Land Rover Discovery Series Ii 2001my Owners Handbook Nas Rover

Fuses
190
ENGINE COMPARTMENT FUSE BOX
WARNING
Batteries emit explosive hydrogen gas; 
ensure that sparks, flames and other ignition 
sources are kept away from the engine 
compartment.
A second fuse box is located on the right side of 
the engine compartment adjacent to the coolant 
reservoir.
Press all four latches in the direction of the 
arrows shown on the illustration to release the 
fuse box cover.
Information on the underside of the cover 
identifies the fuses and their ratings.  This 
information...

Fuses
191
Fuse specification
Fuse numberRating (amps)Circuit protected
1 30 Fuel injectors (Petrol models)
2 15 Engine management system
3 15 Front fog lights
4 20 Headlight washers
5 40 Cooling fans
6 10 Air conditioning
7 40 Heated front screen - LH
8 40 Heated front screen - RH
9 30 Trailer lights
10 30 Fuel pump
11 30 ABS valve
12 20 Automatic gearbox
13 10 Body Control Unit (BCU)
14 15 Direction indicators
Hazard lights
15 15
Active cornering enhancement (ACE)
*
16 10 Horn 

Fuses
192
UNDERSEAT FUSES
Two identical small fuse blocks are situated one 
beneath each front seat.
Fuse specification
H2609
Fuse numberRating (amps)Circuit protected
1 40 Seat electrics
2 3 Lumbar support - pump
3 3 Lumbar support - solenoid 

Bulb Replacement
193
B ulb Re plac emen tREPLACING BULBS
Check the operation of all exterior lights before 
you drive the vehicle.
Replacement bulbs
NOTE: All bulbs must be rated at 12 voltsHalogen bulbs
Halogen bulbs are used for dipped/high, 
supplementary high beam and front fog lights.  
Take care NOT to touch this type of bulb with 
your fingers; always use a cloth to handle them.  
If necessary, clean the bulb with isopropyl 
rubbing alcohol to remove fingerprints.
IMPORTANT INFORMATION
Before...

Bulb Replacement
194
HEADLIGHT AND SIDELIGHT
Light unit removal
First remove the access panel set into the 
bonnet locking platform above each headlight.To replace either the headlight or sidelight bulb, 
remove the light unit as follows:
Disengage the retaining clips ‘A’ and rotate 
them approximately 10 degrees (see inset) until 
they align with the slots in the headlight 
mounting panel. The light unit can now be 
released forward.
NOTE: DO NOT screw or unscrew the retaining 
clips more than described...

Bulb Replacement
195
Headlight bulb replacement
Disconnect the electrical multi-plug and 
remove the rubber cover. Release the spring 
clip which holds the bulb and withdraw the 
bulb from the light unit. When replacing the 
bulb, ensure that the larger tab is pointing 
towards the top of the headlight.
Replace the spring clip and rubber cover, 
ensuring the slit in the cover is at the top of the 
headlight, and pressing the centre firmly to seal 
around the electrical contacts of the bulb.
NOTE: Do not...

Bulb Replacement
196
FRONT DIRECTION INDICATOR AND SIDE 
MARKER LIGHT
Remove the retaining screw ‘A’, then ease the 
light unit forward torelease it from the vehicle.
Both the small side marker light and larger 
direction indicator bulb holders are released 
from the light unit by twisting anti-clockwise.
Pull the side marker bulb to remove.  Push and 
twist the direction indicator bulb to remove.
To replace the light unit, insert the two location 
pins (arrowed) on the outer side of the light unit 
into...

Bulb Replacement
197
REAR LIGHT CLUSTER 
(Tail, stop & reverse lights) 
From outside the vehicle remove the four 
retaining screws to release the light unit from 
the vehicle, then detach the electrical multi-plug
connector, by pressing the metal retaining 
spring.
To gain access to the bulbs, remove the five 
screws from the rear of the light unit and detach 
the bulb holder.  Push and twist to release each 
bulb.
H2506 

Bulb Replacement
198
BUMPER MOUNTED LIGHTS
(Fog guard lights & direction indicators)
WARNING
If the engine is warm, the exhaust system 
may be hot - to prevent personal injury, avoid 
contact with a hot exhaust system when 
reaching behind the bumper.
Reach behind the bumper and press the spring 
clip ‘A’ to release the light unit.
Squeeze both levers ‘B’ to release the bulb 
holder from the lens. Push and twist to release 
the bulbs.
NOTE: If necessary, the light unit can first be 
detached from the...

Bulb Replacement
199
NUMBER PLATE LIGHTS
Remove both screws to release the light unit.  
Ease the light unit from its recess and pull the 
bulb to remove. 
HIGH MOUNTED STOP LIGHT
Remove both retaining screws and the cover 
from the rear of the light unit. Twist the bulb 
holder anti-clockwise to remove. Push and 
twist anti-clockwise to release the bulb.
H2499
H2501