Land Rover Defender 300tdi Workshop 3rd Edition Rover Manual

COOLING SYSTEM
1
DESCRIPTION AND OPERATION ENGINE COOLING SYSTEM
Description
The complete cooling system of the 300Tdi engine
incorporates three independent functions:- Engine
(coolant) cooling; Turbo (charge air) intercooling;
Engine oil cooling.The intercooler is a separate aluminium unit, located
on the LH side of the engine compartment adjacent to
the radiator, sharing the same upper and lower
mountings. For details of turbo intercooling
See
FUEL SYSTEM, Description and operation,
Operation
. The oil...

26COOLING SYSTEM
2
DESCRIPTION AND OPERATION ENGINE (COOLANT) COOLING
Description
The 300Tdi engine uses a pressurised cooling system
and cross flow radiator which is supplied with coolant
from an expansion tank mounted on the RH side of
the engine compartment. A belt driven centrifugal
water pump, fitted to an auxiliary mounting assembly,pumps coolant to the engine crankcase, cylinder head
and vehicle heater unit.
An eleven bladed fan, incorporating a viscous
coupling, is driven by an independent pulley...

COOLING SYSTEM
3
DESCRIPTION AND OPERATION COOLANT CIRCULATION
Operation
When the engine is started from cold the thermostat
(2) prevents coolant circulation through the radiator by
closing off the top hose (6). During the engine warm
up period the water pump (5) circulates coolant to the
cylinders in the crankcase and through separate ports
to the cylinder head. At the rear of the cylinder head a
proportion of the flow is diverted through a heater feed
pipe (16) to the matrix of the heater unit (15)....

26COOLING SYSTEM
4
DESCRIPTION AND OPERATION Operation
To engage and disengage the fan drive the bi-metal
coil senses air temperature behind the radiator. When
a pre-determined temperature is reached, the coil
opens a valve (5) which allows fluid to enter the drive
area and, due to centrifugal force, circulates to the
annular drive area.
There are two sets of annular grooves (3), one in the
drive clutch and the other in the drive body, a specific
clearance being provided between the two sets of
grooves....

COOLING SYSTEM
1
ADJUSTMENT DRAIN AND REFILL COOLING SYSTEM
Service repair no - 26.10.01
Draining
WARNING: DO NOT remove caps or plugs
when the engine is hot. The cooling
system is pressurised and personal
scalding could result.
1.Remove expansion tank filler cap.
2.Position a clean container under radiator if
coolant is to be reused.
3.Disconnect radiator bottom hose and allow
coolant to drain.
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When...

COOLING SYSTEM
1
REPAIR VISCOUS COUPLING AND FAN
Service repair no - 26.25.19 - Viscous coupling
Service repair no - 26.25.05 - Fan
Remove
NOTE: The viscous coupling has a LH
thread.
1.Disconnect battery.
2.Using special pulley restraining toolLRT-12-094
and special spannerLRT-12-093unscrew
viscous coupling from pulley hub adaptor thread.
3.Remove viscous coupling and fan from vehicle.
NOTE: If air conditioning is fitted, the fan
cowl will also need removing,
See Fan
cowl
, with the viscous fan unit....

26COOLING SYSTEM
2
REPAIR FAN COWL
Service repair no - 26.25.11
Remove
1.Disconnect battery.
2.Drain coolant.
See Adjustment, Drain and
refill cooling system.
3.Slacken retaining clips and remove radiator top
hose.
4.Slacken retaining clip and remove top hose from
intercooler.
NOTE: On vehicles fitted with EGR system,
remove complete intercooler top hose
assembly.
5.Remove viscous coupling and fan
See Viscous coupling and fan.
6.Remove 2 nuts securing top of fan cowl.
7.Release expansion tank hose from...

COOLING SYSTEM
3
REPAIR WATER PUMP
Service repair no - 26.50.01
Remove
1.Disconnect battery.
2.Drain cooling system.
See Adjustment, Drain
and refill cooling system
3.Remove radiator top hose.
4.Remove intercooler top hose.
5.Slacken water pump and power steering pump
pulley retaining bolts.
6.Remove drive belt.
See ELECTRICAL, Repair,
Auxiliary drive belt
7.Unscrew flange nut and remove belt tensioner.
8.Remove oil filler cap and remove rocker cover
insulation.
9.Slacken retaining clip and disconnect...

26COOLING SYSTEM
4
REPAIRREV: 05/99 AUXILIARY MOUNTING BRACKET AND GASKET
Service repair no - 26.50.04
Remove
1.Disconnect battery.
2.Drain cooling system
See Adjustment, Drain
and refill cooling system
.
3.Remove radiator top hose.
4.Remove intercooler top hose.
5.Remove viscous fan unit.
See Viscous
coupling and fan
6.Remove fan cowl.See Fan cowl
7.Slacken power steering pump pulley retaining
bolts.
8.Remove drive belt.
See ELECTRICAL, Repair,
Auxiliary Drive belt
9.Unscrew 3 bolts and remove power...

COOLING SYSTEM
5
REPAIR 28.Secure steering pump and bracket to auxiliary
mounting bracket.
29.Fit steering pump pulley.
30.Fit drive belt
See ELECTRICAL, Repair,
Auxiliary drive belt
.
31.Fit fan cowl
See Fan cowl.
32.Fit viscous fan unit
See Viscous coupling and
fan
.
33.Fit intercooler top hose.
34.Fit radiator top hose.
35.Refill cooling system.
See Adjustment, Drain
and refill cooling system
36.Reconnect battery.THERMOSTAT
Service repair no - 26.45.01
Remove
1.Partially drain cooling system, until...