Kyocera FS C5250DN User Manual
Have a look at the manual Kyocera FS C5250DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 73 Kyocera manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
6-15Troubleshooting 3Close the rear cover. Paper Jam at Cassette 2 (to 4) Paper is jammed at the paper cassette. Remove the jammed paper using the procedure given below. 1Pull out the paper cassette of the optional paper feeder and remove the jammed paper. 2Open the rear cover of the paper feeder and remove the jammed paper. Downloaded From ManualsPrinter.com Manuals
Troubleshooting 6-16 Downloaded From ManualsPrinter.com Manuals
A-1 Appendix This chapter lists the provides details of the available interfaces and describes the optional hardware that can be installed on the printer and shows the printers specifications. Interface A-2 USB Interface A-2 Network Interface A-3 About the Options A-5 Expansion Memory Modules A-6 General Description of Options A-8 Specifications A-12 For availability of the options, consult your service technician. Downloaded From ManualsPrinter.com Manuals
Appendix A-2 Interface This chapter explains the signals used in the printers USB, and network interfaces. It also lists pin assignments, signal functions, timings, connector specifications, and voltage levels. • USB Interface • Network Interface USB Interface This printer supports the Hi-Speed USB. USB (Universal Serial Bus) interface specifications and interface signals are as follows. Specifications Basic Specification Complies with the Universal Serial Bus Specification Revision 2.0. Connectors Printer: B-type receptacle (female) with upstream port Cable: B-type plug (male) Cable Use a shielded cable that complies with USB 2.0 (Hi-Speed USB) and not longer than 5 meters (16 feet). Transfer Mode High speed (480 Mbps maximum) Full-Speed (12 Mbps maximum) Power Control Self-power device Interface Signals USB Connector Pin Assignment PinSignalDescription 1 Vbus Power supply (+5 V) 2 D- Data transmission 3 D+ Data transmission 4 GND Signal ground Shell — Shield Downloaded From ManualsPrinter.com Manuals
A-3Appendix Network Interface Features Automatically Obtains an IP Address Supports the DHCP/DHCPv6 protocol and can receive an IP address assigned by a DHCP/DHCPv6 server. Management Using a Web Browser (COMMAND CENTER) HTTP pages (COMMAND CENTER) are incorporated into the interface, so that a web browser can be used to access the COMMAND CENTER to monitor and change a range of settings. The settings can be password- protected. Support for a Range of Protocols The SMTP, POP3, SSL, SNMP, IPv6 and NetBIOS over TCP/IP protocols are supported for easier printer management and more robust security. Support for IEEE 802.1x The interface supports EAP-TLS and PEAP authentication. Supports IPv6 Supports IPv6, which is based on IPv4 with improvements, such as increased manageable address space, additional security functions and priority based data transmission. Supports IPSec Supports IPSec, the security protocol that authenticates and encrypts in the network layer (IP layer). Specifications Connector 10 Base-T/100 Base-TX Operating Systems Windows 2000/XP/Vista/7/Server2003/Server2008, MacOS 10.x Network Protocols • IPv6: HTTP, LPD, FTP, IPP, RawPort, ICMPv6, LLTD, SNTP, DHCPv6, SMTP, POP3, DNS, SNMPv1/v2c/v3, WSD • IPv4: HTTP, HTTPS, LPD, FTP, IPP, RawPort, ICMP, DHCP, SMTP, POP3, SNTP, DNS, WINS, NetBIOS over TCP/IP, SNMPv1/v2c/v3, Apple Bonjour Compatible, IPPS, LLTD, WSD • Etc.: IPX/SPX, NetWare (NDS/Bindery), AppleTalk, NetBEUI Security Protocols SSL/TLS (HTTPS, IPPS), SNMPv3, EAP-TLS, PEAP, AH, ESP Downloaded From ManualsPrinter.com Manuals
Appendix A-4 Operation Environment 10 to 35 °C (50 to 95 °F), 20-80 % RH (condensation-free) EMI Countermeasures VCCI Class B, FCC Class B (U.S.), CE (Europe) IMPORTANT When IPv6 functions are used, the devices used on the network (routers, PCs, etc) must support IPv6. Downloaded From ManualsPrinter.com Manuals
A-5Appendix About the Options This printer has the following options available to satisfy your printing requirements. For instructions on installing individual options, refer to the documentation included with the option. Some options are explained in the following sections. Paper Feeder PF-520/ PF-530 (Only 2 stacked paper feeders can be used with the FS-C5150DN) Expansion Memory (DIMM 128/256/512/1024 MB) Hard Disk (FS-C5250DN only) USB memory Network Interface Card IB-23 Downloaded From ManualsPrinter.com Manuals
Appendix A-6 Expansion Memory Modules The printers main controller board has a memory slot into which you can plug in optional memory modules (dual in line memory modules). You can increase the printers memory up to 1,280 MB by plugging in the optional memory modules. Expansion Memory Modules You can select additional memory modules from 128, 256, 512 or 1,024 MB. The maximum memory size is 1,280 MB. Precautions for Handling the Printers Main Controller Board and Memory Modules To protect electronic parts, discharge static electricity from your body by touching a water pipe (faucet) or other large metal object before handling the memory modules. Or, wear an antistatic wrist strap, if possible, when you install the memory modules. Always hold the main controller board or a memory module by its edges as shown below to avoid damaging electronic parts. Installing the Memory Modules IMPORTANT Remove any USB memory that is attached to the print- ers USB memory slot. 1Power off the printer and unplug the printer power cord. 2Pull the right cover of the printer toward you and remove. Note A 256 MB memory module is already installed at the factory. To expand memory up to 1,280 MB, install 1,024 MB memory module. YES NO Downloaded From ManualsPrinter.com Manuals
A-7Appendix 3Open the inside cover. 4Remove the memory module from its package. 5With the memory connection terminal pointing toward the socket, align the cut-out part with the socket terminal and insert directly in at an angle. CAUTION Before inserting a memory module in the machine, make sure that the machine is switched off. 6Carefully press the inserted memory down and into the machine. 7Reinstall the right cover. Removing a Memory Module To remove a memory module, remove the right cover, open the inner cover, and then carefully open the two socket clamps. Ease the memory module out of the socket to remove. Testing the expanded memory After you finish installing the memory module in the printer, test the printer to see if the installation was successful. To test the expansion memory, proceed as follows: 1Make sure the printer is turned off. Plug the power cord into the printer and turn the printer on. 2Press [Menu] on the operation panel. 3Press U or V repeatedly until Report Print > appears. 4Press Z while Report Print > is displayed. 5Press U or V repeatedly until > Print Status Page appears. 6Press [OK] twice. 7If the installation was successful, the amount of memory shown on the status page will correspond with the amount of expanded memory. (The factory installed memory size is 256 MB.) Downloaded From ManualsPrinter.com Manuals
Appendix A-8 General Description of Options PF-520, PF-530 Paper Feeder The optional paper feeder PF-520 (f or plain paper) and PF-530 (for multiuse media) will each hold approximately 500 sheets of paper (80 g/m²). Up to 3 optional feeders can be added to the bottom of the printer (only 2 stacked paper feeders can be used with the FS-C5150DN), allowing continuous feeding of up to 2,000 sheets of paper (1,250 sheets in the FS-C5150DN) when combined with the printers own cassette. IMPORTANT When you use the paper feeder, place the papers and envelopes print-side up. The papers that can be used in the cassettes supplied with the paper feeders are as follows: PF-520 : Paper size : Envelope Monarch, Envelope #10, Envelope #9, Envelope #6, Envelope DL, Envelope C5, A5, B5, ISO B5, A4, Executive, Letter, Legal, OufukuHagaki, Oficio II, Statement, Folio, Youkei 2, Youkei 4, 16K and custom (92 × 165 mm to 216 × 356 mm) Paper type : Plain, preprinted, bond, recycled, rough, letterhead, color, prepunched, thick, high quality, custom 1 (to 8) PF-530 : Paper size : Envelope Monarch, Envelope #10, Envelope #9, Envelope #6, Envelope DL, Envelope C5, A5, B5, ISO B5, A4, Executive, Letter, Legal, OufukuHagaki, Oficio II, Statement, Folio, Youkei 2, Youkei 4, 16K and custom (92 × 162 mm to 216 × 356 mm) Paper type : Plain, preprinted, labels, bond, recycled, rough, letterhead, color, prepunched, cardstock, envelope, coated, thick, high quality, custom 1 (to 8) IMPORTANT Place the paper feeders on a stable desk or base. When moving the printer with the PF-530 installed, disconnect the AC relay cord that connects the printer and the PF-530. Make sure the cover is attached during use. Downloaded From ManualsPrinter.com Manuals