Land Rover Defender 90 110 Workshop 1984 Rover Manual

CHASSIS AND BODY El 
.. . . .... r”,,.. ’: ., , . :I 4.:: : . ... .~. 
A FrontDatum 
B Chassis Datum 
C Front axle centre line 
D  Rear axle centre 
line 
1. 4148 - 4143 mm 
2. 40093-4005 mm 
3. 978,7-981,2 mm 
4. 22-20” 
5. 252-250 mm 
6. 239-236,5 mm 
7. 3023,3-3022,3 mm 
8. 3030,7-3028,7 mm 
9. 155- 153 mm 
10. 871,2-869,2 mm 
11.  2794 mm - Wheelbase 
12. 488 - 433 mm 
13. 488 - 433 mm 
14. 82-79,5 mm 
15. 750,9 mm 
16. 750,9 mm 
17. 4393 - 4363 mm 
18. 4393 -4363 mm 
19. 2993 - 2953 mm 
20. 500-495...

.  

CHASSIS AND BODY 1761 
DOORS - 1986 ONWARDS 
7  

176 I CHASSIS AND BODY 
REMOVING THE DOOR TRIM - Front and rear 
doors 
1. Prise off the  two  finishers  and remove  the two 
screws  securing  the door  pull. 
-. -- .___ - ...- . 
1. 
5. Lever off the window  regulator center finisher and 
remove  the retaining  screw and withdraw  the 
handle  and bezel. 
2. Remove the single Screw behind the remote control 6- Using a screwdriver, the trim away 
lever. from the door. 
3. Prise off the remote  control  lever bezel. Fitting  door trim 
7. Remove  any...

CHASSIS AND BODY 
. I. ,. 9. Fit the  bezels  to  the  locking  button and  remote 
10. Fit  the  single screw  behind  the  remote control 
11. Fit the door  pull and secure  with two screws  and 
12. Fit the  window  regulator  handle and retain  with the 
control 
lever. 
lever. 
finishers. 
single screw  and finisher. 
,  ~ .. I. I 
76 
REMOVING 
WINDOW REGULATORS - rear side 
door 
Fitting regulator 
channel. 
5. Insert  the lifting  arm button  into  the  lifting 
To remove 
1. Remove  the door...

76 
REMOVING EXTERIOR HANDLE - rear side door 
CHASSIS AND BODY 
To remove 
1. Remove the door  trim,  regulator handle, door pull 
and bezels. 
2. Peel  back  sufficient  of the  weather protection  sheet 
to  gain  access 
to the handle  mechanism. 
3. Disconnect  the  actuating  rod from  the handle 
operating  lever. 
4. Remove the  two  screws  and  withdraw the handle 
and  bezels. 
Fitting 
handle 
5. Fit the  handle  to the  door  ensuring  that  the two 
bezels  are 
in position - flat faces...

CHASSIS AND BODY 176 
RENEW REMOTE  CONTROL  LEVER - rear side 
door 
To remove 
1. Remove  the door  trim,  door pull, regulator  handle 
2. Peel-back sufficient  of the  weather protection  sheet 
3. Remove the spring clip and disconnect  the control 
and 
bezels. 
to  gain  access  to the  remote  lever. 
rod from  the locking  button. 
Fitting control  lever 
9. Fit the  plastic  retaining  clips to the  rod  assembly 
10. Connect  the control  rods to the latch  assembly and 
11. Fit the plastic...

76 
Fitting the latch 
7. Fit the  latch  assembly  to the  door  and secure  with 
the  three  screws, noting that  the uppermost  screw 
is longer. 
8. Connect the remote  control  levers to  the  latch 
mechanism  reversing instructions 
3,4 and 5. 
9. Re-seal the weather  protection  sheet  and fit the 
regulator handle,  door pull, door  trim and bezels. 
CHASSIS AND BODY 
REMOVING DOOR GLASS - rear  side door 
To remove 
1. Disconnect  the door  check  rod from  the door  post. 
2. Remove  the...

CHASSIS AND BODY (761 
.: 
. . :.... .Y. ..L.-? 
11. Remove the four  self-tapping  screws - two each 
12. Remove  the inner  and outer  weather  strips from 
.*.

1761 CHASSIS AND BODY 
REMOVING MOUNTING  PANEL - front doors 
To remove 
1. Remove  the  door  trim, window regulator,  door 
pull,  bezels  and weather  protection  sheet. 
2. Remove the four  screws  securing  the window 
regulator  to the  mounting  panel. 
3. Remove the five screws securing  the mounting 
panel  to the  door frame. 
4. Release  the remote  control  lever rod from the  latch 
mechanism  and from  the plastic  clip 
in the 
mounting panel. 
5. Slide the  window regulator  arm from...