Kyocera KM C3232 User Manual

							Maintenance5-5
Toner Container and Wast e Toner Box Replacement
This machine uses 4 types of toner: 
cyan (C), magenta (M), yellow (Y) and 
black (K). When the touch panel displays 
Add toner. [C] [M] [Y] [K], replace the 
toner container for the color shown. 
Replace the toner without delay when 
this message is displayed. When 
replacing the toner container, also 
replace the waste toner box. 
Replace the toner container only if this 
messages appears.
NOTE:  Press [Adding toner] to display the repl acement instructions on the touch panel.
If you close the front cover without 
installing toner containers, a screen 
asking to check whether the toner 
containers are installed is displayed on 
the touch panel.
Open the front cover and check whether 
all of four toner containers are installed. 
If all of four toner containers are 
installed, press [Yes].
IMPORTANT:  If you press [Yes] when one or more toner containers are not installed, the machine 
may be damaged. Be sure to close the front co ver after all of four toner containers have been 
installed.
Also if toner containers other than specified by our company are installed, the same check screen is 
displayed. The machine can be used by pressing [Yes]. To ensure quality, though, it is 
recommended to use the toner cont ainers specified by our company.
Replacement of black toner is explained here as an example. 
1Open the front cover.
Caution: Do not attempt to incinerate the toner  container or the waste toner box. 
Dangerous sparks may cause burns.
Caution: Do not attempt to force open or dest roy the toner container or the waste 
toner box.
Add toner.
See the toner container box or
operation manual for replacement procedures and r epl ace the toner  contai ner Op e n th e  fr o nt co v e r  o f the  ma chi ne
[C][M]
Yes No
Are all of four toner containers installed?
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance
5-6
2Turn the toner container lock lever to the vertical 
position.
3Push up the toner container top clip A and pull the 
toner container down towards you. 
4Lift the toner container up and out. 
5Close the pickup opening, with the cap attached to the 
back side, on the old toner container. 
Caution: Do not attempt to incinerate the toner  container or the waste toner box. 
Dangerous sparks may cause burns.
Caution: Do not attempt to force open or destroy the toner container or the waste 
toner box.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance5-7
6Place the used toner container  in the provided plastic 
disposal bag.
7Remove the new toner container from the box.
8Hold the toner container with the toner container lock 
lever positioned on the top, and tap the top side ten 
times or more while keeping the container horizontal.
9Holding the toner container in both hands, hold 
vertically and shake up and down strongly at least ten 
times to distribute the toner evenly. 
IMPORTANT:  Do not install the toner container 
before shaking it sufficient ly. This may cause errors 
due to insufficient toner replenishment.
10Insert the new toner container into the machine.
11Press in the toner container upper portion. There will be 
an audible ‘click’ when the container is inserted in the 
correct position.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance
5-8
12Return the toner container lock lever to its original 
position.
Replace the other toner colors in the same fashion. 
13Hold down waste toner box release lever B, and slowly 
pull out the waste toner box. 
NOTE:  Do not turn the removed old waste toner box 
upside down. 
14As shown in the illustration, seal the old waste toner 
box with a cap. 
15Place the used toner container in the provided plastic 
disposal bag. 
16Remove the cap from the new waste toner box. 
B
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance5-9
17Install the new waste toner box.
18Close the front cover.
After use, always dispose of the toner contai ner and the waste toner box in accordance with 
Federal, State and Local rules and regulations.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance
5-10
Downloaded From ManualsPrinter.com Manuals 
						

							6-1
6 Troubleshooting
This chapter explains how to solve problems with the machine.
• Solving Malfunctions...6-2
• Responding to Error Messages...6-4
• Clearing Paper Jams...6-15
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
6-2
Solving Malfunctions
The table below provides general guidelines for problem solving.
If a problem occurs with your machine, check the checkpoints and perform procedures indicated on 
the following pages. If the problem persists, contact your Service Representative.
Symptom Checkpoints Corrective Actions Reference 
Page
The operation panel does 
not respond when the 
machine is turned on ( | 
position).Is the machine plugged in? Plug the power cord into an AC outlet. —
Pressing the Start key 
does not produce copies.Is a message displayed on the touch 
panel? Determine the appropriate response to 
the message and take action 
accordingly.page6-4
The original size is not 
detected properly.Are the originals loaded correctly? When placing originals on the platen, 
place them face-down and align them 
with the original size indicator plates.page2-16
Place originals face-up in the optional 
document processor. page2-18
Is the machine installed beneath 
fluorescent lights?Do not install this machine beneath 
fluorescent lights.—
Blank sheets are output. Are the originals loaded correctly? When placing originals on the platen, 
place them face-down and align them 
with the original size indicator plates.page2-16
Place originals face-up in the optional 
document processor. page2-18
Is the machine installed beneath 
fluorescent lights?Do not install this machine beneath 
fluorescent lights.—
Printing is too light.  Is the machine set to Manual Exposure 
mode? Use the exposure adjustment key to set 
the correct exposure level.page3-6
Is the toner distributed evenly within the 
toner container?Shake the toner container up and down 
approximately 10 times.page5-5
Is there a message indicating the 
addition of toner?Replace the toner container. page5-5
Is the copy paper damp? Replace the copy paper with new paper. page2-2
Printing is too dark.  Is the machine set to Manual Exposure 
mode? Use the exposure adjustment key to set 
the correct exposure level.page3-6
Copies have a moire 
pattern (dots grouped 
together in patterns and 
not aligned uniformly).Is the original a printed photograph? Set the image quality to [Print].  page3-5
Copies are not clear. Did you choose appropriate image 
quality for the original?Select an appropriate Image Quality 
mode.page3-5
Is the copy paper damp? Replace the copy paper with new paper. page2-2
Is special color copy paper being used? Use special color copy paper. —
Copies are dirty. Are the original platen or platen dirty?  Clean the original platen or platen glass.  page5-2
Printer output is fuzzy. Is the copy paper damp? Replace the copy paper with new paper. page2-2
Is special color copy paper being used? Use special color copy paper. —
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
6-3
Printing is skewed.  Are the originals loaded correctly? When placing originals on the platen, 
place them face-down and flush against 
the original size indicator plates.page2-16
When placing originals in the document 
processor, align the original width 
guides securely before placing the 
originals.page2-18
Is the paper loaded correctly? Check the position of the paper width 
guides.page2-2
Paper jams frequently 
occur.Is the paper loaded correctly? Load the paper correctly. page2-2
Is the paper of the supported type? Is it 
in good condition?Remove the paper, turn it over, and 
reload it.page2-2
Is the paper curled, folded, or wrinkled? Replace the paper with new paper. page2-2
Are there any loose scraps or jammed 
paper in the machine?Remove any jammed paper. page6-15
Is the copy paper damp? Replace the copy paper with new paper. page2-2
Is special color copy paper being used? Use special color copy paper. —
Copies from the optional 
document processor 
have black lines.Is the slit glass dirty? Clean the slit glass.  page5-2
Printing is wrinkled.  Is the separator dirty?  Clean the separator.  page5-3
Is the copy paper damp? Replace the copy paper with new paper. page2-2
Is special color copy paper being used? Use special color copy paper. —
Is the paper set in a proper orientation? Change the orientation in which the 
paper is positioned.—
Unable to print.  Is the machine plugged in? Plug the power cord into an AC outlet. —
Is the machine switched on?  Turn the main power switch to on ( | 
position). —
Is the printer cable connected?  Confirm the printer cable is securely 
connected. page2-21
Was the printer switched off when 
connecting the printer cable? Switch on the printer after connecting 
the printer cable. page2-21
Is the device in Offline mode?  Press the Printer key and press [GO] to 
restore Online mode. —
Characters are not 
printed correctly. Is the printer cable connected?  Confirm the printer cable is securely 
connected. page2-21
Are the computer settings configured 
correctly? Confirm printer driver and application 
software settings. —
Print output is not correct.  Are the computer settings configured 
correctly? Confirm printer driver and application 
software settings. — Symptom Checkpoints Corrective Actions Reference 
Page
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
6-4
Responding to Error Messages
If the touch panel displays any of these messages, follow the corresponding procedure.
Copy Error Messages
If the Copy mode touch panel displays any of these messages, follow the corresponding procedure.
Error Messages Checkpoints Corrective Actions Reference 
Page
Close ### cover.Is the indicated cover open?Close all covers securely. —
Check the cover.Are any covers open?
Does the message indicate which 
cover is open? Close all covers securely. —
Close Document processor.Is the optional document processor 
open while loading the original?Close the document processor. —
Close Document processor 
cover.Is the optional document 
processor’s document processor 
cover open? Close the document processor 
cover.page6-26
Set cassette #.
(Close paper cassette #.)Is the indicated cassette not fully 
closed?Pull out the cassette and push in 
securely.—
Open cassette #, check and 
remove paper from inside of the 
machine.
(Open cassette #, check and 
remove paper from inside of 
machine.)— Completely pull out the indicated 
cassette and remove any paper 
inside. —
Reset feeding unit for paper 
cassette.Is the paper feeder securely pushed 
into the machine?Pull out the paper feeder and 
securely push it all the way into the 
machine.page6-19
Add paper in cassette #.
(Add paper cassette #.)Is the indicated cassette out of 
paper?Load paper. If the same type of 
paper is loaded in another cassette 
in the same orientation, you can 
press either one of paper selection 
keys on the left of the touch panel to 
switch to that cassette for copying.—
Add paper in the Multipurpose 
tray. 
## size
(Place paper on the 
Multipurpose tray.
## size)Is paper of the specified size loaded 
in the MP tray?Load paper of the size indicated in 
the MP tray.page2-5
Add paper in the Multipurpose 
tray.
(Add paper on the Multipurpose 
tray.)Has all the paper on the MP tray 
been fed? Load paper in the MP tray. page2-5
Place transparency in the 
Multipurpose tray.
(Place transparencies on the 
Multipurpose tray.)Are any transparencies loaded in the 
MP tray?Place transparencies on the MP tray. page2-5
Change the size of MP tray.Is the specified size paper loaded in 
the MP tray?Reconfigure the size of the MP tray. page2-10
Downloaded From ManualsPrinter.com Manuals