover 
from the rear of the light unit. Twist the bulb 
holder anti-clockwise to remove. Push and 
twist anti-clockwise to release the bulb.
H2499
H2501