Land Rover Defender 300tdi Workshop 3rd Edition Rover Manual

12ENGINE
22
REPAIR
28.Lower cylinder head onto block ensuring correct
location with dowels.
NOTE: Cylinder head retaining bolts can
be used up to a maximum of five times.
29.Lubricate threads of bolts with light oil and fit to
positions shown below. (Fit air cleaner mounting
bracket at positions 6 and 14).
Bolt sizes:
M10 x 117mm locations 3, 5, 12, and 13.
M12 x 140mm locations 1, 2, 7, 8, 9, 10, 15, 16, 17,
and 18.
M12 x 100mm locations 4, 6, 11, 14.
30.Tighten bolts so that underside of heads just...

ENGINE
23
REPAIR
43.Check and adjust valve clearances.
See Adjustment, Valve clearances - check
and adjust
44.Fit rocker cover, ensuring oil seal is satisfactory
for continued use, and renew if necessary.
45.Secure rocker cover with special seal washers
and nuts. Tighten to
10 Nm (7 lbf/ft).
46.Fit rear engine lifting bracket, securing breather
pipe and multi-plug retaining clips. Tighten fixing
bolts to
25 Nm (18 lbf/ft).
47.Fit engine harness bracket to cylinder head.
48.Secure air cleaner mounting...

12ENGINE
24
REPAIR Refit
8.Fit oil pump rotors in front cover.
9.Apply a bead of RTV sealant around retaining
plate.
10.Fit oil pump retaining plate to front cover,
securely tighten screws.
11.Fit front cover to cylinder block.
See Front
cover gasket
OIL PRESSURE RELIEF VALVE
Service repair no - 12.60.56
Remove
1.Remove engine oil sump.
See Engine oil
sump
2.Unscrew relief valve retaining plug from base of
front cover.
3.Withdraw valve spring and plunger and check for
wear.
Valve spring free length,...

ENGINE
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine block
Bearing cap 133...............................................................................................
Blanking plug, oil gallery, rear 37....................................................................
Oil squirt jet assembly...

12ENGINE
2
SPECIFICATIONS, TORQUE REV: 05/99Nm
Cylinder head
Cylinder head to cylinder block
M10 x 117 40 Nm + 60° ..........................................................................................
M12 x 100 40 Nm + 60° ..........................................................................................
M12 x 140 40 Nm + 60°+20° ......................................................................................
Stub pipe heater feed...

ENGINE
3
SPECIFICATIONS, TORQUENm
Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor...

12ENGINE
4
SPECIFICATIONS, TORQUEMETRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12...

FUEL SYSTEM
1
DESCRIPTION AND OPERATION DESCRIPTION
Fuel system
The fuel system incorporates a supply and spill return
line on all models as illustrated below.
On 90 models, see J6191, the fuel tank is mounted at
the RH side of the vehicle chassis under the front
seat.On standard 110 and 130 models the fuel tank is
located at the rear of the vehicle between the chassis
longitudenal sections, as shown in J6192.
As an option, a twin tank system fitted with a
combined change-over tap and 3 way fuel supply...

19FUEL SYSTEM
2
DESCRIPTION AND OPERATION A mechanical lift pump, with a hand priming facility, is
driven by the camshaft, and is mounted on the RH
side of the engine.
A fuel filter, with a replaceable element and
incorporating a water separator, is mounted on the
front RH side of the engine compartment.
A fuel sedimentor may be fitted when the vehicle is
operating in more arduous conditions, and is used to
minimise water deposits in the fuel system before
reaching the fuel pump and filter.
Fuel...

FUEL SYSTEM
3
DESCRIPTION AND OPERATION
90 FUEL SYSTEM
110 FUEL SYSTEM
1.Fuel filter
2.Supply pipe, lift pump to filter
3.Supply pipe, fuel filter to injection pump
4.Fuel injection pump
5.Fuel lift pump
6.Spill return pipe, injection pump to tank7.Supply pipe, sedimentor to fuel pump
8.Fuel tank
9.Supply pipe, fuel tank to sedimentor
10.Fuel filler pipe
11.Breather pipe
12.Sedimentor, if fitted
NOTE: If a sedimentor is not fitted, the fuel
supply pipe from the tank will connect
directly to the fuel lift...