Home
>
Land Rover
>
Automobile
>
Land Rover Defender 1999 2002my Workshop Supplement Body Repair 2nd Edition Rover Manual
Land Rover Defender 1999 2002my Workshop Supplement Body Repair 2nd Edition Rover Manual
Have a look at the manual Land Rover Defender 1999 2002my Workshop Supplement Body Repair 2nd Edition Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
76CHASSIS AND BODY 12 REPAIR SEAT BELT - FRONT Service repair no - 76.73.13 Remove 1.Remove cap from seat belt guide bolt. 2.Remove bolt securing seat belt guide to’B’post. 3.Release belt from’B’post mounting. 4.Remove 3 bolts securing belt bracket to seat base. 5.Remove 2 studs securing seat belt retaining clip. 6.Remove retaining clip. 7.Remove bolt securing inertia reel to body. 8.Remove automatic belt assembly. 9.Remove 2 bolts securing stalk to body. 10.Remove stalk. Refit 11.Position stalk and tighten bolts. 12.Position automatic belt assembly to body and tighten bolt to38 Nm 13.Unreel portion of belt. 14.Position bracket to seat base, tighten bolts. 15.Position belt to’B’post mounting and tighten bolt to32 Nm (24 lbf.ft). 16.Fit cap to bolt head. 17.Position belt retaining clip to seat base and secure with studs.
CHASSIS AND BODY 13 REPAIR SEAT BELT - CENTRE - REAR Service repair no - 76.73.20 Remove 1.Remove seat belt bolt caps and remove bolts. 2.Remove seat belt and stalk. Refit 3.Position seat belt and stalk. 4.Fit and tighten bolts to32 Nm (24 lbf.ft),and fit bolt caps.SEAT BELT - REAR - SIDE Service repair no - 76.73.23 Remove 1.Remove cap from seat belt guide bolt. 2.Remove seat belt upper and lower securing bolts. 3.Remove seat belt guide from’D’post finisher. 4.Remove 2 studs securing finisher to’D’post.
76CHASSIS AND BODY 14 REPAIR 5.Release finisher from body upper rail and’D’ post. 6.Pull seat belt through’D’post finisher. 7.Remove bolt securing seat belt to’D’post and remove belt assembly. Refit 8.Position seat belt assembly to’D’post and tighten bolt to32 Nm (24 lbf.ft). 9.Extend seat belt and position through’D’post finisher. 10.Fit and tighten seat belt upper and lower securing bolts to32 Nm (24 lbf.ft). 11.Secure’D’post finisher to body upper rail. 12.Fit belt guide to’D’post finisher and fit finisher retaining studs. 13.Fit cap to seat belt bolt.SEAT - REAR Service repair no - 78.10.48.99 Remove 1.Remove bolts securing rear seat to hinges and collect spacer. 2.Remove rear seat. Refit 3.Position rear seat and align to hinges. 4.Fit spacer and tighten bolts.
CHASSIS AND BODY 15 REPAIR COVER - CUSHION - REAR SEAT Service repair no - 78.40.04 Remove 1.Remove rear seat.See this Section. 2.Remove 2 bolts securing squab to cushion frame. 3.Remove squab and collect spacer. 4.Remove 17 screws securing base board to seat cushion frame and remove board. 5.Remove 2 trim retaining clips. 6.Release cover retainers from seat frame. 7.Remove cover from cushion pad. Refit 8.Position cover to cushion pad and secure retainers to seat frame. 9.Fit trim retaining clips. 10.Position base board and tighten screws. 11.Position and align squab to cushion frame. 12.Fit spacer and tighten securing bolts. 13.Fit rear seat.See this Section.
76CHASSIS AND BODY 16 REPAIR COVER - SQUAB - REAR SEAT Service repair no - 78.90.13 Remove 1.Remove rear seat.See this Section. 2.Remove 2 screws and remove squab striker. 3.Remove 2 bolts securing squab to cushion frame. 4.Remove squab stop bolt. 5.Remove squab and collect spacer. 6.Release velcro securing squab cover edges and fold cover over squab pad. 7.Remove squab cover. Refit 8.Position cover to squab pad, align to its fitted position and secure velcro. 9.Position and align squab to cushion frame. 10.Fit spacer and tighten securing bolts. 11.Fit and tighten squab stop bolt. 12.Fit squab striker and tighten screws. 13.Fit rear seat.See this Section.REGULATOR - REAR DOOR GLASS Service repair no - 76.31.46 Remove 1.Remove rear door trim casing.See this Section. 2.Carefully release plastic sheet from rear door. 3.Remove 2 bolts securing door glass to regulator. 4.Raise glass and secure with a suitable wedge. 5.Remove 4 bolts securing glass regulator assembly to door. 6.Manoeuvre regulator through access hole at bottom of the door. Refit 7.Clean mating face of regulator and door glass. 8.Lubricate regulator with grease. 9.Position regulator in door and secure with bolts. 10.Remove wedge holding glass and align glass to regulator. 11.Secure glass to regulator and fit and tighten bolts. 12.Fit plastic sheet to rear door. 13.Fit rear door trim casing.See this Section.
CHASSIS AND BODY 17 REPAIR TRIM CASING - REAR DOOR Service repair no - 76.34.04.99 Remove 1.Remove screw securing door handle escutcheon. 2.Remove escutcheon. 3.Remove interior lock button bezel. 4.Remove retaining clip and remove door glass regulator handle. 5.Release covers and remove 2 screws securing door pull to door. 6.Carefully release 12 clips securing trim casing to door and remove door casing.Refit 7.Fit trim casing to door and secure with clips. 8.Fit door glass regulator handle. 9.Fit escutcheon to door handle and tighten screw. 10.Fit door lock button bezel. 11.Fit door pull and secure with screws.
76CHASSIS AND BODY 18 REPAIR AUXILLIARY SWITCH PANEL Service repair no - 76.46.38 Remove 1.Remove 2 screws securing axilliary switch panel to fascia and collect nuts and washers. 2.Disconnect multiplug from headlamp Levelling switch. 3.Disconnect multiplug and Lucar from cigar lighter. 4.Noting their fitted position, disconnect 4 Lucars from rear wash wipe switch. 5.Remove switch panel.Do not carry out further dismantling if component is removed for access only.6.Release pin securing rear wash wipe knob to switch and remove knob. 7.Remove locknut securing rear wash wipe switch to panel. 8.Remove rear wash wipe switch. 9.Remove knob from headlamp levelling switch. 10.Remove locknut securing headlamp switch to panel. 11.Remove headlamp levelling switch. 12.Remove element from cigar lighter. 13.Release bulb holder from cigar lighter. 14.Release cigar lighter from tags and remove from panel. 15.Fit cigar lighter to panel and locate tags. 16.Fit bulb holder to cigar lighter. 17.Fit element to cigar lighter. 18.Fit headlamp levelling switch to panel and secure with locknut. 19.Fit knob to headlamp levelling switch. 20.Fit rear wash wipe switch to panel and secure with locknut. 21.Fit knob to rear wash wipe switch, ensuring pin is correctly located. Refit 22.Position auxilliary switch panel to fascia and connect 4 Lucars to rear wash wipe switch. 23.Connect multiplug and Lucar to cigar lighter. 24.Connect multiplug to headlamp levelling switch. 25.Fit auxilliary switch panel to fascia and secure with screws.
CHASSIS AND BODY 19 REPAIR LOWER FASCIA PANEL - UP TO 02MY Service repair no - 76.46.05 Remove 1.Disconnect battery negative lead. 2.Remove steering wheel.See STEERING, Repair. 3.Remove 7 screws securing nacelle to steering column. 4.Remove 2 halves of nacelle from steering column. 5.Remove instrument pack.See ELECTRICAL, Repair. 6.Remove 3 screws securing heater control cable assembly to end of fascia. 7.Release heater control cable assembly from fascia and move aside. 8.Release HRW, Rear Fog Guard Lamp, and Hazard Warning switches from fascia. 9.Disconnect multiplugs and Lucars from switches. 10.Collect switches. 11.Remove locking rings from both front speakers. 12.Remove 4 screws securing each speaker to fascia. 13.Disconnect multiplugs from speakers and remove both front speakers.
76CHASSIS AND BODY 20 REPAIR 14.Carefully prise Land Rover decal from grab handle. 15.Remove 2 screws securing grab handle to crash pad and lower fascia panel. 16.Remove grab handle. 17.Remove 4 screws securing demister vents to crash pad. 18.Remove both demister vents. 19.Remove 3 screws securing crash pad to bulkhead. 20.Remove crash pad. 21.Release radio from fascia. 22.Disconnect 2 multiplugs and aerial from radio.23.Remove radio. 24.Remove 2 trim studs securing radio housing to fascia. 25.Remove radio housing. 26.Remove auxilliary switch panel.See this Section. 27.Remove auxilliary switch panel cover. 28.Remove interior fuse box cover.
CHASSIS AND BODY 21 REPAIR 29.Remove 2 screws securing each footwell vent and remove vents from lower fascia. 30.Remove screw securing each door check strap cover and remove both covers. 31.Remove 3 screws securing wiper motor cover to bulkhead. 32.Remove wiper motor cover. 33.Remove 3 screws securing finisher rail to lower fascia. 34.Remove finisher rail.