Kyocera KM 2035 User Manual

							Copying Functions 
OPERATION GUIDE4-11
1Set the original.
NOTE: The Border Width can also be set in the System Menu. (Refer to 
Setting the Border Width on page 4-11.)
The value set in the System Menu will inherit the value that is set at the 
time when the copy is made.
2Press [Border Erase] and select the type of border erase to be performed 
to light up the   or   indicator.
3Press [Start]. The copier will begin copying.
Setting the Border Width
Use the procedure given below to change the Border Width.
1Press [Border Erase] for 3 seconds. The 
System Menu for the Border Width will be 
displayed.
2Press U or V and select the border width. 
[Inch specifications]
Select from 0.13 (), 0.25 (), 0.38 (), 0.50 (), 0.63 () or 0.75().
[Metric specifications]
Select from 1 to 18(mm).
3Press [OK]. The display will blink and the copier will return to the state 
where copying can be continued.
44.Border Erase
             1mm
Downloaded From ManualsPrinter.com Manuals 
						

							Copying Functions 
4-12OPERATION GUIDE
Copying 2 or 4 originals onto a single page
The sizes of 2-sheet or 4-sheet 
originals can be reduced and 
copied together onto a single 
sheet. In addition, the borders of 
each original can be separated 
with a solid or dotted line.
NOTE: Only standard paper sizes and originals can be used for this.
2 in 1
2 sheets of originals can be 
copied onto a single sheet. If 
used together with 2-Sided 
Copy, 4 sheets of originals can 
be copied onto both sides of a 
single sheet.
(Follow the order shown in 
illustrations 1 → 2 in placing the 
originals on the platen.)
The directions for setting the original and the finished copy are as follows.
2
112


















Original Copy
Downloaded From ManualsPrinter.com Manuals 
						

							Copying Functions 
OPERATION GUIDE4-13 When the original is set on the platen
Original Setting Direction Finished Product
1


1


1



1


Downloaded From ManualsPrinter.com Manuals 
						

							Copying Functions 
4-14OPERATION GUIDE When the original is set in the Document Processor
Original Setting Direction Finished Product










Downloaded From ManualsPrinter.com Manuals 
						

							Copying Functions 
OPERATION GUIDE4-15
4 in 1
4 sheets of originals can be 
copied onto a single sheet. If 
used together with 2-Sided 
Copy, 8 sheets of originals can 
be copied onto both sides of a 
single sheet.
(Follow the order shown in 
illustrations 1 → 2 → 3 → 4 in 
placing the originals on the 
platen.)
The directions for setting the original and the finished copy are as follows.
When the original is set on the platen
Original Setting Direction Finished Product
4
3
2
1
4
21
3
42
13
1
3
2
4
13
42
4
3
2
1
Original Copy
Portrait
Landscape
1
111
1
1
Downloaded From ManualsPrinter.com Manuals 
						

							Copying Functions 
4-16OPERATION GUIDE When the original is set in the Document Processor
1Set the original.
NOTE: The 4 in 1 layout setting (refer to 4 in 1 Layout Order on page 4-
17) and the setting of border lines when setting Combine mode (refer to 
Setting the Combine mode Border Lines on page 4-17) can also be set in 
the System Menu.
The value set in the System Menu will inherit the value that is set at the 
time when the copy is made.
2Press [Combine] to light up the   or   indicator.
3Input the number of sets of copies using the numeric keys.
4Press [Start]. The copier will begin reading 
in the original.
When an original has been set in the 
optional Document Processor copying will 
begin automatically.Original Setting Direction Finished Product
111
1
Scanning.
        
Downloaded From ManualsPrinter.com Manuals 
						

							Copying Functions 
OPERATION GUIDE4-17 When the original has been set on the 
platen and the scanning of the original 
completed, Place next original. is 
displayed and the Combine indicator blinks. 
When this occurs, carry out the following 
procedure.
5Replace the original with the next one and press [Start]. The copier will 
read in the original.
6If there are no more originals, press [Combine] or [OK]. The copier will 
begin copying.
4 in 1 Layout Order
Follow the procedure below to change the order in which pages are to be 
laid out within the copied page when making 4 in 1 copies.
1Press [Combine] for 3 seconds. The 
System Menu will be displayed.
2Confirm that 45.4 in 1 Layout is displayed and then press [OK].
3Press U or V and select the 
layout. 
4Press [OK]. The display will blink and copying can be begun.
Setting the Combine mode Border Lines
Use the procedure given below to change the Combine mode Border 
Lines.
1Press [Combine] for 3 seconds. The System Menu will be displayed.
2Press U to display 46.Combine Border.
3Press the [OK].
4Press U or V and select the type of border line.
Place next
original.
45.4 in 1 Layout
      Portrait 1
1
1
34 2 4 2
3 Portrait 1 Portrait 2
Landscape 1  Landscape 2 1
1
24 3 4 3
2
System menu:
46.Combine Border
Downloaded From ManualsPrinter.com Manuals 
						

							Copying Functions 
4-18OPERATION GUIDE Off
Solid
Dotted
5Press [OK]. The display will blink and the copier will return to the state 
where copying can be continued.
Downloaded From ManualsPrinter.com Manuals 
						

							Copying Functions 
OPERATION GUIDE4-19
Automatic Collating of copy sets
It is possible to Collate the number 
of copy sets needed from multiple 
sheets of originals.
NOTE: Whether or not to 
collate while changing the 
direction for each set at the 
time of collating can be 
changed using the System 
Menu. (Refer to Rotate Collate 
Setting on page 5-19.)
1Set the original.
NOTE: When an original is set in the optional Document Processor, the 
Collate indicator will light and Collate Copies will be set. In this case, 
proceed to Step 3.
2Press [Collate].
3Input the number of sets of copies using the numeric keys.
4Press [Start]. The copier will begin reading 
in the original.
When an original has been set in the 
optional Document Processor copying will 
begin automatically.
3
2
1
1
1
1
2
2
2
3
3
3
3
2
1
3
2
1
3
2
1
3
2
1
No Collating
Copy
Original
OriginalCollating
Copy
Scanning.
Downloaded From ManualsPrinter.com Manuals 
						

							Copying Functions 
4-20OPERATION GUIDE When the original has been set on the 
platen and the scanning of the original 
completed, Place next original. is 
displayed and the Collate display blinks. 
When this occurs, carry out the following 
procedure.
5Replace the original with the next one and press [Start]. The copier will 
read in the original.
6If there are no more originals, press [Collate] or [OK]. The copier will begin 
copying.
Place next
original.
Downloaded From ManualsPrinter.com Manuals